About the Author(s)


Sizwe Khoza symbol
Department of Logistics and Supply Chain Management, Faculty of Management Sciences, Vaal University of Technology, Vanderbijlpark, South Africa

Chengedzai Mafini symbol
Department of Logistics and Supply Chain Management, Faculty of Management Sciences, Vaal University of Technology, Vanderbijlpark, South Africa

Welby V. Loury Okoumba Email symbol
Department of Logistics and Supply Chain Management, Faculty of Management Sciences, Vaal University of Technology, Vanderbijlpark, South Africa

Citation


Khoza, S., Mafini, C. & Loury Okoumba, W.V., 2022, ‘Lean practices and supply-chain competitiveness in the steel industry in Gauteng, South Africa’, South African Journal of Economic and Management Sciences 25(1), a4617. https://doi.org/10.4102/sajems.v25i1.4617

Original Research

Lean practices and supply-chain competitiveness in the steel industry in Gauteng, South Africa

Sizwe Khoza, Chengedzai Mafini, Welby V. Loury Okoumba

Received: 11 April 2022; Accepted: 30 Aug. 2022; Published: 28 Oct. 2022

Copyright: © 2022. The Author(s). Licensee: AOSIS.
This is an Open Access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract

Background: The steel industry in South Africa suffered significantly when imported steel took over the market and collapsed big players in the industry in the last decade. The industry requires new business models and paradigms to improve its supply-chain strategies and adopt international standards such as lean supply-chain management practices to become competitive.

Aim: In the study the relationships are investigated between lean supply-chain management practices, lean culture, and supply-chain competitiveness in the steel industry in Gauteng Province.

Setting: The study was conducted in the steel manufacturing industry in the Gauteng Province, South Africa.

Methods: In the study a quantitative method involving 265 supply-chain and operations managers and practitioners was employed. The Statistical Packages for Social Sciences (SPSS version 27.0) was used to analyse the data in which correlations and regression analysis were employed to test the research hypotheses.

Results: The results of the study showed that four lean practices, namely Just in Time, Total Quality Management, Strategic Partnerships and Waste Elimination, all predict the establishment of a lean culture. However, Human Resource Management was statistically insignificant. The results further showed that a lean culture predicts competitiveness in the steel supply chain.

Conclusion: The adoption of lean supply chain management in the steel industry is an essential contributor to its success.

Keywords: supply chain management; lean supply chain management; just-in-time; total quality management; strategic partnership; waste elimination; human resources; lean culture; supply-chain competitiveness; South African steel industry.

Introduction

The steel manufacturing industry is one of the most important sectors contributing to the highest South African Gross Domestic Product (GDP) growth in South Africa, with the top five steel-consuming industries contributing R600 billion to GDP (15% of the total) and employing more than eight million people. This was mainly linked to its overall productivity, estimated at about 65% (Organisation for Economic Cooperation and Development [OECD] 2020; Statistics South Africa 2018). It was thus a vital part of economic growth in the country (Alabi 2016). The steel manufacturing industry played a significant role in the national economy and the economies of other African states. These include Egypt, Mozambique, Tanzania, Zambia, Kenya, Uganda, Namibia, the DRC, Ghana, and Ethiopia. It created jobs for many South Africans (Du Toit 2014; Worldsteel 2020).

The South African steel industry has been declining constantly since 2010. Challenges prevalent in the sector range from structural problems and persistent excess capacity to market demand negatively impacting trade and employment (Department of Trade and Industry 2018). The effects of the steel crisis are evident across the value chain, from mining primary steel mills to domestic manufacturers struggling to compete, sustaining jobs and the decline in domestic primary steel-production competitiveness (Schoeman, Oberholster & Somerset 2021; Van der Walt 2012).

The emergence of the coronavirus disease 2019 (COVID-19) pandemic worsened the situation in the steel industry, especially the implementation of government lockdown measures intended to save lives. The Trade and Industrial Policy Strategies (TIPS 2020) reported that the lockdown measures had devastating consequences for the steel sector, with an estimated R1bn being lost in direct cash-flow revenue and labour costs. Evidence of that is South Africa’s most important steel-producing company ArcelorMittal, which reported a drop in sales of about 40% due to the national lockdowns (ArcelorMittal South Africa 2020). Further affecting the steel sector is the volatility of the economic environment in the country, characterised by a recession. Also, the sector faces other operational challenges. Among the prominent ones is the inconsistency of direct supply, which could be attributed to a lack of supply-chain competitiveness (SCC) (Hannemann 2014; Motebele 2018).

The inconsistency in supply has resulted in supplier/customer distrust. The inconsistencies in the supply chain could have been caused by the ineffective application of several lean supply-chain management practices such as just-in-time (JIT), total quality management (TQM), strategic partnership (SP), waste elimination (WE) and human resources (HR). Kumar Singh and Modgil (2020) considered that these practices may enhance SCC through their influence on many firms’ lean culture. To solve the supply-chain crisis in South African steel manufacturing, firms have been trying to adopt new business initiatives to succeed in a unique and competitive marketplace (Khuluse 2015; Viljoen 2015). Lean supply-chain management (SCM) is an initiative that focuses on practices that eliminate nonvalue-adding activities (Hosseini, Soltani & Mehdizadeh 2018; Małysa & Furman 2021). These practices comprise JIT, TQM, SP, WE and HR; and have been widely used in discrete industries such as automobile manufacturing, electronics, and appliances (Talib et al. 2020). The application of lean practices to a continuous-process industry, such as steel, has been limited (Conejo, Birat & Dutta 2020). It has been argued that this is because such an industry is inherently more efficient and the need for such improvement activities, therefore, relatively less. (Kumar, Singh & Sharma 2014; Van der Walt 2012). Hore (2019) opines that steel manufacturing firms need SPs to gain customers’ trust. This could improve the demand, ensuring that products are enhanced as incorporated in Deming’s system of profound knowledge (Deming 1986; Ochieng 2021). Given the current crisis experienced by steel manufacturers, this research aims to empirically investigate the influence of lean supply-chain management (LSCM) practices on lean culture and SCC.

Against the above backdrop, this study investigated the relationship between LSCM practices, lean culture and SCC in the steel industry in Gauteng Province. The specific objectives of the study are to (1) test the connection between LSCM practices and lean culture and (2) test the association between lean culture and SCC. The steel industry is an important driver of South Africa’s diversified economy, making continual research necessary to generate information for solving its problems. Moreover, the body of empirical knowledge applying LSCM practices to the South African steel industry is still limited. What is available, are studies by Domingo (2013), who looked at implementing lean techniques as drivers of on-the-shelves product availability in the South African food retail industry.

Also, Khuluse (2015) investigated the level of adoption of lean practices among South African’ small and medium-size enterprises (SMEs). Viljoen (2015) established the strategic impact of selected lean factors on the operational performance of a selected South African gold plant. Dondofema, Matope and Akdogan (2017) provided a literature review study of the state of adoption of lean techniques in the broader South African economic environment. Fourie and Umeh (2017) focused on using lean factors in the maintenance environment. Lastly, Govender and Jasson (2018) explored the benefits and challenges of adopting lean practices as efficiency tools in the South African hospitality industry. However, the current study adopts a different approach in linking LSCM to SCC, a nexus that is fairly untested in the South African steel industry.

The article is organised as follows: The next section presents the review of the literature on the South African steel manufacturing industry and the respective constructs of the study. Thereafter, the conceptual model and hypotheses are presented, followed by the research methodology, data analysis and discussion of the results. The article concludes by providing theoretical and managerial contributions, limitations, and conclusive remarks.

Literature review

South African steel manufacturing industry

South Africa’s large, well-developed steel industry, with vast natural resources and a supportive infrastructure, represents roughly a third of all South Africa’s manufacturing. It comprises basic iron ore and steel, basic nonferrous metals, and metal products. The basic industries manufacture primary iron and steel products from smelting to semi-finished stages (Cape Gate Group of Companies 2019). Primary steel and semi-finished products include billets, blooms, slabs, forgings, reinforcing bars, railway track material, wire rods, seamless tubes, and plates (Kariuki 2013). South Africa was the world’s 25th-largest crude steel producer in 2018, with an output of 6.8 million tons (Mt) (Department of Trade and Industry 2019). South Africa exported 2.7 Mt of semi-finished and finished steel products worth $2.4bn (R42. 272,341,933.68). The country produced 5.4 Mt of iron and exported 662.4 kilotons (kt) of iron worth $245.2 million (R4.318,969,071.50). The volume of basic iron and steel products produced increased by 1.6% between March 2019, while the sales value of these products at current prices, rose by 9% over the same period. High production costs, the inconsistent supply of electricity, and poor domestic demand continue to significantly impact the performance of local manufacturers and wholesalers of basic iron and steel (Statistics South Africa 2019). Steel manufacturing firms must consider the concept of competitiveness to survive in the global marketplace by fulfilling the customers’ requirements for high-quality and low-cost products (Kariuki 2013; Mondliwa, Goga & Roberts 2021). The industry is one of the most important sectors contributing to the highest GDP growth in South Africa. Together, the top five steel-consuming industries contribute R600bn to GDP (15% of the total) and employ more than 8 million people as of 2018 third quarter (Statistics South Africa 2018; Zalk 2021). It is thus a vital part of economic growth for the country (Alabi 2016; Kan, Mativenga & Marnewick 2020).

