key: cord-0004338-ncqytz7t
authors: Yung, Pun To; Lester, Elizabeth; Ponce, Adrian
title: Quantitative and Fast Sterility Assurance Testing of Surfaces by Enumeration of Germinable Endospores
date: 2020-01-16
journal: Sci Rep
DOI: 10.1038/s41598-019-57175-3
sha: 9f667607bb77a0ba7d193d2426e96aa34d449a70
doc_id: 4338
cord_uid: ncqytz7t

A fast Endospore Germinability Assay (EGA) was validated with traditional plate counts to enumerate single endospore germination events for monitoring surface sterilization. The assay is based on a time-gated luminescence microscopy technique enabling visualization and enumeration of individual germinating endospores. Germinating endospores release calcium dipicolinate to form highly luminescent terbium dipicolinate complexes surrounding each germinating endospore. EGA and heterotrophic plate counting (HPC) were used to evaluate the swab/rinse recovery efficiency of endospores from stainless steel surfaces. EGA and HPC results were highly correlated for endospore recovery from stainless steel coupons inoculated with range of 1,000 endospores per coupon down to sterility. Dosage-dependent decrease of surface endospore germinability were observed in dry heat, UV irradiation, oxygen plasma and vaporized hydrogen peroxide treatments, measured with EGA and HPC. EGA is a fast and complementary method to traditional HPC for quantitative sterility assurance testing of surfaces. This work introduces and validates a 15-minute or faster assay for germinable endospores to complement the conventional lengthy, culture-based surface sterility validation, which is critical in hospitals, food and pharmaceutical industries to help minimize nosocomial infection, food spoilage, and pharmaceutical contamination.

Germination and culturing as a measure of endospore viability. The Endospore Germinability Assay (EGA) is based on the earliest observable mechanistic steps of dormant endospores reentering the active life cycle as observed by DPA release during stage I germination. By comparison, ATP assays probe at stage II germination and culturing probes after 20 or so replication cycles. None of these methods directly probe the viable population. Defining viability for microorganisms is neither simple nor straightforward 51 . Endospores that give rise to colonies on growth media are clearly viable, and this is generally considered a reliable approach to demonstrating viability. However, culture-based methods often overlook more than 99% of the viable-but-not-culturable (VBNC) population of cells in environmental samples [52] [53] [54] , effectively representing a conservative lower limit estimate of viability. In contrast, germination accounts for a greater fraction of viable organisms, but may include a subset population of germinable-but-not-viable endospores. As a complement to culturability, however, germination may be considered an upper limit on the viable number of endospores. While germination is a process that is nutrient-induced, and nutrients supplied may not cause all spores to germinate 55, 56 , we have demonstrated the reproducible correlation of germination-capable populations to culturable populations within lab spore suspensions, and that this correlation can be extended to spore inactivation studies 39, 57 . Therefore, trends observed in germinability can be used as a good indication of trends in viability, along with assigning an upper limit to the viable population.

Quantification of all viable biomass, as defined as having the ability for metabolic activity and reproduction, in an environmental sample, is currently difficult to achieve. Nonetheless, the culture-based assays and the Endospore Germinability Assay may be used in parallel to map out upper and lower limits of viability, thus allowing a bounded estimate of viability.

The application of EGA for sterility assurance of surfaces may be implemented by measuring the reduction in germinable endospore populations before versus after surface sterilization regimen are applied, which provides a measure of sterility assurance level. While endospore presence on surfaces are generally ubiquitous, a mixed population of environmental endospores may include species that are not readily germinable on the EGA experiment time scale with the germinants supplied. This concern may be mitigated by a broad spectrum germinant solution and extending the EGA observation time. Alternatively, fully characterized, bioindicator endospore populations may be used on surfaces to assess sterilization effectiveness with EGA. Additional characterization of EGA applied to surface sterility assurance with various sterilants and environments will provide improved guidelines for appropriate use of EGA for a range of applications.

