THE GETTY CENTER LIBRARY ' m < 5 ^ Digitized by the Internet Archive in 2018 with funding from Getty Research Institute https://archive.org/details/handworkinwood00noye_0 HANDWORK IN WOOD % WILLIAM NOYES, M.A. Assistant Professor. Department of Industrial Arts, Teaekers College, Columbia University NEW YORK CITY n 180 N'95 '915 The Manual Arts Press Peoria., Illinois 1915 COPYRIGHT WILLIAM NOYES 1910 SECOND EDITION. 1911 THIRD EDITION. 1912 FOURTH EDITION. 1913 FIFTH EDITION. 1914 SIXTH EDITION, 1915 THE GETTY CENTER Oo m? students past present and future a token of gratitude for and inspiration FOBEWOBD This book is intended primarily for teacheis of woodwork, hut the author hopes that there will also be other workers in wood, profes¬ sional and amateur, who will find in it matter of interest and profit. The successful completion of the book is due chiefly to the un¬ tiling assistance of my wife, Anna Gausmann Noyes, who has made almost all of the drawings, corrected the text, lead the proof, and attended to numberless details. Acknowledgments are hereby thankfully given for corrections and suggestions in the text made by the following persons: Mr. Chas. W. Weick of Teachers College, and Mr. W. F. Yionm of Public School No. 5, of New York City, for revision of Chapters JY and V on tools and fastenings. Mr. Clinton S. VanDeusen of Bradley Fo'ytechnie Institute, for revision of Chapter X on wood finishing. 'filie Foicst Service, Washington, D. C. for the originals of Figs. 1, 2, 3, 5, 7, 8, 9, 10, 11, 13, 17, 18, 21, 22, 23, 24, 2(1, 27, 28, 29, 31, 33, and 54. The New York State Forest Fish and Game Commission for the originals of Figs. 12, 11, 15, and 47. T. II. McAl ister of New York for the originals of Figs. 16 and 20. 'Fhe Detioit Publishing Company for the original of Fig. 6. The B. F. Stuitevant Company, Hyde Park, Mass., for the orig¬ inal of Fig. 57. Doubleday, Page & Co. for the original of Fig. 30. Mr. William II. Cochrane, Indianapolis, Ind., for the champing device shown in Fig. 255. Sargent & Company, New Haven, Conn., for electrotypes of Figs. 11)3, 194, 196, and 197; W. C. Teles & Company, Chicago, Ill., for electrotype of Fig. 168; The Berlin Machine Works, Beloit, Wis., for electrotype of Fig. 35; A. A. Loetscher, Dubuque, Iowa, for electro¬ type of Fig. 259; and the Stanley Pule and Level Co., New Biitain. Conn., for electrotype of Fig. 117. l Allis Chalmers Company, Milwaukee, Wis., Clark Brothers, Bel¬ mont, N. Y., The M. Garland Company, Bay City, Mich., The Pres¬ cott Company, Menominee, Mich., for illustrations of sawmilling machinery. And most of all, I wish to acknowledge my obligation to the nu¬ merous writers of whose books and articles I have made free use, to which references are made in the appropriate places. CONTEXTS. CHAPTER PAGE General Bibliography .. 4 I Logging. 7 II Sawmilling.30 III The Seasoning and Measuring of Wood .... 45 IV Wood Hand Tools.51 V Wood Fastenings.123 VI Equipment and Care of the Shoo.136 VII The Common Joints.151 VIII Types of Wooden Structures.183 IX Principles of Joinery.203 X Wood Finishing.209 Tndex 224 GENERAL BIBLIOGRAPHY Adams, Henry, Joints in Wood-Work. London: 00 Queen Victoria St. 1S94. Alexander, Jerome, The Grading and Use of Glue. Wood Craft, 5: 1G8, Sep. ’00. Bailey, Charles H., A Study of Manual Training Equipments. Manual Train¬ ing Magazine, 0:82. Jan. ’05. Barnard, Charles, Tools and Machines. N. Y.: Silver, Burdett and Co. 1903. Barter, S. M., Woodwork. London: Whittaker and Co. 1892. Benson, W. A. S., Elements of Handicraft and Design. London: Macmillar and Co. 1893. Brannt, W. T., Painter, Gilder and Varnisher. Philadelphia: H. C. Baird & Co. 1893. Bruncken, Ernest, North American Forests and Forestry N. 1'.: G. P. Put¬ nam’s Sons. 1S99. Clark, R. I., Varnish and Fossil Remains. London: Chas. Letts & Co. No date. Compton, A. G., First Lessons in Woodworking. N. Y.: Ivison, Blakeman. Taylor and Co. 1888. Crawshaw, Fred D., Problems in Furniture Making. Peoria, Ill.: The Man¬ ual Arts Press. 1906. Disston, Henry, and Sons, Handbook for Lumbermen. Philadelphia, Pal Dunlap, Frederick, Kiln-drying Hardwood Lumber. Wood Craft, 6: 133, Feb. ’07. Ellis, George, Modern Practical Joinery. London: B. T. Batsford, 480 pp., 1902, ’03, ’04 and ’07. Encyclopedia Britannica, Lac, Varnish. N. Y.: Scribner's. 1878. Foster, Edwin W., Elementary Woodworking. Boston: Ginn and Co. Goss, W. F. M., Bench Work in Wood. Boston: Ginn and Co. 1S87 and 190-5. Griffith, Ira S., Essentials of Woodworking. Teoria Ill.: Manual Arts Press. 1908. Hammacher, Schlemmer & Co., Tools. Catalog No. 355. N. Y. 1908. Hammacher, Schlemmer & Co., Cabinet Hardware. Catalog No. 151. N. Y. 1904. Hodgson, Fred T., The Up-to-date Hardwood Finisher. Chicago: Fred J. Drake and Co. 1904. Hodgson, Fred T. The Carpenter’s Steel Square and Its Uses. N. Y.: In¬ dustrial Publishing Co. 1S80. Hovey-King, Alvin, The Lumber Industry of the Pacific Coast. Review of Reviews. 27: 317, Mr., ’03. 4 GENERAL BIBLIOGRAPHY. 0 Hulbert, W. H., The Lumber Jack and His Job. Outlook, 76: 801, Ap. 2, ’04. International Correspondence School, The Building Trades Pocketbook. Scranton, Pa. International Textbook Co. 2nd edition. 1905. International Encyclopedia, Lac-Insect, Varnish. N. Y.: Dodd, Mead and Co. 1902-1904. Jones, J. E., Lumbering in the Northwest. Cosmopolitan, 15: 63, May 1893. Larsson. Gustaf, Elementary Sloyd and Whittling. N. Y.: Silver, Burdett & Co. 1906. Maire, F., The Modern Wood Finisher. Chicago: Press of the Western Painter. Munn, M. J., Great Industries of the V. S. — Lumber. Cosmopolitan, 37: 441, Aug. ’04. Murray, M. W., Problems in Wood-working. Peoria, Ill.: Manual Arts Press. 1905. Murray, M. W., The Manual Training Room and Its Equipment. Year Book of the Council of Supervisors for 1906. pp. 69-86. Park. Joseph C. Educational Woodworking for School and Home. The Macmillan Co., 1908. Pinchot, Gifford, A Primer of Forestry. Parts I and II, U. S. Dept, of Agric. For. Serv. Bull. No. 24. 1899 and 1905. Purfield, H. T., The Length of Nails. Wood Craft, 5: 181, Sp. ’06. Rivingston, see South Kensington Council on Education. Rouillion, Louis. Economics of Manual Training. N. Y.: The Derry Col- lard Company. 1905. Roth, Filibert, A First Book of Forestry. Boston: Ginn & Co. 1902. Sargent & Co., Standard Steel Squares. New Haven, Conn. Seaton, Geo. A., A Clamp for Use at the Grindstone. Woodcraft, 6: 96. Jan., ’07. Selden, F. H., Elementary Woodwork. N. Y.: Rand, McNally & Co. 1906. Siekels, Ivin, Exercises in Woodworking. N. Y.: D. Appleton & Co. 1889. Smith, K., Lumbering by Machinery. World’s Work, 7: 4435, Feb. ’04. Smith, R. H., Cutting Tools. London: Cassell & Co. 1884. South Kensington Council on Education, Notes on Building Construction. 3 vols. London: Rivington. 1883-1889. Standage, H. C., Glues and Cements for the Use of Woodworkers. Wood Craft, 7: 48, May, ’07. Tate, James M., Training in Wood Work. Minneapolis: North Western School Supply Co. About 1905. Trout, W. H., The Modern Sato Mill. Cassier’s Magazine, 11: 83-95, 184-195, Dee. ’96 and Jan. ’97. U. S. Department of Agriculture Forest Service Classified List of Publications. Forest Service Bulletins: No. 10. Filibert, Roth, Timber. 1895. No. 34. Wm. F. Fox, A History of the Lumber Industry in the State of New York, 1902. No. 41. Hermann von Schrenk, Seasoning of Timber. 1903. 6 HANDWORK IN WOOD. Van Deusen, Clinton S., Methods of Wood Finishing. Manual Training Mag¬ azine, 6: 93. Jan. ’05. Van Deusen, Clinton S., Logging in the South. Manual Training Magazine , 1: 93. Jan. ’00. Wells, Percy A., and Hooper, John, Modern Cabinet Work, New York, John Lane, 1909. Wheeler, C. G., Woodworking for Beginners. N. Y.: G. P. Putnam’s Sons. 1899. White, Stewart Edward, The Blazed Trail. N. Y.: McClure, Phillips & Co. 1904. White, Stewart Edward, From Forest to Saw Mill. Junior Munsey, 10: 302, Je. ’01. Anonymous. Nails. Wood Craft. 5: 103. Jl. ’06. A Dry-Kiln of Progressive Style. Wood Craft, 6: 31, Nov. ’06. Lumbering in Louisiana. Wood Craft, 4: 55, Nov. ’05. The Lac Industry of Assam, Journal of the Society of Arts. 49: 192. Feb. 8 , ’ 01 . Chapter I. LOGGING. *The rough and ready methods common in American logging op¬ erations are the result partly of a tradition of inexhaustible supply, partly of the fear of fire and the avoidance of taxes, partly of an eagerness to get rich quick. Most of the logging has been done on privately owned land or on shamelessly stolen public land, and the lumberman had no further interest in the forest than to lumber it expeditiously. Preliminary to the actual logging are certain necessary steps. First of all is landlooking. This includes the survey of the forest Fig - . 1. Making- a Valuation Survey land for the purpose of locating good timber. Fig. 1. Most of the woodland has previously been roughly surveyed by the government and maps made indicating which parts are private land and which are still held by the government. The boundaries of townships, sec¬ tions, quarter sections, eighties, forties, etc., are indicated by “blazes” *See the author’s Wood and Forest, pp. 251-270 for a discussion of the causes of destructive lumbering in America. 