Moreover, the industry plays a significant role in the national economy and the economies of other African countries, including Egypt, Mozambique, Tanzania, Zambia, Kenya, Uganda, Namibia, the DRC, Ghana, and Ethiopia. It creates jobs for many South Africans (Du Toit 2014). Steelmaking remains a key strategic industry, contributing to the fiscus and job creation (Department of Trade and Industry 2019). Each tonne of steel produced, creates jobs and provides value by beneficiating natural resources. Steel is fundamental to manufacturing in South Africa and adds significant value, representing more than 190 000 jobs in the direct iron ore, steelmaking and fabrication industries. The steel manufacturers have the prospect of employing many in the nation’s labour force (Ocheri et al. 2017; Trollip, McCall & Bataille 2022). For example, ArcelorMittal employed more than 10 000 employees directly, while it will create employment for millions of South Africans indirectly through the upstream and downstream industries (ArcelorMittal South Africa 2019). This will further help to alleviate the persistent unemployment problem of the nation. As an essential element of industrialisation, the steel industries are vital for developing linkages with all other sectors of the economy.

Lean supply chain management practices

The first objective of lean management is to eliminate every kind of waste in the company to make the business more competitive, through good results about innovation, flexibility, cost, quality, and service (Kumar Singh & Modgil 2020; Rocha 2017). The seven forms of waste addressed by lean production include defects, overproduction, delays, transport, over-processing, inventory, and motion. Based on this, Henderson and Larco (2000) defined eight fundamentals of lean manufacturing to guide the implementation. These fundamentals are environmentally safe, orderly, clean, JIT, six sigma quality, empowerment, visual management and seeking perfection. These are the bases of lean thinking. Since then, many factors have been identified as lean manufacturing practices. However, this study focuses on JIT, TQM, SP, WE and HR as the lean practices influencing lean culture and ultimately leading to SCC. These practices contribute to SCC in various manufacturing sectors, especially within the steel industries. These practices are discussed in the sub-sections below.

Just-in-time

The concept of JIT is defined as an inventory management philosophy, aimed at reducing waste and redundant inventory by delivering products, components, or materials just when an organisation needs them (Sharma, Dixit & Qadri 2015). Just-in-time ensures that only what is required is produced, when necessary, at the right time and in the correct quantity (Khuluse 2015). Just-in-time is fundamentally the reduction of excess inventory (Khuluse 2015). It uses the pull system, and according to Simona and Cristina (2015), the pull system is the centre of any synchronised factory; it works by working backwards, using signals or cards to trigger or start production. Given the tight competition in the steel manufacturing industry, customers’ demands must be incorporated efficiently and in a way that cost effectiveness is recognised. Firms effectively implementing JIT principles have substantial competitive advantages over competitors that have not (Garcia-Buendia et al. 2021; Madanhire & Mbohwa 2016). Lastly, organisations that have applied JIT, have managed to gain a competitive edge, improve the quality of the products, and reduce waste (Juárez, Perez & Useche 2017; Mukwakungu et al. 2019; Wyk & Naidoo 2016).

Total quality management

Total quality management is defined as the sequential development of a product’s quality (Anvari, Ismail & Hojjati 2011). It is an approach in which all the employees work together to improve a product, process, and working environment. Its main aim is to ensure customer satisfaction (García-Alcaraz et al. 2021; Soni et al. 2013). Total quality management is required to conduct successful continual improvement programmes in the workplace or ‘Gemba Kaizen’, in Japanese lean terms, and embodies the concept of lean culture (Panuwatwanich & Nguyen 2017). Furthermore, it refers to management that can be characterised by its set of principles, practices, and techniques. These comprise customer focus, continual improvement, and teamwork, to name a few (Siva et al. 2016). Each principle is implemented through a set of practices or simple activities such as collecting customer information and analysing processes (Luburić 2013). Total quality management focuses on exceeding customers’ expectations, identifying problems, building commitment, and promoting open decision-making among workers (Cherrafi et al. 2016; Slack & Singh 2020). Besides, Abd-Elwahed and El-Baz (2018) found TQM to correlate with lean culture positively.

Strategic partnership

An SP is an arrangement between two companies or organisations to help each other, or work together, to make it easier for them to achieve the things they want to attain (Caspar-Terizakis & Yu 2016). Besides, a critical partnership with suppliers has organised efforts to create and maintain a network of qualified suppliers. This effort includes all activities needed to improve the current performance of suppliers (Mohanty & Gahan 2012; Tarigan & Siagian 2021). Also, SP with suppliers has been designed to link the strategic and operational capabilities of separate organisations with suppliers to help them achieve significant benefits (Elms & Low 2013). The main objective of this concept is to increase the functional capability desired supplier (Cacciolatti et al. 2020; Mohanty & Gahan 2012). A good relationship with business partners, including key customers, plays a vital role in the success of supply chain management practised by an organisation (Mumassabba et al. 2015). Information sharing with business partners enables organisations to make better decisions and act because of greater visibility (Elms & Low 2013). Well-managed strategic alliances and consolidation are essential to long-term sustainability, growth, and SCC (Cacciolatti et al. 2020; Mráček & Mucha 2011).

Waste elimination

In terms of the industry, waste is defined as anything that does not add any value to the end product from the customer’s perspective (Demeter & Matyusz 2011). Wastes are activities that add cost or time, but do not add value, consuming more resources (time, money, space, etc.) necessary to produce the goods or services that the customer wants (Pal & Kachhwaha 2013). Waste includes activities that add cost or time, but do not add value, consuming more resources (time, money, space, etc.) necessary to produce the goods or services that the customer wants (Panuwatwanich & Nguyen 2017). Also, Rocha (2017) posited that the first objective of lean is eliminating every kind of waste in the company to change the business into more competitive through good results in innovation, flexibility, cost, quality, and service. The primary work strategy opted for process improvement is applying lean principles in material handling in steel plants. This optimises operational performance (Kumar et al. 2014).

Human resources

Lean in HR is defined as driving waste out of organisations’ human resource function operation processes (Khan et al. 2013). Lean as enabled by human resources, refers to how the human-resource processes and functions help create lean success throughout the organisation. Adopting lean principles well beyond core manufacturing has dramatically changed many other corporate internal functions, including product development, supply chain management, and accounting (Brown et al. 2016). Past research suggests that an organisation’s employees can be a source of sustained competitive advantage and determine their organisations’ ultimate success (Njeri & Thuo 2014). Given the importance of people in organisations, most strategic HR departments consider the management of the competencies and capabilities of these human assets the primary goal (Karuoya 2014). It is generally accepted that firms can create a competitive advantage from HR and their management practices. Effective HR management generates a higher capacity to attract and motivate employees for good performance, and the benefits of having adequate and qualified employees are numerous (Carvalho, Alves & Lopes 2011; Mijatović, Uzelac & Stoiljković 2020).

Some examples are higher profitability, less rotation, higher product quality, lower costs in manufacturing and a faster acceptance and implementation of the organisational strategy. Organisational resources lead to a sustained competitive advantage when valuable, rare, and inimitable and have no substitute (Fahmi & Abdelwahab 2012; Tran & Vo 2020).

Lean culture

The concept of a lean culture is regarded as the inclusion and engagement of every employee in continual improvement (Miller 2011). Pakdil and Leonard (2014) described it as one of the four components of a successful lean implementation. They explained that lean implementation consists of four components: lean planning, lean concepts, lean tools, and lean culture. Organisations using traditional manufacturing methodologies have struggled to compete successfully with those adopting lean practices (Van der Merwe, Pieterse & Lourens 2014). However, lean success is mainly dependent on attaining a lean culture. Companies that utilise mass-production systems controlled by top-down management approaches find that the change to a lean system is dependent on a significant shift in organisational culture (Imre, Jenei & Losonci 2013; Miller 2011). Besides, Mann (2014) described the concept as one of the four components of a successful lean implementation and explained that it consists of four components, namely lean planning, lean concepts, lean tools, and lean culture. Moreover, organisations or manufacturing industries that have successfully instilled a lean culture within the organisation and workforce will consistently realise SCC, more innovative, team-directed solutions, lower employee turnover and more success at sustaining improvements (Jekiel 2020; Van der Merwe 2014).

