www.nmletters.org Effective Doping of Rare-earth Ions in Silica Gel: A Novel Approach to Design Active Electronic Devices D. Haranath∗, Savvi Mishra, Amish G. Joshi, Sonal Sahai, Virendra Shanker (Received 21 June 2011; accepted 4 August 2011; published online 31 August 2011.) Abstract: Eu3+ luminescence spectroscopy has been used to investigate the effective doping of alkoxide-based silica (SiO2) gels using a novel pressure-assisted sol-gel method. Our results pertaining to intense photolumi- nescence (PL) from gel nanospheres can be directly attributed to the high specific surface area and remarkable decrease in unsaturated dangling bonds of the gel nanospheres under pressure. An increased dehydroxylation in an autoclave resulted in enhanced red (∼611 nm) PL emission from europium and is almost ten times brighter than the SiO2 gel made at atmospheric pressure and ∼50℃ using conventional Stöber-Fink-Bohn process. The presented results are entirely different from those reported earlier for SiO2:Eu 3+ gel nanospheres and the origin of the enhanced PL have been discussed thoroughly. Keywords: Luminescence; Nanophosphor; Short-range order; Electron microscopy Citation: D. Haranath, Savvi Mishra, Amish G. Joshi, Sonal Sahai and Virendra Shanker, “Effective Dop- ing of Rare-earth Ions in Silica Gel: A Novel Approach to Design Active Electronic Devices”, Nano-Micro Lett. 3 (3), 141-145 (2011). http://dx.doi.org/10.3786/nml.v3i3.p141-145 Introduction Luminescent materials have been utilized widely in applications involving lighting to sensing [1]. The pho- toluminescence (PL) properties of silica have also been an important topic of research for a long time, but the difficulty in the incorporation of rare-earth (RE) ions attached covalently to the silica (SiO2) network is still considered a great challenge. The weak PL bands with peak energies ∼1.9-4.3 eV for both bulk and thin films of SiO2 have been reported [2]. The sol-gel method has been used to prepare nanomaterials in the form of powders, films, fibers and monoliths that are based on various metal alkoxides [3]. It has been observed that monodisperse silica nanospheres formed by hydrolysis and condensation of alkoxides using Stöber-Fink-Bohn (SFB) process gives negligible luminescence. Incorpora- tion of inorganic luminescent centres into SFB spheres has been demonstrated by some research groups [4] us- ing RE ions, quantum dots and organic flurophores, but the procedure requires multiple processing steps and use of expensive and toxic ligands. During the last few years, there have been few reports [5-10] on intense PL emission in the visible region of the electro- magnetic spectrum, by several different nanostructured materials that are highly disordered such as nanowires, porous silicon, silica-based mesoporous fractals, ferro- electrics with ABO3 type and AWO4-type perovskite structures (A=Ca, Ba, Sr); and many more. The ori- gin of this type of luminescence is always attributed to unsaturated chemical bonds in these nanostructures. In case of ferroelectrics, as their energy band gaps are lo- cated ∼3-4 eV, the PL emission in the visible region was correlated to their highly disordered states and many localized electronic levels present within the op- tical gap, causing luminescence [6]. Since SiO2 gel is a well-studied system [11] having visible transparency and significant absorption peak lying in the ultra-violet National Physical Laboratory, Council of Scientific and Industrial Research, Dr K S Krishnan Road, New Delhi, 110 012, India *Corresponding author. E-mail: haranath@nplindia.org Nano-Micro Lett. 3 (3), 141-145 (2011)/ http://dx.doi.org/10.3786/nml.v3i3.p141-145 Nano-Micro Lett. 3 (3), 141-145 (2011)/ http://dx.doi.org/10.3786/nml.v3i3.p141-145 region, the introduction of dopant ions act as a pertur- bation to the well-studied system leading to interesting optical properties. The RE ions are used as probes in the sol-gel method due to their sensibility to change with the surrounding matrix probing