7 8 HANDWORK IN WOOD. on trees, Fig. 2, so that the “cruiser” or “looker” as he goes thru I tie woods can identify them with those on his oil paper map. The cruiser also studies the kinds and char¬ acter of the trees, the contour of the ground, tire proximity to streams,-—all with the view to marketing the product. Acting on the information thus gained by the cruiser, the lumberman purchases his sections at the proper land office, or if he is less scrupulous, buys only enough to serve as a basis for operations. Enormous fortunes have been made by timber thieves, now respectable mem¬ bers of the community. As a fur¬ ther preliminary step to lum¬ bering itself, the iote road and camp are built. The tote road is a rough road on which sup¬ plies for crew and cattle can be taken to camp from civilization. It is barely passable for a team and a wagon, but it serves its purpose, and over it come more men and horses, lumber for the floors and roofs of the shan¬ ties and for the rude pieces of furniture that will be needed, tarred paper to make the roofs tight, a few glazed window sashes, a huge range and a number of box stoves, dishes and kitchen utensils, a little stock of goods for the van, blankets by the dozen and score, and countless boxes and bar¬ rels and bags of provisions. 1 The camp itself, Fig. 3, is built of logs, roofed with plank, cov¬ ered with heavy tar paper, and dimly lighted. There are usually five buildings,—the men's camp, the cook camp, the office, the barn, and the blacksmith's shop. Many camps accommodate from eighty to one hundred men. The men’s camp is filled with bunks and is heated by a stove and in general roughly furnished. Cooking and eating are done in the cook camp, where the cook and his assistant, the “eookee,” sleep. The office is occupied by the foreman, log-seal- ^ulbert: The Lumber Jack; Outlook, 76: 801, April 2, ’04. LOGGING. 9 ers and clerks. Here the books and accounts are kept, and here is the “van,” stocked with such goods as will supply the immediate needs of the lumber jacks. Fig 1 . 3. Winter I^ogging - Camp, itasca County, Minnesota Before winter sets in the main road is built, Fig. 15, p. 17, very carefully graded from the camp down to the nearest mill or railway siding, or oftener to the stream down which the logs are to be floated. This road has to be as wide as a city street, 25 feet. The route is carefully chosen, and the grade is made as easy as possible. Much labor is spent upon it, clearing away stumps and rocks, leveling up with corduroy, building bridges strong enough to carry enormous loads, and otherwise making it as passable as can be; for when needed later, its good condition is of first importance. This main road is quite distinct from and much superior to the tote road. At intervals alongside the main road, small squares called skid- ways are cleared of brush and in each of them two tree trunks, “skids,” are laid at right angles to the road. On these the logs, when cut later, are to be piled. Back from the skidways into the woods the swampers cut rough, narrow roads called dray roads or travoy roads,—mere trails sufficiently cleared of brush to allow a team .of horses to pull a log thru. All these are operations preliminary to the felling of trees. The tools commonly used in logging are shown in Fig. 4. When every¬ thing is ready for felling, the “fitter” goes ahead marking each tree to be felled and the direction in which it is to fall by cutting a notch on that side. Then come the saw} r ers in pairs. Fig. 5. First 10 HANDWORK IN WOOD. they chop a deep gash on the side of the tree toward which it is to fall, and then from the opposite side begin cutting with a long, Tuttle-tooth, crosscut-saw. The saw is a long, flexib'e ribbon of steel, with handles so affixed to each end that they can be removed easily. The cut is made on the pulling stroke, and hence the kerf can be very narrow. As soon as the saw is well within the trunk, the sawyers drive iron wedges info the kerf behind it, partly to keep the weight of the trunk from binding the saw, and partly to direct its fall. Then the saw is pulled back and forth, and the wedges LOGGING. 11 driven in farther and farther, until every stroke of the maul that drives them sends a shiver thru the whole tree. Just as the tree is ready to go over, the saw han¬ dle at one end is unhooked and the saw pulled out at the other side. “Timber !,” the men cry out as a warning to any working near by, for the tree has begun to lean slightly. Then with a hastening rush the top whistles thru the air, and tears thru the branches of other trees, and the trunk with a tremendous crash strikes the ground. Even hard¬ ened loggers can hardly keep from shouting, so impressive is the sight of a falling giant tree. All this seems simple enough in outline, but the actual execu- tion requires considerable skill. Adirondack Mountains, New York. Trees seldom stand quite vertical, there is danger of lodging in some other tree in thick woods, and it is therefore necessary to throw trees quite exactly. Some men become so expert at this that they can plant a stake and drive it into the Fig 1 . 6. Sawing - Logs into Lengihs. HANDWORK IN WOOD. 12 ground by the falling trunk as truly as if they hit it with a maul. On the other hand, serious accidents often happen in falling trees. Most of them come from “side winders,” i. e., the falling of smaller trees struck by the felled trees. After “faking” a tree, the sawyers mark off and saw the trunk into log lengths, Fig. G, paying due attention to the necessity of avoiding knots, forks, and rotten places, so that some of the logs are eighteen feet, some sixteen feet, some four¬ teen feet, and some only twelve feet in length. Meanwhile the swampers trim off the branches, Fig. 7, a job requiring no little skill, in order that the trunk may be shaved close but not gashed. Fig - . 7. Trimming - off Branches of Spruce. Adirondack Mountains. New York. Fig - . 8. Hauling- Spruce Logfs to the Skidway. Adirondack Mountains, New York. LOGGING. 13 This finishes the second group of operations, the felling. Next the logs are dragged out to the dray roads, Fig. 8. A heavy pair of tongs, like ice-tongs, is attached to one end, and the log is snaked out by horses to the skidway. If the log is very heavy, one end is put on a dray. By one way or another the log is dragged out and across the two parallel skids, on which it is rolled by cant-hooks to the end of skids toward the road way. If other logs already occupy the skids, each- new log as it arrives is piled on the first tier. As the pile grows higher, each log is “decked,” that is, rolled up parallel poles laid slanting up the face of the pile, by means of a chain passed under and over the log and back over the pile, Fig. 11. A horse hitched to the end of the chain hauls up the log, which is guided by the “send-up men” with their cant-hooks. Once piled, the logs are "scaled that is measured in order to compute the number of board feet in them, Fig, 9. The scaler gen¬ erally has an assistant, for logs in large piles must be measured a t both ends in order to deter¬ mine which is the upper end, the body of the log being out of sight. When measured each end of the log is stamped with a hammer with the owner’s mark, by which it can afterward be identified. Here the logs rest and the felling and skidding continue until deep snow falls and then the sleigh haul begins. For this the main road is especially prepared. First the road is carefully plowed with an immense V plow, weighted down by logs. To the plow are attached fans. Only an inch or two of snow is left on the ground by this plow, which is followed by another special plow to gouge the ruts, and by a gang of “road monkeys” who clear Fig. 9. “Scaling” Logs on the Skids. 14 HANDWORK IN WOOD. the road thoroly. Then follows an immense tank set on runners and holding perhaps seventy-five barrels of water, and so arranged as to flood the road from holes in the bottom of the tank, a sort of rough Fig-. 10. Making an ice Road by Flooding. road sprinkler, Fig. 10. This sprinkler goes over the road again and again until the road is covered by a clear, solid sheet of ice often Fig. 11. Decking Dogs on Skidway. LOGGXN G. 15 two feet thick, extending from the skidways to the banking grounds. This ice road is one of the modern improvements in logging. Once finished, these roads are beautiful pieces of construction with deep, clear ruts. They have to be constantly watched and repaired and this is the work of the “road monkeys.” If possible the road Fig-. 12. Loading a Sled from a Skidway. lias been made entirely with down grades but some of these are so steep that a man must be prepared with sand or hay to check too headlong a descent. When all is ready the sleigh haul begins. Piling on the sleighs or bobs, Fig. 12, is similar to piling on the skidways, but more diffi¬ cult, for the load has to be carefully balanced, Fig. 13. Chains bind the loads but the piling is only too apt to be defective, and the whole load “squash out” with a rush. It is a time of feverish activity. The sprinklers are at work till after midnight, the loaders are out long before daylight. The blacksmith is busy with re¬ pairs, the road monkeys work Flathead County, Montana. 