Supply-chain competitiveness

The competitiveness of a firm’s value chain refers to the capability of the supply chain to deliver value to the customer to competitive advantage. Also, it is regarded as the ability of the supply chain to gain a competitive advantage compared to other competing supply chain/s (Antai 2011; Shang, Zhou & Van Houtum 2010). Furthermore, Segarra-Moliner, Moliner-Tena and Sánchez-Garcia (2013) assert that competition and rivalry currently exist between one supply chain and the other supply chain, rather than between two firms based on value delivered to the customer. Supply-chain competitiveness is considered an important tool in gaining a competitive advantage. Due to speedy technological innovations, globalisation, and widely-used information technology, SCC is necessary for firms to focus strategically (Deng et al. 2020; Rajagopal 2010).

Furthermore, SCC can be achieved by efficient delivery, customer satisfaction, a better quality of products, profitability, more responsiveness, shorter lead times, demand fulfilment, optimal facilities, etc. (Naqvi, Asim & Manzoor 2020; Verma & Seth 2011). Verma and Seth (2011) proposed a conceptual framework for SCC. It is described that effective competitiveness requires some input elements, and then SCC yields outcomes out of a supply chain. Furthermore, SCC requires agility, coordination, collaboration, cooperation, synergy among partners, mass customisation, customer orientation, process orientation, demand management, and strategic alliances (Sakuramoto, Di Serio & Bittar 2018). While SCC will yield outcomes like customer value, customer satisfaction, quickness in response to changes, innovation, improvement, profitability, and ultimately competitive advantage.

Conceptual framework

The study tested the conceptual framework presented in Figure 1.

FIGURE 1: Conceptual framework.

Hypotheses development

Impact of Just in time on lean culture

The social values and morals of the employees are major enablers of the JIT system (Sharma et al. 2015). Simplified production processes such as eliminating inventories and large lot sizes in excess, create a needless customer time-cycle delay. Masudin and Kamara (2018) investigated the links between the JIT practices, attempting, in particular, to determine how they are linked to lean culture. The results support the argument that JIT practices positively affect culture. Syed, Barlow and Syed (2018) also determined the association between JIT and culture. Finally, Li, Wu and Holsapple (2017) suggest that employees have a key role in implementing lean culture. However, the JIT processes may not be achieved without the employees’ compliance. Based on the provided discussion, the following hypothesis can be stated:

H1: There is a significant positive relationship between JIT and lean culture in the South African steel industry

Impact of total quality management on lean culture

The concept of TQM is one of the critical determinants in a successful lean culture (Gimenez-Espin, Jimenez-Jimenez & Martınez-Costa 2013). Many other scholars have also advocated this (Panuwatwanich & Nguyen 2017; Zairi 2013). It was also found that the failure of the TQM implementation primarily derives from the lack of integration of TQM and culture change. To nurture TQM implementation success, several researchers recommended the need for organisations to change their organisational culture (Baird, Hu & Reeve 2011; Gimenez-Espin et al. 2013). Also, Viljoen (2015) states that a favourable working environment correlates with strong business performance and proves that organisational culture directly impacts the business. In doing so, steel manufacturing organisations must systematically define and assess their organisational culture based on a well-developed framework or model. It is against this background that this study posits the following:

H2: There is a significant positive relationship between TQM and lean culture in the South African steel industry

Impact of strategic partnership on lean culture

Embedded in the theoretical ‘relational view’ of management, which supports the view that firms may gain and sustain competitive advantage by leveraging and accessing resources from outside the firm’s boundaries (Salimova, Vatolkina & Makolov 2014). The authors propose a theoretically underpinned model whereby cultural compatibility between strategic supply-chain relationships has the potential to lead to improved performance outcomes for each participant in the chain. The linkages and interdependencies between strategic supply-chain relationships and organisational culture are evident in the literature (McFarlin 2017; McKay 2014). For example, rationalisation of the supply base should result in a deepening of relationships, which highlights the importance of shared values such as trust cooperation between each supply-chain partner organisation (Henderson & Dhanaraj 2014). In addition, the focus on strategic relationships has been shown to require compatible cultures (Bendiek & Kramer 2010). This study proposes a theoretical framework whereby it is posited that strategic supply chain relationships can only be truly successful if lean-cultural fit is achieved. Hence the following hypothesis is posited:

H3: There is a significant positive relationship between SP and lean culture in the South African steel industry

Impact of waste elimination on lean culture

To achieve WE, and continual improvement, organisations need the attitude, culture, and capabilities to constantly improve and sustain themselves in the future (Puvanasvaran, Huihui & Norazlin 2014). It is an organisation that does not require a management initiative, a customer initiative, or a shareholder initiative to improve – it comes from the desire and the will of the people inside the organisation (Tang, Chen & Luo 2011). This requires a commitment throughout the organisation to improve and eliminate those obstacles that delay, prevent, or inhibit improvements (Miafodzyeva & Brandt 2013). Culture determines how people think and behave in any workplace. Establishing a WE culture within manufacturing is necessary for other WE initiatives, such as a waste management plan (Miafodzyeva & Brandt 2013). By establishing a WE culture, the firm creates an environment inducive to bright ideas, increased efficiency and reduced operating costs. Hence this study posited the following:

H4: There is a significant positive relationship between WE and lean culture in the South African steel industry

Impact of human resources on lean culture

Human resources and SCM importance has been recognised as a means in gaining competitive advantage in different industries (Bhaskar & Tilak 2013). Hence, integrating HR and SCM functions enables organisations to craft a unique strategy and increase the firm’s supply-chain performance. According to Jurcevic, Ivaković and Babić (2013) the primary purpose of performance management is to instil in the employees a desire for continual improvement, which is the foundation of lean transformation. Selective hiring practices for new employees allow the organisation to select individuals with the desired knowledge, skills, and values to support the organisation’s long-term lean transformation strategy (Brown et al. 2016). Besides, Khan et al. (2013) found a positive impact of HR management practices on supply chain management success. Lean transformation success depends on the extent to which HR within the organisation has been embracing the concept. Active support and participation in the transformation process to leanness may lead to higher organisational–culture success rates (De Menezes, Wood & Gelade 2010). Hence, the study posited the following hypothesis:

H5: There is a significant positive relationship between HR and lean culture in the South African steel industry

Impact of lean culture on supply chain competitiveness

Organisations adopt lean operations principles either as a defensive strategy to stay competitive, or as an offensive strategy to move ahead of competitors (Nordin, Deros & Wahab 2010). Irrespective of adopting a lean approach, the actions required to become lean are the same, and the implementation process may be lengthy. Badurdeen, Wijekoon and Marksberry (2011) affirm that a similar lack of attention to lean culture also prevents South African steel manufacturers from realising the potential benefits of leanness. Moreover, Punnakitikashem, Buavaraporn and Chen (2013) conclude that lean culture is vital to any lean implementation plan’s success and that future research is required to create and maintain such a culture. The ill-defined nature of a lean organisational culture and time constraints caused by increased competition is exacerbated by this problem. Besides, Van der Merwe (2014) advanced that manufacturing industries must instil a lean culture in the organisation to attain an adequate level of competitiveness. In terms of innovative problem resolution, lower employee turnover and better success at sustaining improvements, amongst others. Finally, Miller (2011) and Imre et al. (2013) offered similar sentiments that lean-cultured organisations provide many benefits, including greater competitive advantages in supply chains. It is against this background that this study developed the following hypothesis:

H6: There is a significant positive relationship between lean culture and SCC in the South African steel industry

Research methodology

This study employed a positivist paradigm as its underpinning philosophy, because hypotheses were posited, and the study’s results are expected to be compared to the stated hypotheses. This is consistent with the objective of this study, which investigates the relationships between LSCM practices, lean culture and SCC, based on a conceptual framework with several quantifiable variables. Statistical methods are used to ascertain whether the framework fits the data. The methodology of the study is, thus, structured as follows:

Research sites and sampling method

The quantitative approach was selected since it facilitates results that can be generalised to other contexts. In this case, it was expected that the results of the study could be generalised to different contexts of steel-manufacturing companies throughout South Africa. This study followed a correlational research design, specifically a single cross-sectional survey, because data were collected only once from the sample elements (Burns, Veeck & Bush 2018). The cross-sectional strategy was chosen, because it provided inexpensive methods of collecting data over a large sample, and it pairs well with the quantitative method. The target population of this study comprised supply-chain and operations managers and practitioners from steel- manufacturing companies based in Gauteng Province. Confining the study to the province of Gauteng is justified by the fact that it is the most thickly populated region (12 564 000 habitants) and includes the most heterogeneous racial and ethnic groups (Statistics South Africa 2019). Moreover, most steel manufacturers are in Gauteng Province because of its large population. Lastly, the province is also known to be the country’s economic hub, which provides opportunities for current and future research. In terms of the sample frame, the lists of the supply chain and operation practitioners were obtainable from the HR databases of the steel manufacturing companies identified for this study.