Recovery of endospores from test surface coupons of stainless steel. Coupon surfaces were inoculated with a range of total spore populations as determined by phase contrast microscopy (0, 0.3, 1, 3.2, 10, 31.6, 100, 317, 1000 spores/coupon), of which 48% were germinable and 28% were culturable. The coupon surfaces were swabbed, rinsed and assayed by both EGA and HPC. Endospore recovery percentages (%R) were determined to be 36.3 ± 7.6% for EGA (%R EGA ) and 19.8 ± 7.2% for HPC (%R HPC ) (Fig. 1a) . EGA and HPC results were strongly correlated as determined by Spearman rank correlation coefficient (r s = 0.9321, p < 0.0001) on the entire data set. A scatter plot of EGA-HPC results and pairwise regression analyses (Fig. 1b) revealed a correlation coefficient of 0.965 across almost four orders of magnitude in concentration, as well as a strong linear correlation. The limit of detection (LOD) for endospore detection by EGA was calculated to be single endospores based on the fact that all signals had a signal-to-noise ratio (S/N) greater than or equal to 3. No false positives were recorded by either assay, as all sterile coupons gave zero counts.

The swab-and-rinse procedure consists of two major steps, where Step 1 is the transfer of endospores from the coupon surface to the swab head, and Step 2 is the transfer of endospores from the swab head into aqueous suspension by a series of vortexing and sonication. While step 1 is fundamentally difficult to assess empirically, we carried out an experiment on the recovery of endospores directly inoculated onto the cotton tip of a swab applicator. The inoculum population was 1,000 ± 67.5 endospores (n = 20, of which 48% were germinable and 28% were culturable). Table 1 shows that the recovery efficacies measured by EGA was 92.7 ± 9.2% and TSA HPC was 86.8 ± 13.8%.

Thermal inactivation of B. atrophaeus endospores. Figure 2a shows semi-logarithmic survival graphs of B. atrophaeus endospores laden on stainless steel coupons subjected to dry heat inactivation at 105 °C as measured by EGA and HPC. Survival graphs showed significant reduction of viable endospore counts with increasing thermal treatment time. The coupon was rendered sterile as measured by both EGA and HPC after 60 minutes at 105 °C (>7 log reduction). Survival graphs measured were fitted to both log-linear and Weibull distribution models. The kinetics and goodness-of-fit parameters are shown in Table 2 . The survival graph measured by EGA www.nature.com/scientificreports www.nature.com/scientificreports/ showed a sigmoid curve with a noticeable 18-min shoulder and tail, while the HPC graph showed log linear decay of endospore viability. To verify the existence of shoulder on the EGA graph, 6 data points were taken within the initial 10 min. The EGA D-value was calculated based on the log-linear portion of the EGA sigmoidal inactivation graph, which yielded a D-value of 25.6 ± 3.2 min and t C of 14.7 ± 2.1 min. The HPC inactivation graph yielded a D-value of 3.4 ± 0.6 min and t C of 2.64 ± 0.3 min. The HPC inactivation graph measured showed upward concavity, which indicates that at least two populations of endospores were present, with one that was inactivated at a relatively fast rate leaving behind survivors with a higher resistance. www.nature.com/scientificreports www.nature.com/scientificreports/ Ultraviolet inactivation of B. atrophaeus endospores. Figure 2b shows the inactivation graphs of B. atrophaeus endospores air-dried on stainless steel coupons, subjected to 254-nm irradiation with a power of 22.9 µW/cm 2 . EGA and HPC were employed to enumerate the surviving endospore fractions. Survival graphs were fitted to both the log-linear and Weibull models. EGA measured an inactivation curve with downward concavity, while HPC generated an inactivation curve that followed a log-linear pattern with a slight upward concavity. The EGA and HPC inactivation curves show substantial differences, which indicates that germination stage Imechanisms are less susceptible to UV inactivation than replication mechanisms. Sterility was achieved after 80 min of ultraviolet irradiation as measured by both assays. EGA measured a D-value of 12.4 ± 4.5 min and t C of 6.9 ± 0.5 min. HPC measured a D-value of 11.6 ± 3.8 min and t C of 6.1 ± 0.3 min.