16 HANDWORK IN WOOD. overtime, and the cook works all the time. “Everybody works.” The haul itself is full of excitement. The ponderous load of logs, weigh¬ ing anywhere from eight to thirty-five tons has to be conducted largely by its own momentum down this glassy road. If a horse fall noth¬ ing can save its life. If the runners get out of the ruts, the whole load, driver and all, is likely to be upset. It is an extremely hazard¬ ous job, Fig. 15. As each load comes down to the hanking grounds. Fig. 14, or log dump, it is stopped opposite long parallel skids. The wrapping chains are unhooked and the lower log on the skid side is worked out with cant- hooks till the whole load flat¬ tens out. The logs are then “decked” o n immense piles, sometimes a mile long and filling the whole river from bank to bank. A decking chain 300 feet long is sometimes required to roll the logs to their proper places. Here the logs rest till the spring freshets come. This completes the transportation by land. With the coming of the spring thaw, the river bed is filled with a freshet of water which seizes and carries the logs down stream. They often start on their water journey with a great crash. Many on the banks, however, have to be started on their way, and this is called “breaking out the roll ways.” Now comes the drive, an arduous and often perilous task. Some of the men are stationed along the shores to prevent the logs from lodging or floating into bays or setbacks. Some stand at the heads of bars or islands, where with pike poles they shove off the logs that might stop there and form a jam; others follow “sacking the rear” to clean out such logs as may have become stranded. This “sacking the rear” takes most of the time, Fig. 16. While “on the drive” men often work fourteen hours a day, a good part of the time up to their waists in ice water. Their boots are shod with “caulks,” or LOGGING. 17 Fig - . 15. The Sleigh Haul. Fig. 16. Sacking the Rear. 18 HANDWORK IN WOOD. spikes, to keep them from slipping on the logs, and they carry cither pike poles or peaveys, Fig. 17. The latter are similar to cant-hooks, except that they have sharp pikes at their ends. So armed, they have to “ride any kind of a log in any water, to pro¬ pel a log by jumping on it, by rolling it squirrel fash¬ ion with the feet, hv punt¬ ing it as one would a ca¬ noe ; to be skilful in pushing, prying, and poling other logs from the quarter deck of the same cranky craft.” Altho the logs are carried by the river, they have to be “driven” with amazing skill and bravery. The climax of hardship and courage is reached when a “/am” is formed, Fig. 18. Sometimes one or two logs are caught in such a way as to be locked or jammed and then soon other logs begin to accumulate behind them, till the whole river is full of a seemingly inextricable mass. Sometimes these jams can be loosened by being pulled apart, one log at a time. A hundred men can pull out an amazing number of logs in a day. The problem always is to set free or cut out certain “key”' logs, which lock the whole mass. Following is a description by Stewart Edward White of the breaking of sucli a jam: The crew were working desperately. Down on the heap somewhere, two logs were crossed in such a manner as to lock the whole. They sought those logs. Thirty feet above the bed of the river six men clamped their peaveys into the soft pine; jerking, pulling, lifting, sliding the great logs from their places. Thirty feet below, under the threatening face, six other men coolly picked out and set adrift one by one, the timbers not inextricably imbedded. From time to time the mass creaked, settled, perhaps even LOGGING. 19 moved a foot or two; but always the practised rivermen, after a glance, bent more eagerly to their work. * * * Suddenly the six men below the jam scattered. * * * holding their peaveys across their bodies, they jumped lightly from one floating log to another in the zig-zag to shore. * * * In the meantime a barely perceptible motion was communicating itself from one particle to another thru the center of the jam. * * * The crew redoubled its exertion, clamping its peaveys here and there, apparently at random, but in reality with the most definite of purposes. A sharp crack exploded immediately underneath. There could no longer exist any doubt as to the motion, altho it was as yet sluggish, glacial. Then in silence a log shifted—in silence and slowly—but with irresistible force * * * other logs in all directions up-ended. * * * Then all at once down by the face something crashed, the entire stream became alive. It hissed and roared, it shrieked, groaned, and grumbled. At first slowly, then more rapidly, the very fore-front of the center melted in¬ ward and forward and downward, until it caught the fierce rush of the freshet and shot out from under the jam. Far up-stream, bristling and formidable, the tons of logs, grinding savagely together, swept forward. * * * Then in a manner wonderful to behold, thru the smother of foam and spray, thru the crash and yell of timbers, protesting the flood’s hurrying, thru the leap of destruction, the drivers zigzagged calmly and surely to the shore. Sometimes cables have to be stretched across the chasm, and spe¬ cial rigging devised to let the men down to their dangerous task and more especially to save them from danger when the crash comes. 20 HANDWORK IN WOOD. Fig. 21. Logs in Boom. Glens Falls, New York. LOGGING. 21 In case such efforts are unavailing, it is necessary to “shoot” the jam with dynamite. Another device resorted to where the supply of water is insufficient is the splash-dam, Fig. 20. The object is to make the operator independent of freshets, by accumulating a head of water and then, by lifting the gates, creating an artificial freshet, sufficient to float the timber down stream. Fig. 22. A Sorting Jack. Thus by one means and another, the logs are driven along until caught by a boom, Fig. 21, which consists of a chain of logs stretched across the river, usually at a mill. Since the river is a common carrier, the drives of a number of logging companies may float into the mill pond together. But each log is stamped on both ends, so that it can be sorted out, Fig. 22, and sent into the boom of its owner. MECHANICAL METHODS IN LUMBERING. The operations described above are those common in the lumber regions of the northeast and the Lake States. But special conditions produce special methods. A very effective device where streams are small is the flume, Fig. 23. This is a long wooden trough thru which water is led, and the logs floated end on. It is sometimes many miles long; in one case in California twenty-five miles. HANDWORK IN WOOD. 90 In the South where there is no snow, logs are largely brought out to the railway or river by being hung under immense two-wheeled trucks, called s 1 ip-tongue carts, drawn by mules, Fig. 24. The wheels are nearly eight feet in diameter. Fig-. 23. Six Mile Flume. Adirondack Mountains, New York. Some kinds of wood are so heavy that they will not float at all, and some sink so readily that it does not pay to transport them by river. In such cases temporary railways are usually resorted to. On the Pacific coast, where the forests are dense, the trees of enor¬ mous size, and no ice road is possible, still other special methods have been devised. On so great a scale are the operations conducted that they may properly be called engineering feats. Consider for a mo¬ ment the size of the trees; red fir ranges from five to fifteen feet in diameter, is commonly two hundred fifty feet high, and sometimes Hirer hundred twenty-five feet high. The logs are commonly cut twenty-four feet long, and such logs often weigh thirty to forty tons Fig. 24. Hauling Logs by Mules. Ocilla. Georgia. LOGGING. 23 Fig'. 