the local struc- ture [12,13]. Thus derived SiO2 and organically modi- fied matrix composites could be the main precursor to prepare many RE based smart optical materials [14]. In this paper, we propose a novel methodology to pre- pare alkoxide-based silica gel nanospheres doped with Eu3+ ions that show enhanced PL brightness, uniform size distribution and improved quantum efficiencies. This is a process by which highly disordered but doped silica gels could be effectively made useful for practi- cal applications involving luminescence. It has already been evidenced that high pressure and temperature leads to more closely packed structures [14]. The pre- sented analogy is unique and could be extended to many crystalline and non-crystalline phosphor based systems to design new family of sol-gel based nanocomposites, having a wide variety of applications in lasers, chemi- cal sensing, waveguides, bioanalytical assays, blood flow monitoring and effectively harvesting the solar energy for improving the solar cell efficiency. Experimental Silica nanospheres were prepared with its surface modified by sol-gel method and studied through the incorporation of Europium (III) ions in two differ- ent ways. The europium nitrate (EuNO3) was mixed with sufficient ethanol (EtOH) and this was added to tetraethylorthosilicate (TEOS). The stoichiometric amount of water, which is essential to carryout hydrol- ysis reaction, was added drop wise under continuous stirring. Prior to gelling the low and high resolution transmission electron microscopy (TEM) images of col- loidal silica solution (also called silica sol) were taken at a magnification of 125 and 400 kX, respectively as shown in Fig. 1. The silica particles observed are al- most spherical with an average cluster size of ∼5 nm. The schematic of the SiO2 gel network [11] and the probable description of pore and particle sizes were il- lustrated in Fig. 1(c). The silica sol was then divided in two halves for a systematic experimentation. For the first experiment, one of the solution containing vials was allowed to gel at atmospheric pressure (1 bar) and a controlled oven temperature of ∼50℃ (±0.1℃). In the second case the solution was kept in an auto- clave, subjected to high temperature and pressure at ∼150℃ and 120 bars, respectively for about 5 hours. It was intentional to keep the processing time same for both the cases. Once the wet silica gels were obtained, SiO2:Eu 3+ nanospheric powders were obtained by dry- ing the gels overnight in vacuum oven at ∼55℃. All the samples were studied using morphology, composi- tion evaluation, UV-VIS absorption and luminescence spectroscopy techniques. Fig. 1 (a) TEM and (b) HRTEM images of silica sol particles aged for 5 hours at room temperature, 25℃; (c) schematic illustration of gel network structure showing the pore and particle sizes (Courtesy from ref. [11]). For TEM observations, the samples were redispersed in methanol by ultrasonic treatment and dropped on carbon-copper grids. TEM images were collected using a Tecnai G2 F30 S-Twin (FEI; Super Twin lens with CS=1.2 mm) instrument operating at an accelerating voltage at 300 kV, having a point resolution of 0.2 nm and lattice resolution of 0.14 nm) with an EDAX at- tachment. Program Digital Micrograph (Gatan) was used for image processing. Scanning electron mi- croscopy was performed using Zeiss EVO MA10. X-ray diffraction (XRD) of the powder sample was performed using Bruker D-8 advance powder X-ray diffractometer with CuKα radiation operated at 35 kV and 30 mA. All the samples showed the amorphous na- ture. X-ray Photoelectron Spectroscopy (XPS) studies have been carried out using a Perkin Elmer 1257 model, at 300 K with a non-monochromatic AlKα line at 1486.6 eV. During photoemission studies, small spec- imen charging was observed which was later calibrated by assigning the C 1s signal at 285 eV. The room temperature photoluminescence (PL) spectra were recorded using an Edinburgh Lumines- cence Spectrometer (Model F900) equipped