Oxygen plasma inactivation of B. subtilis endospores. Figure 2c shows survival graphs of B. subtilis endospores inactivated by oxygen plasma. EGA and HPC both yielded first-order exponential inactivation kinetics from 0 to 30 min with good fitting to both log-linear and Weibull distribution plots. A rapid loss in germinability and culturability was observed after 30 min of exposure. The two methods were highly correlated with a correlation coefficient of 0.9997. EGA measured a D-value of 14.0 ± 1.6 min and t C of 14.2 ± 1.2 min. HPC measured a D-value of 16.9 ± 4.0 min and t C of 17.2 ± 2.3 min. The survival curve showed a significant reduction of the viable endospore count for increasing plasma inactivation time. The Weibull shape parameters, β, were very close to 1 in both cases because of the log-linear shape of the inactivation graphs.

Vaporized hydrogen peroxide inactivation of G. stearothermophilus endospores. Figure 2d illustrates the inactivation data of G. stearothermophilus endospores as a function of vaporized hydrogen peroxide treatment time. The data were fitted to log-linear and Weibull distribution models. Similar to the oxygen plasma inactivation case, the two inactivation graphs were both of a log-linear shape, sharing very similar model parameters. The coefficients of determination values were both 0.99 and 0.99 for EGA and HPC, respectively. The results obtained by both methods were highly correlated with a correlation coefficient of 0.9998. EGA measured a D-value of 12.7 ± 0.7 min and t C of 12.5 ± 1.0 min. HPC measured a D-value of 13.4 ± 0.8 min and t C of 13.2 ± 1.1 min.

When sterilization processes are evaluated using CFU inactivation of endospores (i.e., HPC), at least 2 days of incubation are required before results become available. Such a gap between sampling and results is undesirable for bioburden reduction or sterility assurance applications 58 . EGA provides the fastest possible biodosimetry, because it probes at the earliest stage of germination, and shows results on the timescale of minutes. We showed that EGA and HPC are reproducibly correlated in measuring endospores recovery efficiency from stainless steel coupons, and for measuring inactivation of endospores attached on stainless steel coupons with heat, ultraviolet radiation, vaporized hydrogen peroxide and oxygen plasma. EGA inherently measures a higher number of viable endospore than culture-based assays, because of the presence of germinable-but-not-culturable populations that are more resilient, which makes EGA a more conservative measure than HPC for sterility assurance. These populations arise because there are more mechanistic steps required in replication that can be targets for inactivation than those required for stage I germination. EGA is a fast, quantitative and complementary biodosimetry method to the traditional culture-based assays in sterility assurance testing of surfaces.

Chemicals. The methods used were described first in a Caltech thesis 59 . Terbium (III) chloride hexahydrate, 99.999%, L-alanine, DPA, and other salts were purchased from Sigma (St. Louis, MO) and were used as received. Agarose (>90%) was purchased from Invitrogen (Carlsbad, CA). Tryptic soy agar (TSA), nutrient broth and agar were obtained from Becton, Dickinson and Company (Sparks, MD). Calcium dipicolinate was prepared as previously reported 60 . Poly-dimethylsiloxane (PDMS) was obtained from Dow Corning (Edison, NJ). Endospore cultures. Geobacillus stearothermophilus ATCC 7953 was obtained in the form of filter paper inoculated with an endospore population of 1.8 × 10 6 CFU per strip from Steris Corporation (Mentor, OH). Bacillus subtilis ATCC 27370 endospores were prepared as previously described 61 www.nature.com/scientificreports www.nature.com/scientificreports/ tryptic soy broth (TSB) at 37 °C for 36 h. Vegetative cells in the exponential growth phase were inoculated into a sporulation medium consisting of 1.6% nutrient broth, 1.5% agar, 0.2% KCl and 0.05% MgSO 4 with filter-sterilized 1 mmol l −1 Ca(NO 3 ) 2 , 100 µmol l −1 MnCl 2 , 1 µmol l −1 FeSO 4 , and 0.1% glucose. The sporulating culture was incubated at 37 °C for 5 days. Following an overnight lysozyme digestion at 37 °C, endospores were purified from vegetative cell and cell debris by repeated centrifugation at 15,000 x g for 15 min at 4 °C and washing until 99.9% fully refractile bodies was obtained under phase contrast microscopy.