25. A Twenty-Five Foot Saw used for Crosscutting Big Logs. each, and the logs of a single tree may weigh together one hundred fifty tons. The logging of such trees requires special appliances. Until recently all the improved methods were in forms of transpor¬ tation, the felling still being done by hand with very long saws, Fig. 25 , but now even the felling and sawing of logs in the forest is partly done by machinery. Fig. 26. Hauling Big Logs by Donkey Kngir.c. 24 HANDWORK IN WOOD. To work the saw, power is supplied by a steam or gasoline engine mounted upon a truck which can be taken readily from place to place. As the maximum power required is not over ten-liorse-power, the apparatus is so light that it can be moved about easily. The saw can be adjusted to cut horizontally, vertically, or obliquely, and hence is used for sawing into lengths as well as for felling. Falling beds. Since the weight of a two hundred fifty foot fir is such that if the impact of its fall be not gradually checked the force with which it strikes the ground may split the trunk, a bed for its fall is prepared by the swampers. Usually piles of brush are placed as buffers along the “falling line” so that the trunk will strike these. If the tree stands on the hill side, it is thrown up hill, in order to shorten the fall. After the felling comes the trimming of branches and knots and “rossing” of bark, to lessen the friction in sliding along the skidway. The slcidway. By the skidway in the Puget Sound region is meant a corduroy road. This is constructed of trunks of trees rang¬ ing from a foot to two feet in diameter. These are “rossed,” that is, stripped of their bark and laid across the road, where they are held in place by pegs driven into the ground, and by strips spiked upon the tops of the logs. If possible they are laid in swampy places to keep the surface damp and slippery. At turns in the road, pulleys are hung, thru which the hauling cables pass. The skidway runs to the railway siding or water’s edge. Over these skidways the logs are hauled out by various means. Formerly “strings” of oxen or Perch- eron horses were used, but they are now largely superseded by some form of donkey engine, Figs. 26 and 29. These are placed at the center of a “yard.” Yarding is the skidding of logs to the railway or water way by means of these donkey engines. Attached to the donkey engine are two drums, one for the direct cable, three-fourths to one inch in di¬ ameter and often half a mile long, to haul in the logs, the other for the smaller return cable, twice as long as the direct cab’e and used to haul back the direct cable. At the upper end of the skidway, when the logs are ready to be taken to the railway or boomed, they are fastened together, end to end, in “turns” of four or more. The direct cable is attached to the front of the “turn”, and the return cable to the rear end. By winding the direct cable on its drum, the “turn” is hauled in. The return catde is used to haul back the end LOGGING. 25 of the direct cable, and also, in case of a jam, to pull back and straighten out the turn. Instead of a return cable a horse is often used to haul out the direct cable. Signaling from the upper end of the skidway to the engineer is done by a wire connected to the don¬ key’s whistle, by an electric bell, or by telephone. Sometimes these donkey engines are in relays, one engine hauling a turn of logs to within reach of the next one, which passes it on to the next until the siding is reached. Fig-. 27. Seif Propellirig Log Loader. Courtesy of Clyde Iron Works, Duluth, Minn. Where there are steep canons to be crossed, a wire trolley may be stretched and the great logs carried over suspended from it. In the South a complicated machine called a steam skidder, equipped with drums, booms, etc., is much used both for skidding in the logs and then for loading them on the cars. It is itself mounted on a flat car. An improvement on this is the self-propelling log loader, Fig. 27, which is widely used both on the Pacific coast and of late in the Lake Superior region. It is a combined locomotive, skidder and loader. Its most unique feature is that the truck and wheels can be raised off the railway track so as to allow flat cars to rim underneath. This feat is accomplished thus: As the truck rises, the weight of the machine is taken upon steel legs, at the lower curved ends of which are shoes which rest on the railroal ties outside of the tracks. The IIANDWOIiK IN WOOD. truck of the loader is then folded up under it out of the way and cars can run under it, the curved legs giving plenty of clearance. The derrick attached is of the breast type, the two legs being firmly fastened. When anchored the engine can be used either for skidding Fig-. 28. Log- Train. Humboldt County, California. or loading. For skidding, there are two cables, one being run out while the other is being wound on its drum. In loading, the machine is located so that the empty car will be directly in front of it, and then the logs are lifted up and placed on the car by the derrick. When the car is loaded, the machine can pull the next car under itself into place. With the help of four men it can load from 125,000 to 150,000 feet of timber in a day. By means of the cable it can make up a train, and then by lowering the truck until the wheels carry the weight, it is converted into a loco¬ motive and hauls the train away to the mill or railway station at the rate of three or four miles at hour. As forests are cut away along the water courses, railways have to be resorted to more and more, Fig. 28. This has had a stimulative effect on the logging business, for now the logger is independent of the snow. On account of the steep grades and sharp curves often neces¬ sary in logging railways, a geared locomotive is sometimes used. It can haul a train of twenty loaded cars up a twelve per cent grade. The geared engine has also been used as a substitute for cable power, in “yarding” operations. The “turns” of logs are drawn LOGGING. 27 Fig-. 29. Donkey Engine Yarding. Fig. 3U. Giant Raft. In the background is a completed raft; in the foreground a cradle in which a raft is being built. 28 HANDWORK IN WOOD. over the ground between the rails, being fastened to the rear of the engine by hook and cable. This has proved to be a very economical use of power and plant. Another method of traction where the woodland is open enough is vdth a traction engine. The ones employed have sixty to one hundred horse power. The great logs may be placed on wood rollers, as a house is when moved, or the logs may be hauled in on a low truck with broad wheels. The “tractor” hauls the log direct to the railway if the distance is not too great. Fig. 31. Snow locomotive. Takes the place of 12 teamsters and 12 horses. Minnesota. In Northern Michigan a “snow locomotive,” Fig. 31, is coming into use, which has tremendous tractive power, hauling one hundred to one hundred fifty tons of lumber over snow or ice. It moves on runners, but there is between them a large cylinder armed with teeth. This cylinder can be raised or lowered by the operator as it moves over the surface of the ground. The teeth catch in the snow or ice, and since the cylinder is heated by the exhaust steam, it melts and packs the snow for the trucks following it. The drum is six feet in diameter, with walls an inch and a half thick, and it weighs seven tons. It is used in all sorts of places where horses cannot go, as in swamps, and by substituting wheels for runners it has even been used on sand. In the Canadian lakes there has been devised a queer creature called an “alligator,” a small and heavily equipped vessel for hauling the logs thru the lakes. When its operations in one lake are finished, a wire cable is taken ashore and made fast to some tree or other safe anchorage, the capstan on its forward deck is revolved by steam and the “alligator” hauls itself out of the water across lots to the next lake and begins work there. LOGGING. 29 The greatest improvement in water transportation is the giant raft, Fig. 30. When such a raft is made up, logs of uniform length are placed together, the width of the raft being from sixty to one hundred feet and its length, one thousand feet or more. It may con¬ tain a million board feet of timber. The different sections are placed end to end, and long boom sticks, i. e., logs sixty to seventy feet long, are placed around them to bind the different sections together, and finally the whole mass is heavily chained. Such a raft has been towed across the Pacific. LOGGING. References*: River Lumbering. Pinchot, Primer, II, pp. 40-53. White, Blazed Trail, pp. 5-15, 25, 38-39, 52-53, 63-05, 72- 85, 91-99, 113-125, 134, 181- 19G, 216-229, 257, 268, 320- 343, 355, 365 ff. For. Bull., No. 34, pp. 33-41, Fox. White, Jun. Mun. 10: 362. Hulbert, Outl., 76; 801. Wood Craft, 4: 55. Smith, K., World’s Work, 7: 4435. Mechanical Methods. World’s Work, 7: 4435. Outl. 76: 812. Bruncken, p. 86. Bruncken, pp. 76-87. Munn, Cosmop., 37: 441. Roth, First Book, pp. 133-174. Hovey-King, Rev. of Rev., 27: 317, Jones, Cosmop. 15: 63. Price, World’s Work, 5: 3207. For. Bull. No. 61. Cassier, 29: 443, April, ’06. Cosmop., 37: 445. Rev. of Rev. 28: 319. For general bibliography see page 4. Chapter II. SAWMILLING. The principal saws in a mill are of three kinds, the circular, Fig. 32, the gang, Fig. 33, and the band, Fig. 34. The circular-saw, tlio very rapid, is the most wasteful because of the wide kerf, and of course the larger the saw the thicker it is and the wider the kerf. The waste in sawdust is about one-fifth of the log. In order to lessen this amount two smaller saws, one hung directly above the other, have been used. One saws the lower half of the log and the other the upper half. In this way, it is possible to cut very large logs with the circular-saw and with less waste. The circular-saw is not a per¬ fectly flat disc, but when at rest is slightly convex on one side and concave on the other. This fullness can be pushed back and forth as can the bottom of an oil-can. When moving at a high rate of speed, however, the saw flattens itself by centrifugal force. This enables it to cut straight with great accuracy. A gang-saw is simply a series of straight saw-blades set in a ver¬ tical frame. This has a reciprocating motion, enabling it to cut a log into a number of boards at one time. It has this drawback, that it must cut the size of lumber for which it is set; that is, the sawyer has no choice in cutting the thickness, but it is very economical, wast¬ ing only one-eighth of the log in sawdust. A special form is the floor¬ ing gang. It consists of a number of saws placed one inch apart. Thick planks are run thru it to saw up flooring. Fig-. 