Sampling procedure and technique

The list of steel manufacturing firms was obtained from the yellow pages and permission was sought from each of these firms. The final sample was composed of 265 respondents. This sample size was deemed acceptable based on two approaches. Firstly, the historical evidence approach was used, which focuses on previous similar studies. For example, Khuluse (2015) used a sample of n = 250 while Viljoen (2015) utilised a sample size of n = 115 for their quantitative studies on LSCM. The second approach was based on the sample size for multivariate studies as recommended by seminal scholars. In this regard, Pallant (2007) recommends a minimum of 150 respondents, and Tabachnick and Fidell (2007) propose a sample size of at least 200 cases for multivariate analysis. With these recommendations in mind, a total of 400 firms provided access to collect data from their supply-chain and operation managers and professionals. However, there was no sampling frame from which an accurate list of all targeted respondents could be drawn. As a result, a non-probability convenience sampling technique was applied to choosing the sample. Apart from the lack of an accurate sample frame, the respondents were not easily accessible due to the COVID-19 pandemic, making it necessary to use the convenience sampling technique. Supply-chain and operation managers and practitioners were contacted in person to complete the questionnaire.

Measures

All measurement instruments were anchored in a seven-point Likert scale ranging from 1 = strongly disagree to 7 = strongly agree. All constructs had 43-item scales adapted from Bortolotti, Boscari and Danese (2019) for JIT, SP, and HR. Sadikoglu and Olcay (2014) for TQM, Manzouri et al. (2014) for WE. Panuwatwanich and Nguyen (2017); Ganeshkumar and Nambirajan (2013) for lean culture and SCC, respectively. Appendix 1 provides the list of the measurement instruments in the study. All measurement scales had been validated in previous studies, having attained Cronbach alpha values above 0.7.

Field work

Data were collected through a survey using a structured questionnaire. The decision to make use of a questionnaire is influenced by the characteristics of the respondents the study intends to collect data from; the importance of reaching each targeted respondent; the importance of respondents’ answers not being contaminated or distorted; the size of the sample and the nature and the types of the questions (Saunders, Lewis & Thornhill 2016). Due to the outbreak of COVID-19, questionnaires were distributed to steel-manufacturing companies using two methods in this study. The first method was the drop-and-collect method, which involved the face-to-face distribution and collection of hard copies of the questionnaires to and from the available respondents at work. The second method involved email surveys. Emails were suitable since some respondents are geographically dispersed in the constituencies to be covered in this study. Many of the respondents worked from home, making it challenging to deliver questionnaires in the hard-copy format. Email addresses for such respondents were collected from their departments and used as a reference point for contacting them. Data collection took approximately four months and were conducted in the Vaal region between April and July 2020, in which 400 questionnaires were distributed. Upon their collection, the questionnaires were screened to determine their usability. However, some of the questionnaires were not returned, while some were incomplete due to a number of reasons. After systematically screening all questionnaires and discarding the incomplete ones, 265 were found usable, representing a 66.3% response rate.

Data analysis

The principal researcher captured the collected data on an excel spreadsheet. The data on the excel spreadsheet were cleaned by checking for missing entries. A statistician analysed the data using the Statistical Packages for the Social Sciences (SPSS 27.0). The basic statistical techniques applied in the study include descriptive statistics, normality tests, exploratory-factor analysis, correlations and regression analyses.

Sample profile

The majority of respondents were male (61.4%; n = 163). Regarding the age distribution of the sampled respondent, most respondents were aged between 34 and 41 years. Besides, 47.9% (n = 127) of the sampled population was Black-African. Also, 41.9% (n = 111) were holders of diploma qualifications. Regarding the respondents’ experience, 30.2% (n = 80) were employed between three to five years. Furthermore, 188 (71%) respondents were permanently employed. Lastly, 61.5% (n = 163) of the respondents were from the supply-chain management/procurement department.

Explanatory factor analysis

A Harman’s one-factor score test was conducted by running the preliminary explanatory factor analysis (EFA) on the sample data. In contrast, the unrotated factor solution was examined to determine the number of necessary factors to account for the variance in the variables. The single factor that emerged yielded one general factor accounting for approximately 24.89% of the covariance among the measures, concluding that common method variance is not a problem.

Table 2 presents the EFA results, performed using principal components analysis by applying Varimax rotation, which helped evaluate construct validity. The suitability of data for factorability was ascertained after examining the significant Kaiser-Meyer Olkin test statistic (KMO = 0.819) and the Bartlett sphericity test, which showed a significant result with a considerable chi-square value (χ2 = 8105.213; p ˂ 0.01). Most of the items loaded as expected with their factors, except for items SP3 and SP6 and HR5, which were discarded since they yielded weak and insignificant loadings on any of the extracted factors (below 0.50; p > 0.001). Table 1 presents the EFA’s results.

TABLE 1: Exploratory factor analysis results.
TABLE 2: Assessment of data normalcy.

The six lean principles remained unchanged, and the labelling remained the same (i.e. JIT, TQM, SP, HR, WE). Just-in-time had a KMO of 0.873, and all items explained 63.2% of the variance, while TQM had a KMO of 0.934 and explained 86.6% of the variance. Strategic partnership had a KMO of 0.786, explaining 79.5% of the variance. Waste elimination had a KMO of 0.895, with 78.4% of variance explained. Human resources had a KMO of 0.830, explaining 73.3% of the variance. Lean culture and SCC had KMO of 0.909 and 0.939 with 73.7 and 76.5 percentage of variance, respectively. All factor loadings were higher than 0.5, and commonalities were higher than the 0.3 minimum cut-off value.

Normality and common method bias assessment

In measuring normality, Field (2013) points out that the central limit theorem stipulates that the assumption of normality has little effect on data analysis for a large sample. Although the central theorem provides a studied theoretical background for the issue of normality in this study, the skewness and kurtosis of each construct and item are presented in Table 3. The value for skewness and kurtosis between -2 and +2 is considered acceptable to prove normal univariate distribution (Field 2013). Table 1 indicates that overall, the items of the scales have satisfactory skewness and kurtosis values. The Skewness values ranged from -0.848 to -1.711, while kurtosis ranged from 0.658 to 4.470. It can, therefore, be said confidently that the assumption of normality is met. Mardia (1974) suggests that the data is non-normal if about 80% of the data presented skewness and kurtosis above the recommended threshold of -3 to +3. The data were distributed normally in this study, and the conceptual model was not complex. This thus required the use-regression model to test the proposed relationships. Table 2 presents the assessment of data Normalcy.

TABLE 3: Correlation analysis of the constructs.
Correlation analysis

In this study, Pearson correlations were applied to test the strength and direction of relationships between the research constructs. The results are presented in Table 3.

Table 3 shows significant positive correlations between all research constructs. The strongest correlation occurred between lean culture and SCC (r = 0.712; p = 0.000). In contrast, the lowest correlation was found between HR and TQM (r = 0.388; p = 0.000). This indicates that a change increase in one construct will change the other constructs, either positively or negatively.

Regression analysis

In the current study, tolerance and the variance inflation factor (VIF), both regarded as measures of the impact of collinearity amongst the constructs in a regression model, were assessed, and should ideally be Tolerance > 0.1 and VIF < 10 (O’Brien, 2017:673). The values for all independent variables were within recommended limits and did not indicate any serious multicollinearity threat. The first multiple regression analysis tested JIT, TQM, SP, WE, and HR to determine if attitudes towards lean culture were predictors. It was found that JIT (Tol = 0.511, VIF = 1.958), TQM (Tol = 0.460, VIF = 2.175), SP (Tol = 0.503, VIF = 1.990) and WE (Tol = 0.549 VIF = 1.822) were significant predictors of lean practices towards lean culture. However, HR (Tol = 0.708, VIF = 1.412) did not predict lean practices toward lean culture. Table 4 reports the regression analysis between lean practices and lean culture.

TABLE 4: Regression analysis of lean practices and lean culture.