Bacillus atrophaeus ATCC 9372 was obtained in endospore suspension from Raven Biological Laboratories, Inc. (Omaha, NE; now Mesalabs, Inc.), with a concentration of 2.3 × 10 10 CFU ml −1 . Total endospore concentrations were determined using a Petroff-Hausser hemocytometer (Horsham, PA) and CFU concentrations were determined using TSA HPC in triplicate measurements. Endospore suspension was stored at 4 °C in the dark before use. Before each germination experiment, endospore samples were centrifuged at 8000 × g for 20 min and washed twice to remove excess dipicolinic acid in the supernatant. No significant difference in the stock CFU population was observed before and after heat shock treatment at 80 °C for 15 min. The heat shock process is a standard protocol for evaluating the bioburden level of flight hardware for planetary protection in NASA's robotic planetary missions as stated in the Handbook for the Microbial Examination of Space Hardware. The heat shock is used to kill vegetative cells, if present, and to activate the spores for germination.

Coupon preparation. Stainless steel 316 sheets (40″ × 80″) were procured and cut into 2″ × 2″ coupons in the machine shop at the California Institute of Technology (Caltech). Cotton applicators (Puritan, Guilford, ME) of length 15 cm were used to swab the coupon surfaces. Coupons were rinsed with 18.2 MΩ-cm deionized water and acetone to remove surface impurities and stains. They were cleaned with clean-room grade polyester wipes (BD Consumer Healthcare, Franklin Lakes, NY) saturated with 70% isopropyl alcohol. Each coupon was autoclaved at 121 °C for 15 min inside a glass Petri dish before inoculation. Endospore suspensions of B. atrophaeus were added aseptically and evenly on the coupons. evaporation and deposition were observed under a microscope to ensure minimal clumping, even spread and formation of monolayers of endospores. Care was taken not to drip over the edges. Coupons were air dried at room temperature inside a biological safety cabinet for 2 h and then further dried inside a Petri dish in a desiccator for 12 h in the presence of silica gel, and were used within 24 h Surface sampling. Each coupon was swabbed three times using a moistened sterile cotton applicator at an angle of 30° applying a firm pressure on the surface. The same swabbing procedure was repeated two more times with a 90° and 45° rotation of the coupon, respectively. Double swabbing is used to minimize variations in pressure, sampling time and moistening of cotton tip (Patterson, 1971) . The cotton head was aseptically broken off and placed into a tube containing 10 mL of sterile water. Cells were dislodged from the swab by 10 seconds of vortexing and 2 min of sonication at 25 kHz. The sample underwent heat shock at 80 °C for 15 min. Endospore strips of G. stearothermophilus and PDMS inoculated with B. subtilis were directly immersed into 10 mL of sterile water. The subsequent extraction and analysis processes were the same. A total of 30 samples at each inoculum population (0, 0.3, 1, 3.2, 10, 31.6, 100, 317, 1000 spore/coupon) were obtained on the stainless steel coupons. Germinable EGA counts were determined in replicates of 8 per coupon and culturable counts were determined in replicates of 6 per coupon, i.e., a total of 240 EGA measurements and 180 samples for culture assay.

Enumeration of germinable endospores. Samples were filtered onto 1.5-mm 2 spots on 0.2-µm polycarbonate membrane filters (Whatman, Florham Park, NJ) using a 96-well micro-sample filtration manifold (Schleicher and Schuell, Keene, NH). Endospores concentrated on the filter were transferred to a ~0.5 mm thick, 9 mm diameter slab of 1.5% agarose substrate containing 100 µmol l −1 TbCl 3 and 20 mmol l −1 L-alanine mounted in a silicone isolator (Molecular Probes, Eugene, OR) on a quartz microscope slide. After transfer of endospores, the agarose surface was covered with a piece of 0.2-mm-thick PDMS (Dow Corning, Midland, MI), prepared by mixing the polymer base and curing agent in a 10 to 1 ratio by weight. After degassing, the mixture was casted over a 0.2-mm thick stainless steel mold and cured in an oven for 2 h at 65 °C. Agarose, silicone isolator and PDMS were autoclaved at 121 °C for 15 min before use. A piece of PDMS was peeled off and attached on top of an endospore-laden agarose surface aseptically for sealing. Time-lapse gated images were collected by real-time streaming with a delay of 100 µs and exposure time of 5 s in each frame using a previously reported EGA instrumentation 39 .