with a xenon lamp. The excitation and emission spectra were recorded in the fluorescence mode over the range of 300- 700 nm. Results and discussion It is important to highlight the pressure-assisted hy- drothermal/solvothermal process for the preparation of variety of nanoparticles of oxides and chalcogenide ma- terials. The solution based nanomaterial synthesis of- ten involves reactions carried out near the boiling point 142 Nano-Micro Lett. 3 (3), 141-145 (2011)/ http://dx.doi.org/10.3786/nml.v3i3.p141-145 of the solvent. This may lead to poor quality of the nanomaterial and less yield. In order to obtain crys- talline, monodisperse nanoparticles, it is always neces- sary to work at relatively high temperatures and pres- sures. Use of acid digestion bomb (commonly called Autoclave) is the best alternative to work with. De- tails of the autoclave synthesis of intrinsic silica gels have been reported extensively by Haranath et al. since 1996. In the current case, rare-earth (RE) doped sil- ica gels were made under pressure at elevated temper- atures as described in latter sections. This method of preparation, which is based on pressure-assisted sol-gel method, has compatibility in modifying the coordinat- ing environment of RE (dopant) ions so that the loss in energy of the excited states via. non-radiative mech- anism is minimum. The x-ray diffraction pattern of Eu3+ doped SiO2 gel powder depicted in Fig. 2 clearly shows a broad hump at ∼23◦ indicating the complete amorphous nature of the SiO2 nanospheres. SEM im- ages shown in inset of Fig. 2 illustrate the quality of the nanospheres with respect to their size and shapes. In other words, the conventional sol-gel method leads to a broad distribution of particle sizes in the range 10-50 nm (Fig. 2(a)) whereas the pressure assisted sol- gel method has resulted in almost uniform particles (∼15 nm) with spherical shape (Fig. 2(b)). This es- tablishes the fact that high pressure and temperature leads to more closely packed structures and increased charge transfer energies that are efficiently transferred to the Eu3+ ions. The TEM and scanning electron mi- crographs (SEM) reveal that the optimization of exper- imental and processing parameters allow microscopic preparation of uniform silica nanospheres. Fig. 2 X-ray diffraction (XRD) pattern of SiO2 gel pow- der at room temperature (∼25℃) indicating the amorphous nature of the gel under study. The insets shows the SEM micrographs of SiO2:Eu gels prepared at (a) atmosphere pressure (1 bar) and 50℃; and (b) 120 bars and 150℃, re- spectively. Moreover, the chemical composition and the relevant surface chemistry of SiO2:Eu 3+ nanospheres were an- alyzed using x-ray photoelectron spectroscopy (XPS). The XPS observations revealed three peaks correspond- ing to the elements Si, O and Eu, respectively. Pass energy for general survey scan and core level spectra was kept at 143.05 and 71.55 eV respectively. Sur- face contamination was removed by Ar ions with 4 keV beam energy. Sputtering performed in raster mode with emission current of 20 mA for 5min at base pres- sure 4.5×10−7 torr. Figure 3 shows the survey spectra of SiO2:Eu 3+ nanospheres acquired in the range of 0- 1200 eV. During photoemission studies, small specimen charging was observed, which was later calibrated by assigning the C 1s signal at 285 eV. Survey spectra af- ter sputtering show sharp peaks of C 1s (285 eV), O 1s (537 eV). Two clear distinct state of Eu were observed at 1171 and 1141 eV for Eu 3d3/2 and 3d5/2 respec- tively. The separation between two states is because of spin-orbit splitting. Inset of Fig. 3 shows the Si(2p) core level spectra. The value of elemental Si(2p) is 99.15 eV, since, appearance of Si(2p) at 104 eV confirms the Si exist in SiO2 state. The binding energies of various elements match very well with the peaks observed for standard SiO2:Eu 3+. The presence of C is due to the air atmosphere and the organics used for the preparation of Eu3+ doped in silica matrix. Fig. 3 XPS