The predictor variables were the five lean practices (JIT, TQM, SP, WE, HR) (independent variable). The dependent variable that was entered into the prediction model was lean culture. Examining the relationship between lean practices and lean culture rating, the adjusted R2 = 0.483 indicates that lean practices combined, explained 48.3% of the variance in lean culture. Table 5 reports the regression analysis between lean culture and SCC.

TABLE 5: Regression analysis of lean culture and supply-chain competitiveness.

The predictor and independent variable held constant was lean culture, and the dependent variable was SCC. The rating (adjusted) of the relationship between the constructs was R2 = 0.507, indicating that lean culture explained 50.7% of the variance in SCC.

Assessment of measurement instruments (Reliability and validity results)

Table 6 presents the reliability results of the study, as indicated by the Cronbach alpha.

TABLE 6: Reliability results.

All scales attained Cronbach alpha values above the recommended 0.7 minimum threshold, which confirms that the scales were internally consistent.

To test for face and content validity of the measurement instrument, the questionnaire was reviewed by the research supervisors. Additionally, a pilot study was conducted, involving a convenient sample of 50 respondents. Feedback from the review and the pilot study was used to improve the questionnaire to make it more suitable for the final survey. The EFA procedure was used to test for construct validity (refer to Table 1), where factor loadings were higher than the 0.5 lower cut-off value, indicating that construct validity was adequate. Additionally, the positive correlation values (refer to Table 3) further confirmed that construct validity was acceptable. Figure 2 shows the conceptual model of the study incorporating the results of the hypotheses testing.

FIGURE 2: Path coefficient results.

Hypotheses tests results

Table 7 shows a rundown of the results from this research and states the decision relating to the hypotheses formulated for this study.

TABLE 7: Hypotheses decisions.

In Table 7, H2, H3, and H4 were supported, implying that TQM, SP, and WE significantly predicted lean culture. H6 was strongly supported with a Beta-value of 0.712, indicating a positive and significant relationship between lean culture and SCC.

Discussion of results

Regression analysis was used to test the direct causal relationships between the study constructs. The results revealed the following empirical observations. Regarding the association between JIT and lean culture, the implementation of the JIT solutions in the steel industry is not linked to establishing a lean culture or does not predict its improvement. This result contradicts previous studies by Wyk and Naidoo (2016:237) in the electronics manufacturing industry that showed that adopting JIT affects the extent to which lean thinking and the minimisation of waste become entrenched within the organisation. Sharma et al. (2015) also established the importance of JIT in lean manufacturing processes.

Furthermore, Masudin and Kamara (2018) deduced that JIT’s philosophy advocates the elimination of waste by simplifying lean production processes. The empirical evidence from this research highlights that TQM is a significant predictor of lean culture. This result aligns with a previous study by Sreedharan et al. (2016) and Cherrafi et al. (2016:828), who further established that effective TQM requires a lean system among people, machines, and information, stressing a systematic approach to quality. Strategic partnership was found to be an essential predictor of lean culture. This point was supported by Mumassabba et al. (2015), who stated that SP and lean culture yields better understanding among crucial stakeholders in supermarkets in Kenya. The significance of WE as a driver of lean culture was advocated by Demeter and Matyusz (2011). They established that WE plays a vital role in the implementation of a lean culture in the manufacturing industry. The results regarding human resources showed a positive relationship with lean culture. This was endorsed by Bhaskar and Tilak (2013), human resources do play a positive and significant role in the implementation of lean culture through employee engagement. In the study it is, therefore, deduced that employees are the most critical resource of the four resources required to bring about success in any form of organisation.

It can be concluded that employees who continually learn and enhance their skills become the organisations’ critical assets. This implies that organisations in the steel industry in Gauteng need to investigate HR and align them with the learning culture to more successfully adopt a lean culture. Finally, the result demonstrated that a lean culture exerts a positive and significant influence on SCC. This, thus means that the steel manufacturing firms with lean culture are more likely to achieve SCC. These findings align with Vanichchinchai’s (2019) observations in that the author established that lean practices positively influence supply-chain performance in terms of competitiveness and customer satisfaction. According to Van der Merwe (2014), manufacturing industries that have successfully instilled a lean culture in the organisation and workforce will consistently realise SCC, more innovative, team-directed solutions, lower employee turnover, and more success at sustaining improvements.

Theoretical contributions

This study proposed and empirically tested a conceptual model that incorporated LSCM practice (JIT, TQM, HR, SP and WE) as antecedents of a lean culture in the steel manufacturing industry. In addition, SCC was also incorporated as an outcome of lean culture. This model’s uniqueness is its holistic stance that posits six LSCM practices which directly impact lean culture and, ultimately, SCC. Finally, the resultant conceptual model proposed in this study would improve the supply-chain model related to the steel manufacturing industry; and researchers studying the supply chain for other industries could use the model.

Managerial contributions

Knowing more about the factors enhancing lean culture and improving SCC would help these firms create the right strategies to strengthen, enhance, and manage their supply chains. This study provides this much-needed information and indicates the extent to which steel manufacturing’s LSCM practices affect lean culture and SCC. This would guide the steel manufacturing firms to allocate their resources to improve their SCC appropriately. This study would also be helpful for businesses and decision-makers because it would provide insights into LSCM grey areas and help improve their business performance in South Africa and Africa as a whole.

Limitations and future research

In assessing the findings of this study, it should be noted that the study is by no means without limitations, which offers avenues for future research. Some of the main challenges that hampered the adequate completion of this investigation are that the study was confined to only steel manufacturing firms in Gauteng Province, specifically Southern Gauteng, where there is a market leader of steel producers in the country (ArcelorMittal South Africa). Studies (Mukhtar 2015) show that market leaders are more proactive in their business operations than their followers, as a result they may have been practising lean manufacturing for a more extended period. Another limitation is related to the research methodology employed. A survey using self-administrated questionnaires was employed in this study. While self-reporting may rightly gauge the LSCM practices influencing lean culture, the report on these practices may need implicit studies or experimental methods. The third limitation is that the study was cross-sectional in nature. This means that the reported results relate to only a particular point in time. Applying a cross-sectional design implies that the investigation has focused on reported lean practices, lean culture and SCC instead of emphasising observed changes in these variables over time. In future research a longitudinal survey and observation research focusing on uncovering LSCM practices affecting lean culture and SCC over a long period may be applied. For example, researchers may track SCC frequency should the firms improve their JIT, TQM, SP, WE and HR.

Conclusion

This study aimed to investigate the relationships between LSCM practices, lean culture, and SCC in the steel industry in Gauteng Province. It tested a conceptual model that incorporated LSCM practices (predictor variables) and lean culture (mediator variable) to understand the factors influencing SCC (outcome variable). It made theoretical contributions by developing and testing the conceptual model and understanding steel manufacturing’s supply chain. Practical contributions exposed areas where decision/policymakers and businesses could enhance their efforts in improving SCC in the steel manufacturing industry. The study opens avenues for future research to expand the findings obtained and deal with a few limitations. While the factors driving lean culture may help improve supply-chain performance, corresponding efforts should be made to increase the ineffective supply chains in South Africa and other parts of the globe.

Acknowledgements

Competing interests

The authors have declared that no competing interest exists.

Authors’ contributions

S.K. conducted the fieldwork of the study and wrote the research methodology section. C.M. performed the data analysis and wrote the results section. Lastly, W.V.L.O. wrote the initial section of the article and performed the literature review.

Ethical considerations

Ethical clearance to conduct the study was obtained from the Central Research Ethics Committee at a South African University of Technology. The study conformed to ethical standards regarding the minimal risk it posed and the voluntary participation and protection of respondents’ identity. It was further supported by providing an ethical clearance certificate conferred by the Vaal University of Technology (FRECMS-18032020-028 25264231 [30 April 2020]).

Funding information

The author(s) received no financial support for the research, authorship, and/or publication of this article.

Data availability

Data supporting the findings of this study are available from the corresponding author on request.

Disclaimer

The views and opinions expressed in this article are those of the authors and do not necessarily reflect the official policy or position of any affiliated agency of the authors.

References

Abd-Elwahed, M.S. & El-Baz, M.A., 2018, ‘Impact of implantation of total quality management: An assessment of the Saudi industry’, South African Journal of Industrial Engineering 29(1), 97–107. https://doi.org/10.7166/29-1-1902

Alabi, M.O., 2016, ‘Measuring the prevailing lean culture at a South African aviation organisation’, MTech dissertation, North-West University, Potchefstroom.

Antai, I., 2011, ‘A theory of the competing supply chain: Alternatives for development’, International Business Research 4(1), 1–145. https://doi.org/10.5539/ibr.v4n1p74

Anvari, A., Ismail, Y. & Hojjati, S.M.H., 2011, ‘A study on Total Quality Management and lean manufacturing: Through lean thinking approach’, World Applied Sciences Journal 12(9), 1585–1596.