33. Double Circular-Saw and Carriage. 30 SAWMILLING. 31 The band-saw is fast displacing the other two, wherever it car be used. It cuts with great rapidity and the kerf is narrow. When first used it could not be depended upon to cut straight, hut by util¬ izing the same principle that is used in the circular-saw, of putting the cut¬ ting edge un¬ der great ten¬ sion by making it slightly shorter than the middle of the saw, it now cuts with great accuracy. Band¬ saws are now made up to 12 inches wide, 50 feet long, and run at the rate of 10,000 feet a minute. They are even made with the cutting teeth on both edges, so that the log can be sawed both going and coming. This idea was unsuccessful until the invention of the telescopic band-mill, Fig. 35. In this the entire mechanism carry- Fig. 34. Band-Saw. 32 HANDWORK IN WOOD. Fig. 35. Uouble-Cutting Telescopic Band- Mill. Mill in raised position tor large log. up out of the water on to a “jact chain, provided with saddles or s ing the wheels on which the band-saw revolves can be moved up and down, so as to bring the point where the saw leaves the upper wheel as close to the top of the different sized logs as possible. The usual modern mill is a two story building, Fig. 37, built at a convenient locality both for receiving the logs and for ship¬ ping the lumber. Whether the logs arrive by water or by rail, they are, if possible, stored in a mill-pond until used in order to prevent checking, discolora¬ tion, decay, and worm attack. From the pond they are hauled -ladder,” by means of an endless purs which engage the logs and Fig. 36. Jack-Ladder, with Endless Chain. SAWMILLING, 33 Fig 1 . 37. Two-Story Mill at Virginia, Minnesota, Showing Jack-Ladders and Consumer. 34 HANDWORK IN WOOD. draw them up into the second story on to the log slip, Fig. 36. After the logs have entered the mill, they are inspected for stones lodged in the bark, and for spikes left by the river men, and then measured. Under the log- slip is the steam “flipper” or “kicker,” Fig. 38, by means of which the scaler or his as¬ sistant, throwing a lever, causes the log to be kicked over to one side or the other, on to the log- deck, an inclined floor sloping toward the saw-carriage. Down this the log rolls until stopped by a log-stop, or log-loader, Fig. 39, a double-armed projection, which prevents it from rolling on the carriage till wanted. This stop is also worked by steam. By letting the steam into the cylinder which controls it, one log is rolled over on the carriage and the next one held. The log on the carriage is at once “dogged,” that is, clamped tight by iron dogs, the carriage is set for the proper cut, and moves forward to the saw which cuts off the first slab. The carriage is then “gigged" or reversed. This operation off¬ sets the carriage one-eighth of an inch so that the log returns entirely clear of the saw. In the same way two or three 1” boards are taken off, the dogs are then knocked out, and the log canted over half a revolu¬ tion. This is done by means of the “steam nigger,” Fig. 40, a long, perpendicular toothed bar which comes up thru the floor, engages the log, and turns it over till the sawn side comes up against the knees of the car- Fig-. 30. Log-Stop and Loader. By letting steam into the cylinder, the projecting arm revolves, rolling one log over onto the car¬ riage and holding the next one till wanted. Fig. 38. Log-Flipper. SAWMILLING. 35 riage. The log is dogged again and a second slab and several boards are taken off. The log or “stock” as it is now called, is 10", 13", 14", or 16" thick; the “nigger” then gives it a quarter-turn, leav¬ ing it lying on a sawn side. It is dogged again, and all sawn up except enough to make a few boards. 'This last piece is given a half¬ turn, bringing the sawn side against the knees, and it is sawn up. Another 1 o g comes on the carriage and the process is repeated. The saw-car- 43, riasre. Fig. i s propelled forward and back by a pis¬ ton running in a long cylinder, into either end of which steam can be turned by the operator. As the sawn boards fall off the log, they land on “live,” that is, revolv¬ ing rollers, which carry them along at the rate of 300 to 350 feet a Fig". 40. T he Steam Nigger. The toothed bar turns the log over into the desired position. minute. Stops are provided farther along to stop the boards wherever wanted, as at the edger, Fig. 43, or the slasher. From the live rollers the boards are transferred automatically, Fig. 44, by chains running at right angles to the rollers and brought within reach of the edger man. 36 HANDWORK IN WOOD. About one-third of the boards of a log have rough edges, 1 are called ” These must and “waney go thru the edger to make their edges parallel. The edger man works with great speed. He sees at once what can be made out of a board, places it in position and runs it thru. From the edger the boards are carried to the trimmer, which cuts the length. The lumberman’s rule is t, 'Tut so that you can cut again.” The so- called 16' logs are really 16' 6”. The trimmer, Fig. 45, now trims these boards to 16' 1," so that if desired they can still be cut again. The trimmer may be set to cut at any desired Fig-. 41. Steam Cant-Flipper. This machine is used to move cants, timber or lumber from live rollers to g-ang-s, band resaw mills, or else¬ where. The timber is dis¬ charged upon skid rollers, as shown, or upon transfer chains. length according to the specifications. The boards are now graded as to quality into No. 1, No. 2, etc., Fig. 46, and run out of the mill, to be stacked up in piles, Fig. 47. lio- timbers, or “cants” 2 are transferred from Fig. 42. Log-Carriage, holding quartered log in position to saw. the live rollers by means of the cant flipper, Fig. 41, to the gang- mill. Fig. 33, or may go directly from the saw on the live rollers to the back end of the mill where the first end is trimmed by a butting-saw or cut-off saw which swings, Fig. 4S. The timber is then shoved along on dead rolls and the last end trimmed by the 2 A “cant” is a squared or partly squared log. SAWMILLING. 37 Fig. 43. Double Gang Edger. This machine trims off the rough edges of the “waney” boards by means of the four saws in the main frame of the machine. Fig. 44. Automatic Steam Transfer for Timber, Lumber and Slabs. The boards are carried along by the cylinders, C C C, until they hit the bumper, B. This movement admits steam to the cylinder, CY, which raises the revolving chains or skids, which transfers the stock sidewise to other live rollers as required. 38 HANDWOKK IN WOOD. Fig 1 . 45. Automatic Gang Dumber-Trimmer. It may be set to cut automatically to any desired length. SAWMILLING. 39 Fig-. 48. Cut-off-Saw. This saw trims the ends of timbers. butting-saw to a definite length as specified, and shoved out. One of the most remarkable features of the modern mill is its speed. From the time the log appears till the last piece of it goes racing out of the mill, hardly more than a minute may have elapsed. A large part of the problem of sawmilling is the disposal of the waste. The first of these is the sawdust. In all first class mills, this together with shavings (if a planing-mill is combined) is burned for fuel. It is sucked up from the ma¬ chines and carried in large tubes to the boiler-room and there is mechanically supplied to the fires. The slabs, once considered as waste, contain much material that is now utilized. From the live rolls, on which all the material falls from the main band-saw, the slabs are carried off by transfer chains, and by another set of five rollers to the “slasher,” Fig. 50, which consists of a line of circular-saws placed 4' 1" apart. This slasher cuts up the slabs into lengths suitable for lath or fence-pickets, Fig. 49. Or they can be resawn into 16" lengths for shingles or fire-wood. From the “slasher” the 4' 1" lengths are carried on by travel¬ ing platforms, chains, etc., to the lath-machines, Fig. 51, where they are sawn up, counted as sawn, bound in bundles of 100, trimmed to exactly 4' in length and sent off to be stored. The shingle bolts are picked off the mov¬ ing platforms by men or boys, and sent to the shingle-machine, Fig. 52, where they are sawn into shingles and dropped down-stairs to Fig - . 49. Ten Saw Gang - Lath-Bolter. This machine cuts up material lengthwise into laths. 40 HANDWORK IX WOOD, Fig-. 50. Slab-Slasher. This machine cuts up the slabs into lengths suitable for lath or fence-piclcets. SAWMILLING. 