survey scan spectra of sputtered and nanopar- ticles of SiO2:Eu 3+ recorded with photon energy of AlKα (hν=1486.6 eV), Inset shows the Si(2p) core level. Figure 4 shows the UV-VIS absorbance spectra of Eu3+ doped SiO2 gel samples prepared at 50℃, 1 bar; and 150℃, 120 bars, respectively. The spectra are the strong indicative two findings. One is being the reduc- tion of surface states of the gel nanospheres and other being the maintenance of almost the same size for the gel particles even after subjecting to high pressure and temperature cycles. The same has been evidenced by the absorption peaks indicated in the inset of Fig. 4. 143 Nano-Micro Lett. 3 (3), 141-145 (2011)/ http://dx.doi.org/10.3786/nml.v3i3.p141-145 2.5 2.0 1.5 1.0 330 336 342 nm A b s. 332 nm 334 nm 3 2 1 0 325 350 375 400 450425 Wavelength (nm) A b so rb a n ce ( % ) 50°C, 1 bar 150°C, 120 bar Fig. 4 Absorbance spectra of Eu doped-SiO2 samples pre- pared at atmosphere pressure (1 bar) and 120 bars and 150℃, respectively. Inset shows the expanded version of the absorption peaks. The observation of weak photoluminescence (PL) at room temperature in various amorphous silica nanos- tructures has been reported in the literature [15-18] but not sufficient to use for any fundamental or potential application. Figure 5 shows the PL excitation (PLE) and PL spectra from Eu3+ doped and baked SiO2 gel in an autoclave respectively. It is known that the sur- face states and unsaturated dangling bonds play a crit- ical role in determining the overall PL characteristics of nanostructures. If the silica gel is prepared with a rare-earth dopant (Eu3+ in the present case), the PL is dominated by the radiative transitions (5D0 → 7Fj, j=0-3) from the levels of Eu3+ ions [19] as shown in the inset of Fig. 5. The emission spectra of Eu3+ doped SiO2 gels prepared at 50℃, 1 bar; and 150℃, 120 bars, were shown in Fig. 5. For recording the PL spectra the excitation energy has been fixed as 395 nm which is the 5L6 level of Eu 3+ ligand band. The PL from the Eu3+ doped SiO2 gel prepared at atmospheric pressure (1 bar) and 50℃ was found to be weak and inefficient for any practical application, whereas the PL intensity from the gel turn out to be much stronger (>10 times) when the sol was gelled under high temperature (150℃) and pressures (120 bars) inside an autoclave. Moreover, the PLE spectrum also became narrower under auto- clave treated gel sample, which indicate that there is a remarkable decrease in unsatisfied chemical bonds in the final product. The most intense line at ∼611 nm corresponds to the hypersensitive transition between the 5D0 and 7F2 level of the Eu 3+ ions and will be rel- atively strong if the surrounding symmetry is low. In the sense, it is generally admitted that the ratio of the emission intensities R=I(5D0 → 7F2)/I( 5D0 → 7F1) is an asymmetry parameter for the Eu3+ sites and a mea- sure of the extent of its interaction with the surround- ing ligands [20]. This indicates that the environment of the Eu3+ is dictated by the nano-SiO2 host under high pressure and temperature conditions. In addition, broad excitation peaks observed between 250-500 nm became distinct and sharp for the sample made under high pressures. The sharp peaks in the PL and PLE spectra of SiO2:Eu nanospheres may be due to quantum confinement effects related to size restrictions. A com- bination of unique features of high surface-to-volume ratios, monodispersion and strong photoluminescence suggest that these silica nanospheres will find many in- teresting applications in semiconductor photophysics, inorganic light emitting diodes, solar cells, environmen- tal remediations and optoelectronic devices. 