ArcelorMittal South Africa, 2019, Local steel sector is the reinforcing in SA’s economy, viewed 15 November 2020, from http://Arcelormittal.co.za/report/aspa/.

ArcelorMittal South Africa, 2020, ArcelorMittal South Africa Integrated report 2019, viewed 05 October 2020, from https://southafrica.arcelormittal.com/Portals/0/ArcelorMittal%20AR_2019_Lores.pdf.

Badurdeen, F., Wijekoon, K. & Marksberry, P., 2011, ‘An analytical hierarchy process-based tool to evaluate value systems for lean transformations’, Journal of Manufacturing Technology Management 5(2), 85–99. https://doi.org/10.1108/17410381111099806

Baird, K., Hu, K.J. & Reeve, R., 2011, ‘The relationship between organisational culture, total quality management practices and operational performance’, International Journal of Operations & Production Management 31(7), 789–814. https://doi.org/10.1108/01443571111144850

Bendiek, A. & Kramer, H., 2010, ‘The EU as a would-be global actor: Strategic partnerships and interregional relations’, in J. Husar, G. Maihold & S. Mair (eds.), Europe and new leading powers, pp. 21–43, Nomos Verlagsgesellschaft mbH & Co. KG, Baden-Baden.

Bhaskar, N. & Tilak, R., 2013, ‘An analytical case study of an advanced manufacturing system for evaluating the impact of human enablers in its performance’, Journal of Advances in Management Research 10(1), 48–62. https://doi.org/10.1108/09727981311327785

Bortolotti, T., Boscari, S. & Danese, P., 2019, ‘Successful lean implementation: Organisational culture and soft lean practices’, International Journal of Production Economics 160, 182–201. https://doi.org/10.1016/j.ijpe.2014.10.013

Brown, A., Jasskiewicz, W., Mchenry, B., Meier, E. & Zwinkels, D., 2016, Building human resources for supply chain management: Theory of change, Technical Report, pp. 1–64, United States Agency for International Development (USAID) through the USAID Global Health Supply Chain Program, Washington, DC.

Burns, A.C., Veeck, A. & Bush, R.F., 2018, Marketing research, 8th edn., Pearson Education, Harlow.

Cacciolatti, L., Rosli, A., Ruiz-Alba, J.L. & Chang, J., 2020, ‘Strategic alliances and firm performance in startups with a social mission’, Journal of Business Research 106, 106–117. https://doi.org/10.1016/j.jbusres.2019.08.047

Cape Gate Group of Companies, 2019, Medium and high carbon wire for sophisticated applications, viewed 07 May 2020, from http://www.capegate.co.za/aboutus.asp.

Carvalho, R., Alves, A. & Lopes, I., 2011, ‘Principles and practices of lean production applied in a metal structures production system’, in Proceedings of the world congress on engineering, 06th–08th July 2011, London.

Caspar-Terizakis, C. & Yu, X., 2016, Definition, benefits and forms of strategic partnership – Best practice, TU Darmstadt-Tongji University, Shanghai.

Cherrafi, A., Elfezazi, S., Chiarini, A., Mokhlis, A. & Benhida, K., 2016, ‘The integration of lean manufacturing, Six Sigma and sustainability: A literature review and future research directions for developing a specific model’, Journal of Cleaner Production 139, 828–846. https://doi.org/10.1016/j.jclepro.2016.08.101

Conejo, A.N., Birat, J.P. & Dutta, A., 2020, ‘A review of the current environmental challenges of the steel industry and its value chain’, Journal of Environmental Management 259, 1–9. https://doi.org/10.1016/j.jenvman.2019.109782

De Menezes, L.M., Wood, S. & Gelade, G., 2010, ‘The integration of human resource and operation management practices and its link with performance: A longitudinal latent class study’, Journal of Operations Management 28(6), 455–471. https://doi.org/10.1016/j.jom.2010.01.002

Demeter, K. & Matyusz, Z., 2011, ‘The impact of lean practices on inventory turnover’, International Journal of Production Economics 133(1), 54–163. https://doi.org/10.1016/j.ijpe.2009.10.031

Deming, W.E., 1986, Out of the crisis, Massachusetts Institute of Technology, Center for Advanced Engineering Study, Cambridge, MA.

Deng, W., Feng, L., Zhao, X. & Lou, Y., 2020, ‘Effects of supply chain competition on firms’ product sustainability strategy’, Journal of Cleaner Production 275, 124061. https://doi.org/10.1016/j.jclepro.2020.124061

Domingo, T.M., 2013, ‘The adoption of lean techniques to optimise the on-shelf availability of products and drive business performance in the food industry: A South African manufacturing and retail case study’, Master’s thesis, University of Cape Town.

Dondofema, R.A., Matope, S. & Akdogan, G., 2017, ‘Lean applications: A survey of publications with respect to South African industry’, South African Journal of Industrial Engineering 28(1), 103–113. https://doi.org/10.7166/28-1-1660

Du Toit, D., 2014, ‘Engineering change management in a large steel manufacturing company’, Meng, dissertation, NWU, Potchefstroom.

Elms, D.K. & Low, P., 2013, ‘Global value chains in a changing world, WTO/FGI/TFCTN, WTO: World Trade Organisation, viewed 13 July 2020, from https://policycommons.net/artifacts/1135030/global-value-chains-in-a-changing-world/.

Fahmi, S.M. & Abdelwahab, T.M., 2012, ‘Case study: Improving production planning in steel industry in light of lean principles’, in Proceedings of the 2012 International Conference on Industrial gineering and Operations Management Istanbul, Istanbul, Turkey, 03–06 July, pp. 2489–2497.

Field, A., 2013, Discovering statistics using IBM SPSS statistics, Sage.

Fourie, C.J. & Umeh, N.E., 2017, ‘Application of lean tools in the supply chain of a maintenance environment’, South African Journal of Industrial Engineering 28(1), 176–189. https://doi.org/10.7166/28-1-1507

Ganeshkumar, C. & Nambirajan, T., 2013, ‘Supply chain management components, competitiveness and organisational performance: Causal study of manufacturing firms’, Asia-Pacific Journal of Management Research and Innovation 9(4), 399–412. https://doi.org/10.1177/2319510X14523109

García-Alcaraz, J.L., Montalvo, F.J.F., Sánchez-Ramírez, C., Avelar-Sosa, L., Saucedo, J.A.M. & Alor-Hernández, G., 2021, ‘Importance of organisational structure for TQM success and customer satisfaction’, Wireless Networks 27(3), 1601–1614. https://doi.org/10.1007/s11276-019-02158-5

Garcia-Buendia, N., Moyano-Fuentes, J., Maqueira-Marín, J.M. & Cobo, M.J., 2021, ‘22 years of lean supply chain management: A science mapping-based bibliometric analysis’, International Journal of Production Research 59(6), 1901–1921. https://doi.org/10.1080/00207543.2020.1794076

Gimenez-Espin, J.A., Jimenez-Jimenez, D. & Martinez-Costa, M., 2013, ‘Organisational culture for total quality management’, Total Quality Management & Business Excellence 24(5–6), 678–692. https://doi.org/10.1080/14783363.2012.707409

Govender, C.M. & Jasson, C.C., 2018, ‘Lean practices for efficiency in the South African hospitality sector’, African Journal of Hospitality, Tourism & Leisure 7(2), 1–14.

Hannemann, M., 2014, ‘Key strategic factors contributing to global competitiveness of the South African steel industry’, Master in Business Administration, University of Johannesburg.

Henderson, B.A. & Larco, L., 2000, Lean transformation: How to change your business into a lean enterprise, The Oaklea Press, Richmond, VA.

Henderson, J. & Dhanaraj, C., 2014, Strategic partnerships, International Institute for Management Development, pp. 1–4, viewed 17 June 2019, from https://www.imd.org/contentassets/8d81e92f7a5d4931805a0466143ea8c6/36---strategic-partnerships-final-20.05.14.pdf.

Heritage, B., Pollock, C. & Roberts, L., 2014, ‘Validation of the organisational culture assessment instrument’, PLoS One 9(3), 1–10. https://doi.org/10.1371/journal.pone.0092879

Hore, S., 2019, ‘Impact of barriers and enablers on effective lean implementation in Indian Steel industry’, doctoral dissertation, Indian School of Mines, Dhanbad.

Hosseini, A.S., Soltani, S. & Mehdizadeh, M., 2018, ‘Competitive advantage and its impact on new product development strategy (Case study: Toos Nirro technical firm)’, Journal of Open Innovation: Technology, Market, and Complexity 4(17), 1–12. https://doi.org/10.3390/joitmc4020017

Imre, N., Jenei, I. & Losonci, D., 2013, What is lean culture – And how to measure it?, Corvinus University of Budapest, Hungary.