Enumeration of culturable endospores. Culturable counts were determined by HPC on tryptic soy agar (TSA). B. subtilis and B. atrophaeus endospores were incubated at 37 °C. G. stearothermophilus endospores were incubated at 55 °C, CFU counts were recorded after 72 h of incubation.

Heat inactivation. In the dry heat inactivation experiment, B. atrophaeus endospores inoculated on stainless steel coupons were heat treated in an oven at 105 ± 0.5 °C. A beaker of silica gel was kept inside the oven. The time required to raise the coupon surface temperature to 105 °C was determined by a thermocouple and was added to each exposure cycle. Lethality of the process only included the holding period at 105 °C. Immediately after removal from the oven, each stainless steel coupon was chilled by ice. Endospores were sampled by the swab-rinse technique and enumerated by TSA HPC and EGA. D 105 °C was determined from a best-fit regression line of the data points by using a least square method. The variation of the data points around each regression line was measured by calculating the standard deviation of the estimate. UV inactivation. B. atrophaeus endospores laden on stainless steel coupons were contained in glass Petri dishes. They were exposed to continuous irradiation of UV from a 4 W low-pressure mercury lamp (UVP, Upland, CA) with peak irradiance at 254 nm (UVC) coupled with a 0.7-neutral-density filter. The distance between the UV lamp and the surface of the stainless coupon was 10 cm. The intensity at 254 nm was 60 µW cm −2 . The uniformity (2020) 10:431 | https://doi.org/10.1038/s41598-019-57175-3 www.nature.com/scientificreports www.nature.com/scientificreports/ of the lamp source had a maximum variation of ~4% within the irradiation area. The lamp was switched on 20 min before the start of the inactivation to stabilize the emission power and spectrum. Irradiation experiments were performed in a dark environment at room temperature without controlling the relative humidity. After irradiation, the samples were immediately chilled by ice at 0 °C. The swab-rinse method was used to suspend sampled populations, and the endospore surface concentration was determined by EGA and CFU enumeration. The protocol for monitoring UV inactivation of B. atrophaeus endospores in suspension was previously reported 39 .

Plasma inactivation. B. subtilis endospores were inoculated onto a 2 mm × 2 mm piece of PDMS placed on a glass microscope slide. The sample slide was placed within a glass vacuum chamber (150 mm radius and 300 mm length) at room temperature of a plasma system (Diener Electronics GmbH + Co., Germany). Low pressure was achieved using a vacuum pump. A radio frequency of 13.6 MHz was used to sustain the plasma. The endospore-inoculated glass slides were exposed to glow discharge at 100 W power for 0, 15, 30, 45, and 60 min. The RF generator was turned off immediately at the end of the inactivation process.

Vaporized hydrogen peroxide inactivation. Vaporized hydrogen peroxide (VHP) resistance of G. stearothermophilus ATCC 7953 (mean population = 1.8 × 10 6 CFU/coupon) on metal coupons was measured by EGA and culturability (colony formation on TSA). In a preliminary test, 0.5 mL of hydrogen peroxide was vaporized at 45 °C for 3 min in a chamber at Jet Propulsion Laboratory. 10 7 B. atrophaeus endospore/coupon and 1.8 × 10 6 G. stearothermophilus endospore/coupon were placed inside sterilization pouches and subjected to vaporized H 2 O 2 inactivation. In the VHP experiment, G. stearothermophilus endospores strips with different durations of vaporized H 2 O 2 inactivation treatment (0, 15, 30, 45, 60 min) were obtained from Steris Corporation using a LaCalhene two-glove isolator connected to a VHP1000ED system. G. stearothermophilus endospores were incubated and germinated at 37 °C and 55 °C, respectively. Data analysis. Phase contrast microscopy (PCM), Endospore Germinability Assay (EGA), and heterotrophic plate counts (HPC) were used to determine total endospore populations (P PCM ), germinable populations (P EGA ) and culturable populations (P HPC ), respectively, and these were used to derive the germinable fractions (P EGA / P PCM ) and culturable fractions (P CFU /P PCM ). Average percent recovery (%R) of endospores is calculated as follows:

HPC HPC(recovered)

Germinable and culturable populations were analyzed by using a logarithmic transformation. Average of the results were compared using the Mann-Whitney U-test. The correlation between endospore counts was analyzed by using a simple linear regression analysis and Spearman's rank correlation coefficient. A square root transformation was employed on the analysis of variance in the low concentration inoculum regime (<100 spores/coupon), where the endospore count followed a Poisson distribution. All data were analyzed at the 95% confidence level. Differences between mean values were calculated by Fisher's least significant difference (LSD) values, when appropriate. Differences were considered significant if p < 0.05. Inactivation models. Endospore survival graphs were constructed by plotting endospore numbers in logarithm versus inactivation times. The survival graphs were fitted to both Bigelow first-order model and Weibull distribution model. The Bigelow first-order model is given by:

where P 0 is the initial number of endospores and P is the number of endospores at time t measured immediately after the inactivation. Endospore inactivation results are reported in terms of both P EGA , and P CFU . Decimal reduction values (D-values) were calculated based on the log-linear portion of the plot. Endospore survival graphs were also fitted to the Weibull distribution model to better describe nonlinear features such as concavity, shoulders and tails 39 , which is given by:

where α is the scale parameter in time, and β is the dimensionless shape parameter. In a semi-logarithmic plot, the Weibull distribution corresponds to a concave upward survivor curve when β > 1, concave downward curve if β < 1, and is linear if β = 1. A parameter, t C , can be used to represent resistance or susceptibility towards certain inactivating agents, similar to the use of D-values in log-linear model.

where Γ is the gamma function. Goodness-of-fit was assessed using regression coefficient (R 2 ).

A Hundred Years of Medicine

Principles and Practice of Disinfection, Preservation and Sterilization

Next-generation approaches to understand and combat the antibiotic resistome

Different drugs for bad bugs: antivirulence strategies in the age of antibiotic resistance

The antibiotic resistome: the nexus of chemical and genetic diversity

Enhanced terminal room disinfection and acquisition and infection caused by multidrug-resistant organisms and Clostridium difficile (the Benefits of Enhanced Terminal Room Disinfection study): a cluster-randomised, multicentre, crossover study

Identifying opportunities to enhance environmental cleaning in 23 acute care hospitals

Impact of an environmental cleaning intervention on the presence of methicillin-resistant Staphylococcus aureus and vancomycin-resistant enterococci on surfaces in intensive care unit rooms

Reduction in acquisition of vancomycin-resistant enterococcus after enforcement of routine environmental cleaning measures

Biofilm Formation in Food Processing Environments is Still Poorly Understood and Controlled

A review of current and emergent biofilm control strategies

Microbial Stability of Pharmaceutical and Cosmetic Products

Validation Study on How to Avoid Microbial Contamination during Pharmaceutical Production

SP-2011-4234 Ch. Developing Effective Planetary Protection Approaches

Forward contamination of ocean worlds: A stakeholder conversation

Preventing the Forward Contamination of Europa

Structure and morphogenesis of the bacterial spore coat

The Bacillus subtilis endospore: assembly and functions of the multilayered coat

Germination of Spores of Bacillus Species: What We Know and Do Not Know

The heat resistance of bacterial spores

Microbiological Sampling of Surfaces

Microbiological monitoring of the food plant: Methods to assess bacterial contamination on surfaces

Biomarkers of bacterial spore germination

Comparison of results of ATP bioluminescence and traditional hygiene swabbing methods for the determination of surface cleanliness at a hospital kitchen