41 be packed. Shingle-bolts are also made from crooked or otherwise imperfect logs. Of what is left, a good part goes into the grinder or “hog/’ Fig. 53, which chews up all sorts of refuse into small chips suitable for Fig. 51. Combination Lath-Binder and Trimmer. With this machine the op¬ erator can trim the bundles of lath, simply by tilting the packing frame over from hint causing the bundles to pass between the saws, thereby trimming both ends at one movement. Fig. 51. Hand Shingle-Machine This machine is used in Sawmil s in which it is desired to utilize slabs and trimmings by sawing shingles therefrom, or to saw shingles from prepared bolts. fuel to supplement the sawdust if necessary. Band-saws make so little dust and such tine dust that this is often necessary. If there is any refuse that cannot be used at all it goes to the scrap-pile, Fig. 54, or to the “consumer,” the tall stack shown in Fig. 37, see p. 33. Boards ordinarily sawn from logs are “slash-sawn,” i. e., they are tangential or bastard, each cut parallel to the previous one. Bv this process, only the central boards would be radial or “rift” boards But, for a number of reasons, radial boards are better. They warp less because the annual rings cross the board more evenly. Yel¬ low pine flooring that is rift- sawn is more valuable than slash-sawn, because the edge of the annual rings makes a more even grain, Fig. 55. Where slash-grained flooring is used, the boards should be laid so that the outside of each board will be up in order that the in¬ ner rings may not “shell out.” Fig-. 53. Edging-Grinder or Hogr. Itcutsati 3 r kind of wood into coarse or fine chips suitable to be handled by chain conveyor or blower. 42 HANDWORK IN WOOD. In sawing oak for valuable furniture or trim, the log is first “quartered” and then the quarters sawn up as nearly radially as is desired. There are various methods of cutting quartered logs, as illustrated in Fig. 56. In making staves for water-tight barrels, it is essential that they be cut radially in the log, in order that the staves be as non-perme- able to water as possible. Fig. 54. Scrap-Pile, Ocilla, Georgia. Fig. 55. Slash Grain and Comb-Grain Flooring. SAWMILLING. 43 Fig-. 56. Methods of Sawing Quartered Logs. SAWMILLING. References:* Trout, Gassier 11: 83, 184. Woodcraft 5: 56. May ’06. *For general bibliography see p. 4. 44 HANDWORK IN WOOD. Fig'. 57. Lumber-Kiln Chapxek 111. SEASONING. The seasoning of wood is important for several reasons. It re¬ duces weight, it increases strength, it prevents changes in volume after it is worked into shape, and it prevents checking and decay. Decay can also be prevented by submergence and burying, if by so doing logs are kept from fungal attacks. The piles of the Swiss Lake dwellings, which are in a state of good preservation, are of prehistoric age. Wood under water lasts longer than steel or iron under water. But for almost all purposes wood has to be dried in order to be preserved. The wood is cut up, when green, to as thin pieces as will be convenient for its use later, for the rate of drying depends largely upon the shape and size of the piece, an inch board drying more than four times as fast as a four inch plank, and more than twenty times as fast as a ten inch timber. There are various methods of seasoning: (1) Natural or air-seasoning is the most common, and in some respects the best. In this method, the wood is carefully and reg¬ ularly piled in the seasoning-yard, so as to be protected as far as pos¬ sible from sun and rain, but with air circulating freely on all sides of the boards, Fig. 47, p. 38. To accomplish this, “sticking” is em¬ ployed, i. e., strips of wood are placed crosswise close to the ends and at intervals between the boards. In this way the weight of the superposed boards tends to keep those under them from warping. The pile is skidded a foot or two off the ground and is protected above by a roof made of boards so laid that the rain will drain off. Fire-wood is best dried rapidly so that it will check, making air spaces which facilitate ignition, but lumber needs to be slowly dried in cool air so that the fibers may accommodate themselves to the change of form and the wood check as little as possible. Good air- drying consumes from two to six years, the longer the better. 45 46 HANDWORK IN WOOD. (2) Kiln-drying or hot-air-seasoning is a much more rapid pro¬ cess than air-seasoning and is now in common use, Fig. 57 . The drying is also more complete, for while air-dried wood retains from 10% to 20% of moisture, kiln-dried wood may have no more than 5% as it comes from the kiln. It will, however, reabsorb some moisture from the air, when exposed to it. The wood of conifers, with its very regular structure, dries and shrinks more evenly and much more rapidly than the wood of broad¬ leaved trees, and hence is often put into the kiln without previous air-drying, and dried in a week or even less time. Oak is the most difficult wood to dry properly. When it and other hardwoods are rapidly dried without sufficient surrounding moisture, the wood “case-hardens,” that is, the outer part dries and shrinks before the interior has had a chance to do the same, and this forms a shell or case of shrunken, and often checked wood around the interior which also checks later. This interior checking is called honeycombing.* Hardwood lumber is commonly air-dried from two to six months, before being kiln-dried. For the sake of economy in time, the tendency is to eliminate yard-drying, and substitute kiln- drying. Kiln-drying of one inch oak, takes one or two weeks, quarter- sawn boards taking one and a half times as long as plain-sawn. Tbe best method of drying is that which gradually raises the tem¬ perature of both the wood and of the water which it contains to the point at which tbe drying is to take place. Care is therefore taken not to let the surface become entirely dry before the internal moisture is heated. This is done by retaining the moisture first vaporized about the wood, by means of wet steam. When the surface is made permeab'e to moisture, drying may take place rapidly. Curtains of canvas are hung all around the lumber on the same principle that windows in newly plastered buildings are hung with muslin. The moisture is absoibcd on the inner surface of the curtain and evap¬ orates from the outer surface. Improvements in ki’n-drying are along the line of moist air operation. In common practice, however, the moist air principle is often neglected. There are two methods in operation, the progressive method and the charge method. In the progressive, the process is continuous, the loads going in at one end of the kiln, and out at the other, the temperature and the moisture being so distributed in the kiln, that *See Wood and Forest , p. 48. SEASONING. 47 in passing from the green to the dry end, a load of lumber is first moistened, then heated, and finally dried out. In the charge system, the process is intermittent, one charge being removed before a new one is admitted. This gives the best results with high grade lumber for special uses. A modification of hot-air-seasoning is that which subjects the wood to a moderate heat in a moist atmosphere charged with the products of the combustion of fuel. (3) Small pieces of wood may be effectively seasoned by being boiled in water and then dried. The process seems to consist of dis¬ solving out albuminous substances and thus allowing freer evapora¬ tion. Its effect is probably weakening. (4) Soaking in water is sometimes used as a good preparation for air-seasoning. Previous soaking hastens seasoning. Iliver men insist that timber is improved by rafting. It is a common practice to let cypress logs soak in the swamps where they grow for several months before they are “mined out.” They are eagerly sought after by joiners and carpenters, because their tendency to warp is lessened. In tl:e island of Mauritius, ebony is water-soaked as soon as cut. Salt water renders wood harder, heavier, and more durable and is sometimes applied to ship timbers, but should not be used with timbers intended for ordinary purposes, as the presence of salt tends to absoib atmospheric moisture. (5) Boiling in oil is resorted to for special purposes, both for preservation and to give strength. For example, the best handscrews are so treated. The oil also prevents glue from sticking, the most frequent cause of injury to handscrews. (G) There are a number of “impregnation” methods of preserv¬ ing timber, and their practice is spreading rapidly. Of the various preservative processes, those using coal tar creosote and zinc chlorid have proved most efficient. The purpose is to force the preservative into the pores of the wood, either by painting, soaking, or putting un¬ der pressure. Such impregnation methods double or treble the life of railway ties. It is now being used with great success to preserve electric wire poles, mine-props, piling, fence-posts, etc. Wood preservation has three great advantages, it prolongs me life of timbers in use, reduces their cost, and makes possible the use of species that once were considered worthless. For examp'e, the cheap 48 HANDWORK IN WOOD. and abundant loblolly pine can be made, by preservative methods, to take the place of high priced long-leaf pine for many purposes. PRACTICAL SUGGESTIONS FOR STORING LUMBER. Under the hasty methods prevalent in the mill, very little wood conies to the shop well seasoned, and it should therefore be carefully stored before using, so as to have the ful'est possible air circulation around it. Where the boards are large enough, “sticking” is the best method of storage, i. e., narrow strips of wood are placed at short intervals between the pieces which are piled flat. The weight of the boards themselves helps to prevent warping. Boards set upright or on edge are likely to be distorted soon. It is often wise to press to¬ gether with weights or to clamp together with handscrews boards that show a tendency to warp, putting the two concave sides together. Then the convex side is exposed and the board may straighten thus: Fig. 58. By wrapping up small boards in paper or cloth in the inter¬ val between work on them, they may be kept straight un¬ til they are assembled. Another precaution to take is to be sure to plane both sides of a board if either is planed, especially if the board lias been exposed to air-drying for some time. Fig*. 