Jekiel, C.M., 2020, Lean human resources: Redesigning HR processes for a culture of continuous improvement, Productivity Press, New York, NY.

Juárez, F., Perez, C.H. & Useche, A., 2017, ‘Just in time strategy and profitability analysis in financial statements’, in Proceedings of the International Conference on Industrial Engineering and Operations Management, 25th–26th October Bogota.

Jurcevic, M., Ivaković, M. & Babić, D., 2013, The role of human factors in supply chain, Wiley, NJ.

Kan, K., Mativenga, P. & Marnewick, A., 2020, ‘Understanding energy use in the South African manufacturing industry’, Procedia CIRP 91, 445–451. https://doi.org/10.1016/j.procir.2020.02.197

Kariuki, B.M., 2013, ‘Role of lean manufacturing on organisation competitiveness’, Industrial Engineering Letters 3(10), 81–82.

Karuoya, L.N., 2014, ‘Factors influencing sustainable competitive advantage among cut flower companies’, International Journal of Current Business and Social Sciences 1(1), 1–17.

Khan, N.R., Taha, S., Ghouri, A.M., Khan, M.R. & Yong, C.K., 2013, ‘The impact of HRM practices on supply chain management success in SME’, Scientific Journal of Logistics 9(3), 177–189. https://doi.org/10.2139/ssrn.2281372

Khuluse, S., 2015, ‘Survey on lean practices in Small and Medium Manufacturing Enterprises in KwaZulu-Natal, a province of South Africa’, MBA dissertation, University of KwaZulu-Natal, Durban.

Kumar, D., Singh, S.K. & Sharma, K., 2014, ‘Implementation of lean in continuous industry: A case study (Steel Industry)’, International Journal of Engineering Research and Applications 4(3), 5–12.

Kumar Singh, R. & Modgil, S., 2020, ‘Assessment of lean supply chain practices in Indian automotive industry’, Global Business Review 0(0), 1–39. https://doi.org/10.1177/0972150919890234

Li, X., Wu, Q. & Holsapple, C.W., 2017, ‘An empirical examination of firm financial performance along dimensions of supply chain resilience’, Management Research Review 40(3), 254–269. https://doi.org/10.1108/MRR-02-2016-0030

Luburić, R., 2013, ‘Total quality management as a paradigm of business success’, Journal of Central Banking Theory and Practice 3(1), 59–80. https://doi.org/10.2478/jcbtp-2014-0005

Madanhire, I. & Mbohwa, C., 2016, ‘Application of just in time as a total quality management tool: The case of an aluminium foundry manufacturing’, Total Quality Management & Business Excellence 27(1–2), 184–197. https://doi.org/10.1080/14783363.2014.969909

Małysa, T. & Furman, J., 2021, ‘Application of selected Lean Manufacturing (LM) tools for the improvement of work safety in the steel industry’, Metalurgija 60(3–4), 434–436.

Mann, D., 2014, Creating a lean culture: Tools to sustain lean conversions, 3rd edn, CRC Press, Boca Raton, FL.

Manzouri, M., Ab-Rahman, M.N., Zain, C.R.C.M. & Jamsari, E.A., 2014, ‘Increasing production and eliminating waste through lean tools and techniques for Halal food companies’, Sustainability 6(12), 9180–9204. https://doi.org/10.3390/su6129179

Mardia, K.V., 1974, ‘Applications of some measures of multivariate skewness and kurtosis in testing normality and robustness studies’, Sankhyā: The Indian Journal of Statistics, Series B 36(2), 115–128.

Masudin, I. & Kamara, M.S., 2018, ‘Impact of just-in-time, total quality management and supply chain management on organisational performance: A review perspective’, Journal Teknik Industry 19(1), 11–20. https://doi.org/10.22219/JTIUMM.Vol19.No1.11-20

Mcfarlin, K., 2017, How to propose a strategic partnership, viewed 12 November 2019, from http://smallbusiness.chron.com/propose-strategic-partnership-10483.html.

Mckay, K., 2014, How to create strategic partnerships that are a win-win, viewed 02 February 2021, from https://www.entrepreneur.com/article/234425.

Miafodzyeva, S. & Brandt, N., 2013, ‘Recycling behaviour among house holders: Synthesising determinants via a meta-analysis’, Waste and Biomass Valorisation 4(2), 221–235. https://doi.org/10.1007/s12649-012-9144-4

Mijatović, M.D., Uzelac, O. & Stoiljković, A., 2020, ‘Effects of human resources management on the firm manufacturing performance: Sustainable development approach’, International Journal of Industrial Engineering Management 11(3), 205–212. https://doi.org/10.24867/IJIEM-2020-3-265

Miller, L.M., 2011, Creating lean culture: How to apply best practices, viewed 02 March 2019, from http://www.lmmiller.com/wp-content/uploads/2011/06/Lean-Culture-Part-One1.pdf.

Mohanty, M.K. & Gahan, P., 2012, ‘Buyer supplier relationship in manufacturing industry – Findings from Indian manufacturing sector’, Business Intelligence Journal 5(2), 319–333.

Mondliwa, P., Goga, S. & Roberts, S., 2021, ‘Competition, productive capabilities and structural transformation in South Africa’, The European Journal of Development Research 33(2), 253–274. https://doi.org/10.1057/s41287-020-00349-x

Motebele, M.M., 2018, ‘Rethinking supply chain as a driver for efficient operations and strand of linked operations in South African steel production plants’, in Proceedings of the world congress on engineering, vol. 2, 4th–6th July, London.

Mráček, P. & Mucha, M., 2011, ‘Advergaming: Application of knowledge in the process of the competitive advantage improvement’, Trends Economics and Management 5(8), 139–147.

Mukhtar, U., 2015, ‘Supply chain competitiveness with the perspective of service performance between supply chain actors: A theoretical model’, in Joint international conference, 27th–29th May 2015, Bari.

Mukwakungu, S.C., Mabasa, M.D., Mankazana, S., Mzileni, X. & Burakeye, S.A., 2019, ‘The impact of just in time (JIT) in inventory management – Perspectives from two case studies in a South African environment’, in Proceedings of the international conference on industrial engineering and operations management, Bangkok, March 05–07, 2019, pp. 1271–1278.

Mumassabba, J, Muchibi, W.M.M., Mutua, S.M. & Musiega, D., 2015, ‘Factors influencing competitive advantage among supermarkets in Kenya: A case of Nakumatt Holdings Limited’, International Journal of Novel Research in Humanity and Social Sciences 2(3), 63–77.

Naqvi, M.H., Asim, D.M. & Manzoor, S., 2020, ‘Analysing the impact of supply chain agility on customer satisfaction through responsiveness and innovation’, CenRaPS Journal of Social Sciences 2(1), 26–40. https://doi.org/10.46291/cenraps.v2i1.8

Njeri, K.L. & Thuo, A., 2014, ‘Factors influencing sustainable competitive advantage among cut-flower firms’, International Journal of Current Business and Social Sciences (IJCBSS) 1(1), 1–17.

Nordin, N., MdDeros, B. & Abd Wahab, D., 2010, ‘A survey on lean manufacturing implementation in Malaysian automotive industry’, International Journal of Innovation, Management and Technology 1(4), 374–380.

O’Brien, R.M., 2017, ‘Dropping highly collinear variables from a model: why it typically is not a good idea’, Social Science Quarterly 98(1), 360–375.

Ocheri, C., Ajani, O.O., Daniel, A. & Agbo, N., 2017, ‘The steel industry: A stimulus to national development’, Journal of Powder Metallurgy & Mining 6(1), 1–6. https://doi.org/10.47672/ajscm.719

Ochieng, B., 2021, ‘Lean manufacturing practices and supply chain performance of sugar manufacturing firms in western Kenya’, American Journal of Supply Chain Management 6(1), 27–43.

Organisation for Economic Co-operation and Development (OECD), 2020, Steel market developments: Q4 2020, viewed 04 August 2021, from https://www.oecd.org/industry/ind/steel-market-developments-Q4-2020.pdf.

Pakdil, F. & Leonard, K.M., 2014, ‘Criteria for a lean organisation: Development of a lean assessment tool’, International Journal of Production Research 52(15), 4587–4607. https://doi.org/10.1080/00207543.2013.879614

Pal, A. & Kachhwaha, S.S., 2013, ‘Waste cooking oil: A promising feedstock for biodiesel production through power ultrasound and hydrodynamic cavitation’, Journal of Scientific Industrial Research 72, 387–392.