Validation and comparison of three adenosine triphosphate luminometers for monitoring hospital surface sanitization: A Rosetta Stone for adenosine triphosphate testing

Microcalorimetry: A novel method for detection of microbial contamination in platelet products

Principles of Bacterial Detection: Biosensors, Recognition Receptors and Microsystems

Comprehensive Guide to Steam Sterilization and Sterility Assurance in Health Care Facilities

Dependence of the heat resistance of bacterial endospores on their dipicolinic acid content

Relation of dipicolinic acid content of anaerobic bacterial endospores to their heat resistance

Relationship of dipicolinic acid content in spores of Bacillus cereus to ultraviolet and gamma radiation resistance

Resistance of Bacillus endospores to extreme terrestrial and extraterrestrial environments. Microbiol

Revival and identification of bacterial spores in 25-million-year-old to 40-million-year-old Dominican amber

Isolation of a 250 million-year-old halotolerant bacterium from a primary salt crystal

Microbiology for the Analytical Chemist

Fast sterility assessment with germinable endospore biodosimetry

Pulling the trigger: The mechanism of bacterial spore germination

The trigger mechanism of spore germination: Current concepts

The destruction by microwave radiation of bacterial endospores and amplification of the released DNA

Bacterial spore detection by [Tb 3+ (macrocycle)(dipicolinate)] luminescence

Chemical germination of native and cation-exchanged bacterial spores with trifluoperazine

Enhancement of Anion Binding in Lanthanide Optical Sensors

Terbium-Macrocycle Complexes as Chemical Sensors: Detection of an Aspirin Metabolite in Urine Using a Salicylurate-Specific Receptor Site

A Rapid Single Spore Enumeration Assay

Validation of a Clostridium Endospore Viability Assay and Analysis of Greenland Ices and Atacama Desert Soils

Microbial life at −13 degrees C in the brine of an ice-sealed Antarctic lake

Rapid endospore viability assay of Clostridium sporogenes spores

Survival Strategies Of Bacteria In The Natural-Environment

Phylogenetic identification and in situ detection of individual microbial cells without cultivation

Effect of Environmental-Factors on Estimated Viable and Total Populations of Planktonic Bacteria in Lakes and Experimental Enclosures

High Diversity in DNA of Soil Bacteria

The Bacterial Spore

Spore germination

Applications of a rapid endospore viability assay for monitoring UV inactivation and characterizing Arctic ice cores

Inactivation Of Clostridium-Difficile Spores By Disinfectants

Detection of aerobic bacterial endospores: from air sampling, sterilization validation to astrobiology

Mechanism of Ca 2+ and dipicolinic acid requirement for L-alanine induced germination of Bacillus cereus Bis-59 spores

Molecular Biology Methods for Bacillus

The research described in this paper was carried out at the Jet Propulsion Laboratory, California Institute of Technology, under a contract with the National Aeronautics and Space Administration. The authors thank DeAnn C. Dallas, Michael Kempf for helpful discussions, and Verrix, LLC for sponsoring publications costs.

P.T.Y. collected the data and prepared the manuscript. E.L. contributed to endospore preparation and collection of data. A.P. contributed to the study design and the preparation of the manuscript. All authors read and approved the final manuscript.

P.T.Y. and E.D.L. declare no competing interests. A.P. declares, in accordance his ethical obligation as a researcher, that he has a financial and business interests in a company that may be affected by the research reported in the enclosed paper. This research was sponsored by NASA and the Department of Homeland Security, and may lead to the development of products, the intellectual property of which are licensed to Verrix, LLC, in which A.P. has a business and financial interest. The research and draft manuscript was completed at NASA's Jet Propulsion Laboratory before the founding of Verrix, LLC, but the manuscript was not finalized and submitted until after Verrix, LLC was founded. This separation in time between when the research was performed, and the founding of Verrix, LLC, and the fact that the Jet Propulsion Laboratory Ethics Office documented the project ending prior to the foundation of Verrix mitigate even the perception of competing interests for this work.

Correspondence and requests for materials should be addressed to A.P.Reprints and permissions information is available at www.nature.com/reprints.Publisher's note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.