58. Clamping* up Boards to Prevent Warping*. WOOD MEASUREMENTS. Lumber is a general term for all kinds of sawn wood. Logs may be sawn into timber, that is, beams and joists, into planks, which are 2" to 4" thick, or into boards which are from to 1 thick. These may be resawn into special sizes. Lumber is measured by the superficial foot, which is a board 1” thick, 12" wide, and 12" long, so that a board 1" thick, (or 7 /a" dressed) 6" wide and 12' 0" long, measures G' B. M. (board measure). Boards 1" or more thick are sold bv the “board foot” which is equiva¬ lent to 12" square and 1" thick. Boards less than 1" thick are sold by the square foot, face measure. The standard dimensions of sawn SEASONING. 49 lumber are %", 1", 1*4", IV 2 ”, and 2". Any of these may be resawn on a special band saw, or, of course, dressed down to thinner boards. Most dressed lumber comes in sizes 3/16" less than sawn lumber. For example 1" lumber is dressed to 13/16". This rule is followed by nearly all the manufacturers’ associations. In ordering it is common to give the dimensions wanted, in the order of thickness, width, and length, because that is the order in which dimensions are gotten out. E. g.: 6 pcs. quar. oak, /^j"x6"x3' 0" 2 pcs. quar. oak, J4"x7;4"xl5" If a piece wanted is short the way the grain goes, the order would be the same, thus: 34"xll" (wide) x 6" (long). That is, “long” means the way the grain runs. It is always safe to specify in such a case. It is common when small pieces are ordered to add one-quarter to the cost for waste. In large lots lumber is ordered thus: 800' (B. M.) whitewood, dressed 2 sides to 10" and up. This means that the width of any piece must not be less than 10". Prices are usually given per “M,” i. e., per 1000 ft.; e. g.: basswood may be quoted at $40.00 per M. When thin boards are desired it is often economical to buy inch stuff and have it resawn. Some lumber is also ordered by the “running” or lineal foot, es¬ pecially moldings, etc., or by the piece, if there is a standard size as in fence-posts, studs, etc. Laths and shingles are ordered by the bundle to cover a certain area. 1000 4" shingles (=4 bundles) cover 110 sq. ft. with 4" weather exposure. 100 laths (1 bundle) each )4 ” x 1/ / 2"x 4' 0" cover about 150 sq. ft. There are several methods of measuring lumber. The general rule is to multiply the length in feet by the width and thickness in inches and divide by 12, thus: I"x6"xl5'-|-12=7 y 2 feet. The use of the Essex board-measure and the Lumberman’s board-measure are de¬ scribed in Chapter 4, pp. 109 and 111. 50 HANDWORK IX WOOD. THE SEASONING AND MEASURING OF WOOD. References:* SEASONING. For. Dull., No. 41, pp. 5-12, von Sclirenk. Dunlap, Wood Craft, 0: 133, Feb. ’07. For. Circ. No. 40, pp. 10-10, Herty. Barter, pp. 39-53. M EASUEING. Kickels, pp. 22, 29. Goss, p. 12. Boulger, pp. 66-70, 80-88. Wood Craft, 6: 31, Nov. ’06. For. Circ. No. 139. Agric. Yr. Die., 1905, pp. 455-464 Duilding Trades Poclcetbook, 335, 349, 357. Tate, p. 21. pp. For g-eneral bibliography see page 4. Chapter IY. WOOD HAND TOOLS. The hand tools in common use in woodworking shops may, for convenience, be divided into the following classes: 1, Cutting; 2, Boring; 3, Chopping; 4, Scraping; 5, Pounding; 6, Holding; 7, Measuring and Marking; 8, Sharpening; 9, Cleaning. 1. CUTTING TOOLS. The most primitive as well as the simplest of all tools for the dividing of wood into parts, is the wedge. The wedge does not even cut the wood, but only crushes enough of it with its edge to allow its main body to split the wood apart. As soon as the split has be¬ gun, the edge of the wedge serves no further purpose, but the sides bear against the split surfaces of the wood. The split runs ahead of the wedge as it is driven along until the piece is divided. It was by means of the wedge that primitive people obtained slabs of wood, and the great change from primitive to civilized meth¬ ods in manipulating wood consists in the substitution of cutting for splitting, of edge tools for the wedge. The wedge follows the grain of the wood, but the edge tool can follow a line determined by the worker. The edge is a refinement and improvement upon the wedge and enables the worker to be somewhat independent of the natural grain of the wood. In general, it may be said that the function of all cutting tools is to separate one portion of material from another along a definite path. All such tools act, first, by the keen edge dividing the material into two parts; second, by the wedge or the blade forcing these two portions apart. If a true continuous cut is to be made, both of these actions must occur together. The edge must be sharp enough to enter between the small particles of material, cutting without bruising them, and the blade of the tool must constantly force apart the two portions in order that the cutting action of the edge may continue. The action of an ax in splitting wood is not a true cut, for only 51 52 HANDWORK IN WOOD. the second process is taking place, Fig. 59. The split which opens in front of the cutting edge anticipates its cutting and therefore the surfaces of the opening are rough and torn. When a knife or chisel is pressed into a piece of wood at right angles to the grain, and at some distance from the end Fig. GO, a action is soon the ajrart the of the wood, as continuous prevented, because blade cannot force m cutting Fig-. 59. Wedge Action. Fig. 60 Edge Action. sides of the cut made by the advancing edge, and the knife is brought to rest. In this case, it is practically only the first action which has taken place. Both the actions, the cutting and the splitting, must take place together to produce a true continuous cut. The edge must always be in contact with the solid material, and the blade must always be pushing aside the portions which have been cut. This can happen only when the material on one side of the blade is thin enough and weak enough to be readily bent out of the way without opening a split in front of the cutting edge. This cutting action may take place either along the grain, Fig. 61, or across it, Fig. 62. The bending aside of the shaving will require less force the smaller the taper of the wedge. On the other hand, the wedge must be strong enough to sustain the bending resistance and also to sup¬ port the cutting edge. In other words, the more acute the cut¬ ting edge, the easier the work, and hence the wedge is made as thin as is consistent with strength. This varies all the way from hollow ground raz¬ ors to cold-chisels. For soft wood, the cutting angle (or bevel, or bezel) of chisels, gouges and plane-irons, is small, even as low as 20°; for hard wood, it must be greater. For metals, it varies from 54° for wrought iron to 66° for gun metal. Fig-. 61 Fig-. 62 Edge and Wedge Ac- Edge and Wedge Ac¬ tion With the Grain, tion Across the Grain. WOOD HAND TOOLS. 