Panuwatwanich, K. & Nguyen, T.T., 2017, ‘The influence of organisational culture on total quality management implementation and firm performance improvement: Evidence from the Vietnamese construction industry’, Management and Production Engineering Review 8(1), 5–15. https://doi.org/10.1515/mper-2017-0001

Punnakitikashem, P., Buavaraporn, N. & Chen, L., 2013, ‘An investigation of factors affecting lean implementation success of Thai logistics companies’, in 24th POMS annual conference, Denver, USA, May 03-06, 2013, pp. 1–10.

Puvanasvaran, A.P., Huihui, Y. & Norazlin, N., 2014, ‘Managing waste elimination database in lean manufacturing: Improve problem-solving capability’, American Journal of Engineering and Applied Sciences 7(2), 271–281. https://doi.org/10.3844/ajeassp.2014.271.281

Rajagopal, A., 2010, ‘Impact of quality programs on supply chain performance’, Global Management Review 4(3), 1–14.

Republic of South Africa Department of Trade And Industry, 2019, National industry policy framework, Government Printer, Pretoria.

Rocha, D.V., 2017, ‘Lean manufacturing applied in a large company in the Brazilian steel industry’, Management Decision 38(1), 129–148.

Sadikoglu, E. & Olcay, H., 2014, ‘The effects of total quality management practices on performance and the reasons of and the barriers to TQM practices in Turkey’, Advances in Decision Sciences 5(1), 31–48. https://doi.org/10.1155/2014/537605

Sakuramoto, C., Di Serio, L.C. & Bittar, A.V., 2018, ‘Impact of supply chain on the competitiveness of the automotive industry’, RAUSP Management Journal 54(2), 205–225. https://doi.org/10.1108/RAUSP-07-2018-0051

Salimova, T., Vatolkina, N. & Makolov, V., 2014, ‘Strategic partnership: Potential for ensuring the sustainable university development’, Quality Innovation Prosperity/Kvalita Inovacia Prosperita 18(1), 07–124. https://doi.org/10.12776/qip.v18i1.320

Saunders, M., Lewis, P. & Thornhill, A., 2016, Research methods for business students, Pearson Education, Harlow.

Schoeman, Y., Oberholster, P. & Somerset, V., 2021, ‘A decision-support framework for industrial waste management in the iron and steel industry: A case study in Southern Africa’, Case Studies in Chemical and Environmental Engineering 3, 1–9. https://doi.org/10.1016/j.cscee.2021.100097

Segarra-Moliner, J.R., Moliner-Tena, M.A. & Sánchez-Garcia, J., 2013, ‘Relationship quality in business to business: A cross-cultural perspective from universities’, Marketing Intelligence & Planning 3(2), 14–26. https://doi.org/10.1108/02634501311324573

Shang, K.H., Zhou, S.X. & Van Houtum, G.J., 2010, ‘Improving supply chain performance: Real-time demand information and flexible deliveries’, Manufacturing & Service Operations Management 12(3), 430–448. https://doi.org/10.1287/msom.1090.0277

Sharma, V., Dixit, A.R. & Qadri, M.A., 2015, ‘Impact of lean practices on performance measures in context to Indian machine tool industry’, Journal of Manufacturing Technology Management 26(103), 1218–1242. https://doi.org/10.1108/JMTM-11-2014-0118

Simona, U. & Cristina, D., 2015, ‘Review on lean tools used in manufacturing process improvement (I)’, Ovidius University Annals, Series Economic Sciences 15(1), 642.

Siva, V., Gremyr, I., Bergquist, B., Garvare, R., Zobel, T. & Isaksson, R., 2016, ‘The support of quality management to sustainable development: A literature review’, Journal of Cleaner Production 138(Part 2), 148–157. https://doi.org/10.1016/j.jclepro.2016.01.020

Slack, N.J. & Singh, G., 2020, ‘The effect of service quality on customer satisfaction and loyalty and the mediating role of customer satisfaction: Supermarkets in Fiji’, The TQM Journal 32(3), 543–558. https://doi.org/10.1108/TQM-07-2019-0187

Soni, A., Chandrakers, R., Sinha, V.K., Patel, A.L. & Soni, G.K., 2013, ‘Application of lean manufacturing in steel manufacturing industries by managing total quality management’, International Journal of Mechanical and Production Engineering Research and Development 3(5), 79–86.

Sreedharan, R., Raju, V., Rajkanth, R. & Nagaraj, R.M., 2016, ‘An empirical assessment of Lean Six Sigma awareness in manufacturing industries: Construct development and validation’, Total Quality Management and Business Excellence 29(5–6), 686–703. https://doi.org/10.1080/14783363.2016.1230470

Statistics South Africa, 2018, Gross domestic product 4th quarter 2017, viewed 10 August 2019, from http://www.statssa.gov.za/publications/P0441/P04414thQuarter2018.pdf

Statistics South Africa, 2019, ‘Manufacturing: Production and sales (Preliminary) 2019’, viewed 23 July 2020, from http://www.statssa.gov.za/publications/P30412/P30412January2019.pdf.

Syed, S., Barlow, P. & Syed, S., 2018, Just-in-Time (JIT) advantages and disadvantages, viewed 23 June 2020, from https://babington.co.uk/blog/accounting/just-in-time-advantages-and-disadvantages/.

Talib, F., Asjad, M., Attri, R., Siddiquee, A.N. & Khan, Z.A., 2020, ‘A road map for the implementation of integrated JIT-lean practices in Indian manufacturing industries using the best-worst method approach’, Journal of Industrial and Production Engineering 37(6), 275–291. https://doi.org/10.1080/21681015.2020.1788656

Tang, Z., Chenand, X. & Luo, J., 2011, ‘Determining socio psychological drivers for rural household recycling behaviour in developing countries: A case study from Wuhan, Hunan, China’, Environment and Behaviour 43(6), 848–877. https://doi.org/10.1177/0013916510375681

Tarigan, Z.J.H. & Siagian, H., 2021, ‘The effects of strategic planning, purchasing strategy and strategic partnership on operational performance’, doctoral dissertation, Petra Christian University, Surabaya, Indonesia.

Trade and Industrial Policy Strategies (TIPS), 2020, COVID-19: The South African steel industry, viewed 24 July 2021, from https://www.tips.org.za/images/TIPS_Policy_Brief_COVID-19_The_South_African_steel_industry_April_2020.pdf.

Tran, N.P. & Vo, D.H., 2020, ‘Human capital efficiency and firm performance across sectors in an emerging market’, Cogent Business & Management 7(1), 1738832. https://doi.org/10.1080/23311975.2020.1738832

Trollip, H., McCall, B. & Bataille, C., 2022, ‘How green primary iron production in South Africa could help global decarbonisation’, Climate Policy 22(2), 236–247. https://doi.org/10.1080/14693062.2021.2024123

Van Der Merwe, K., 2014, ‘Development of a lean culture diagnostic tool, Department of Industrial Engineering’, presented at EPPM 2014 conference, Nelson Mandela Metropolitan University, Port Elizabeth, November 26–28, 2014.

Van Der Walt, A., 2012, ‘Implementing lean best practices in an automotive component parts manufacturing company’, BEng. dissertation, University of Pretoria, Pretoria.

Vanichchinchai, A., 2019, ‘The effect of lean manufacturing on a supply chain relationship and performance’, Sustainability 11(20), 5751. https://doi.org/10.3390/su11205751

Verma, A. & Seth, N., 2011, ‘A conceptual framework of supply chain competitiveness’, International Journal of Human and Social Sciences 6(1), 5–10. https://doi.org/10.1504/IJVCM.2011.043227

Viljoen, J.N., 2015, ‘The impact of implementing selected lean principles in a South African gold processing plant’, Master in Business Administration, North-West University, Potchefstroom.

Worldsteel, 2020, Worldsteel Short Range Outlook June 2020, viewed 24 May 2022, from PowerPoint Presentation (steelforum.org).

Wyk, G. & Naidoo, V., 2016, ‘Critical assessment of Just-in-Time (JIT) process within a South African company: The case of Sabertek’, Investment Management and Financial Innovation 13(2), 237–249. https://doi.org/10.21511/imfi.13(3-1).2016.10

Zairi, M., 2013, ‘The TQM legacy-gurus’ contributions and theoretical impact’, The TQM Journal 25(6), 659–676. https://doi.org/10.1108/TQM-06-2013-0069

Zalk, N., 2021, ‘Structural change in South Africa’, in Structural transformation in South Africa: The challenges of inclusive industrial development in a middle-income country, online edn., pp. 28–52, Oxford Academic, Oxford.

Appendix 1

TABLE 1-A1: Measurement instruments.