150°C, 120 bar 50°C, 1 bar 20 15 10 5 0 E n er g y , 1 0 3 c m _ 1 Energy levels of Eu3+ 5DJ 5D0 _7F2 5D0 _7F1 5D0 _7F0 5D0 _7F3 λex=395 nmλem=611 nm X10 PLE 30 20 10 0 250 500 625 Wavelength (nm) 375 X10 7FJ J=2 J=0 J=6 J=0 PL In te n si ty ( a rb .u n it s) Fig. 5 PLE and PL spectra of SiO2:Eu gels made at (a) 50℃, 1 bar and (b) 120 bars and 150℃, respectively. Inset shows the mechanism of Eu3+ transitions. Conclusions In conclusion, we have demonstrated a mechanism by which photoluminescence enhancement in SiO2:Eu 3+ phosphor nanospheres could be successfully achieved using pressure-assisted sol-gel method. The observed red emission is from typical 5D0− 7F2 transition of Eu3+ and is found to be almost ten times brighter than the gel made at atmospheric pressure (1 bar) and ∼50℃ using Stöber-Fink-Bohn process. This kind of process is highly desirable for many crystalline and non- crystalline materials system wherein the doping is inap- propriate. This may lead to design many fundamental and novel optoelectronic applications. Acknowledgments The authors (DH, SM and SS) gratefully acknowl- edge the Department of Science and Technology (DST), Ministry of Science and Technology, Government of In- dia for their respective fellowships under various spon- sored projects to carryout the work. 144 Nano-Micro Lett. 3 (3), 141-145 (2011)/ http://dx.doi.org/10.3786/nml.v3i3.p141-145 References [1] J. Wang, Y. Yoo, C. Gao, I. Takeuchi, X. Sun, H. Chang, X. D. Xiang and P. G. Schultz, Science 279, 1712 (1998). [2] L. S. Liao, X. M. Bao, X. Q.Zheng, N. S. Li and N. B. Min, Appl. Phys. Lett. 68, 850 (1996). http://dx. doi.org/10.1063/1.116554 [3] M. A. Silva, D. C. Oliveira, A. T. Papacidero, C. Mello, E. J. Nassar, K. J. Ciuffi, and H. C. Sacco, J. Sol-Gel Sci. Tech. 26, 329 (2003). [4] E. J. Nassar, C. R. Neri, P. S. Calefi and O. A. Serra. J. Non-Cryst. Solids 247, 124 (1999). http://dx.doi. org/10.1016/S0022-3093(99)00046-0 [5] A. S. Zyubin, Y. D. Glinka, A. M. Mebel, S. H. Lin, L. P. Hwang and Y. T. Chen, J. Chem. Phys. 116, 281 (2002). http://dx.doi.org/10.1063/1.1425382 [6] Y. D. Glinka, A. S. Zyubin, A. M. Mebel, S. H. Lin, L. P. Hwang and Y. T. Chen, Euro. Phys. J. D 16, 279 (2001). http://dx.doi.org/10.1007/s100530170110 [7] D. Haranath, N. Gandhi, S. Sahai, M. Husain and V. Shanker, Chem. Phys. Lett. 496, 100 (2010). http:// dx.doi.org/10.1016/j.cplett.2010.07.015 [8] A. R. Guichar, D. N. Barsic, S. Sharma, T. I. Kamins and M. L. Bronersma Nano Lett. 6, 2140 (2006). [9] V. S. Kortov, A. F. Zatsepin, S. V. Gurbonov and A. M. Murzakaev, Phys. Solid State 48, 1273 (2006). http://dx.doi.org/10.1134/S1063783406070092 [10] D. Haranath, V. Shanker, H. Chander and P. Sharma, J. Phys. D: Appl. Phys. 36, 2244 (2003). http://dx. doi.org/10.1088/0022-3727/36/18/012 [11] C. J. Brinker and G. W. Scherer, Sol-Gel Science Aca- demic Press, Boston (1990). [12] J. C. G. Bunzil and G. R. Choppin, Lanthanide Probe in Life, Chemical and Earth Sciences, Elsevier, New York (1989). [13] D. Levy, R. Reisfeld and D. Avnir, Chem. Phys. Lett. 109, 593 (1984). http://dx.doi.org/10.1016/ 0009-2614(84)85431-7 [14] D. Haranath, S. Sahai, S. Singh, A. G. Joshi, M. Hu- sain and V. Shanker, J. Mater. Chem. 21, 9471 (2011). http://dx.doi.org/10.1039/c1jm11874a [15] S. Frank, P. Poncharai, Z. L. Wang and W. A. de Heer, Science 280, 1744 (1998). http://dx.doi.org/ 10.1126/science.280.5370.1744 [16] A. P. Alivisatos, Science 71, 933 (1996). [17] P. Kim and C. M Lieber, Science 286, 2148 (1999). http://dx.doi.org/10.1126/science.286.5447. 2148 [18] W. Han, S. Fan, Q. Li and Y. Hu, Science 277, 1287 (1997). http://dx.doi.org/10.1126/science. 277.5330.1287 [19] L. Xu, B. Wei, Z. Zhang, Z. Lu, H. Gao and Y. Zhang, Nanotechnology 17, 4327 (2006). [20] Z. Andric, M. D. Dramicanin, V. Jokanovic, T. Dram- icanin, M. Mitric and B. Viana, J. Optoelecton. Adv. Mater. 8, 829 (2006). [21] X. L. Wu, G. G. Siu, S. Tong and D. Feng, Appl. Phys. Lett. 69, 523 (1996). http://dx.doi.org/10.1063/1. 117774 [22] V. Lehmann and U. Gosele, Appl. Phys. Lett. 58, 856 (1991). http://dx.doi.org/10.1063/1.104512 [23] W. J. Zhang, X. L. Wu, J. Y. Fan, G. S. Huang, T. Qiu and P. K. Chu, J. Phys. Condens. Matter 18, 9937 (2006). http://dx.doi.org/10.1088/0953-8984/18/ 43/015 145 Introduction Experimental Results and discussion Conclusions Acknowledgments References