53 Ordinarily a cutting tool should be so applied that the face near¬ est the material lies as nearly as possible in the direction of the cut desired, sufficient clearance being necessary to insure contact of the actual edge. There are two methods of using edge tools: one, the chisel or straight cut, by direct pressure; the other, the knife or sliding cut. The straight cut, Fig. 63, takes place when the tool is moved into the mate¬ rial at right angles to the cutting edge. Examples are: the action of metal¬ working tools and planing machines, rip-sawing, turning, planing (when the plane is held parallel to the edge of the board being planed), and chiseling, when the chisel is pushed directly in line with its length. The knife or sliding cut, Fig. 64, takes place when the tool is moved for¬ ward obliquely to its cutting edge, either along or across the grain. It is well illustrated in cutting soft mate¬ rials, such as bread, meat, rubber, cork, etc. It is an advantage in delicate chiseling and gouging. That this sliding action is easier than the straight pressure can easily be proved with a penknife on thin wood, or by planing with the plane held at an angle to, rather than in line with, the direction of the planing motion. The edge of the cutter then slides into the material. The reason why the sliding cut is easier, is partly because the angle of the bevel with the wood is reduced by holding the tool obliquely, - and partly because even the sharpest cutting edge is notched with very fine teeth all along its edge so that in the sliding cut it acts like a saw. In an auger-bit, both methods of cutting take place at once. The scoring nib cuts with a sliding cut, while the cutting lip is thrust directly into the wood. The chisel and the knife, one with the edge on the end, and the other with the edge on the side, are the original forms of all modern cutting tools. The chisel was at first only a chipped stone, then it came to be a ground stone, later it was made of bronze, and still later of iron, and 54 HANDWORK IN WOOD. Fiy. 05. Firmer-Chisel. now it. is made of steel. In its early form it is known by archeolo¬ gists as a celt, and at first had no handle, but later developed into the ax and adze for chopping and hewing, and the chisel for cuts made by driving and paring. It is quite likely that the celt itself was simply a development of the wedge. In the modern chisel, all the grinding is done on one side. This constitutes the essential feature of the chisel, namely, that the back of the blade is kept perfectly flat and the face is ground to a bevel. Blades vary in width from 1/1G inch to 2 inches. Next to the blade on the end of which is the cutting edge, is the shank, Fig. G5. Next. as in socketed chisels, there is the socket to receive the handle, or, in tanged chisels, a shoulder and four - sided tang which is driven into the handle, which is bound at its lower end by a ferrule. The handle is usually made of apple wood. The most familiar form is the firmer-chisel. Fig. 65, which is said to get its name from the fact that it is firmer or stiffer than the paring-chisel. (See below.) The firmer- chisel is a general utility tool, being suited for hand pressure or mallet pounding, for paring or for light mor¬ tising. Different varieties of chisels are named; (1) according to their uses; as paring-chisels, framing-chisels, mortise- chisels, carving-chisels, turning-chisels, etc. The paring-chisel. Fig. 66, has a handle specially shaped to give control over its movements, and a long thin blade, which in the best form is beveled on the two edges to facilitate grooving. WOOD HAND TOOLS. 55 It is intended only for steady pressure with the Land and not for use with a mallet. The framing-chisel. Fig G7, is thick and heavy and was formerly much used in house flaming. It is usually made with the handle fitting into a socket on the shank, in order to withstand the shock of heavy blows fiom the mallet. The mortise-cliisel, Fig. G8, is made abnormally thick to give the stillness necessary for levering the waste out of mortises. (2) Chise’s are also named according to their shapes; as, skew-chisels, corner-chisels, round-nosed chisels, etc. The angle of the bevel of a ciiisel is determined by the kind of wood for which it is most used, hard wood requiring a wider angle than soft wood, in order to support the edge. For ordinary work, the bevel is correctly ground to an angle of about 20“. The chisel is a necessary tool in making almost every kind of joint. It may almost be said that one mark of a good workman is his pref¬ erence for the chisel. Indeed an excellent motto for the woodworker is: “When in doubt, use a chisel'’. In general, there are two uses for the chisel (1), when it is driven by a push with the hand, as in paring, and (2), when it is driven by blows of a mallet, as in digging mortises. In relation to the grain of the wood, it is used in three directions: (1) longitudinally, that is with the grain, called paring; (2) laterally, across the surface, called cutting sidewise; (3) transversely, that is across the end, called cutting end-wood. 1. Paring. To remove shavings rapidly, the chisel is held flat side up, the handle grasped by the right hand, with the thumb pointing toward the shank, and the blade held in the left hand, as in Fig. G9. Held in this way great control can be exerted and much force applied. For paring the surface as flat and smooth as possible, the chisel should be reversed, that is, held so that the flat side will HANDWORK IN WOOD. 56 act as a guide. Held m this way the chisel has no equal for paring except the plane. Paring with the chisel is the method used in cutting stop chamfers. (See p. 184.) By holding the cutting edge £Fig. 70; Chiseling-Out a Dado (First Step). obliquely to the direction of the grain and of the cut, the effective “sliding cut” is ob¬ tained, Fig. 64. Fig. 71. Chiseling Out a Dado (Second Step). 2. In sidewise chiseling the chisel is held in the same manner as in paring. A typical form of sidewise chiseling is the cutting out of a dado, Fig. 70. The wort Fig 1 . 12 ,. Perpendicular Chiseling - . may be placed on the bench-hook or held in the vise, with the side up from which the groove is to be cut. The chisel is pushed directly across the grain, the blade being somewhat inclined to the upper surface so as to cut off a corner next the saw kerf. After a few cuts thus made with the chisel inclined alternately both ways, the ridge thus formed is taken off, Fig. 71. In this way the surface is lowered to the required depth. If more force be required, the palm of the hand may be used as a mallet. 3. In chiseling end-wood, it is well, if possible, to rest the piece to be trimmed flat on the cutting board or on a piece of waste wood. Work done in this way is often called per¬ pendicular chiseling, Fig. 72. The handle is grasped in the right hand. WOOD HAND TOOLS. CW thumb up, while the blade of the chisel passes between the thumb and first finger of the left hand, the back of which rests on the work and holds it in place. As the right hand pushes the chisel downwards the thumb and first finger of the left hand control its motion. When chis¬ eling it is well to stand so as to look along the line being cut. Incline the chisel to¬ ward you, and use the near part of the cutting edge for a guide and the farther corner for cutting, pushing the handle both down and toward you at the same time, Fig. 73. Or, by pushing the chisel sidewise with the thumb of the left hand at the same time that the right hand pushes it down¬ ward, the effective sliding cut is obtained. End chiseling requires considerable force and therefore only thin shavings Fig - . 73. Chiseling - End Wood. Fig - . 74. Paring - a Corner Round the work down tight with a handscrew to a perfectly smooth cutting board. It is often advisable however, to set the piece upright in the vise and pare off thin shavings horizontally, Fig. 74. In rounding a corner, both this and per¬ pendicular chiseling are common meth¬ ods. In both cases care should be taken to cut from the side toward the end and not into the grain, lest the piece split. Fig. 75. In horizontal end par- should be cut off at a time. Or the mallet may be used with caution. In order to leave a smooth surface the chisel must be very sharp. Even then the lower arris (corner) is likely to be splin¬ tered off. This can be prevented by clamping Fig-. 75. Rig-tit and Wrong Ways of Perpendicular Chiseling. HANDWORK IN WOOD. 58 ing, Fig. 74, in order to prevent splin¬ tering, it is well to trim down the arrises diagonally to the line and then to re¬ duce the rest of the end surface. In all hand chiseling, it is a wise precaution not to try to cut out much material at each stroke but to work back gradually to the line. A typical form of mallet chiseling is the digging of a mortise, Fig. 76. (See also p. 56.) The chisel is held perpen¬ dicular in the left hand, while the right hand drives blows with the mallet. The hammer should never be used. (See mallet, p. 96.) By rocking the chisel and at the same time giving it a twisting motion while the edge is kept on the wood, the edge can be stepped to the exact place desired. Care should be taken to work back to the lines gradu¬ ally, to cut only part way thru from each side (in the case of a thru mor- tise-and-tenon), and to keep the cut faces perpendicular to the surfaces. In sharpening a chisel it is of first importance that the back be kept perfectly flat. The bevel is first ground on the grindstone 7b. Mallet Chiselin; Tlie Piece Clamped Down on ilie Bench With the Bench-Hook. to an angle of about 20°, and great care should be taken to keep the edge straight and at right angles to the sides of the blade. (See also p. 117.) After grinding it is nec¬ essary to whet the chisel and other edged tools. (See also under oilstones, p. 121.) First see that there is plenty of oil on the stone. If an iron box be used. Fig. 77, the oil is obtained sim¬ ply bv turning the stone Whetting a Plane-Bit. WOOD HAND TOOLS. 59 over, for it rests on a pad of felt which is kept wet with kerosene. Place the beveled edge flat on the stone, feeling to see if it does lie flat, then tip up the chisel and rub it at an angle slightly more obtuse than that which it was ground, Fig. 78. The more nearly the chisel can be whetted at the an¬ gle at which it was ground the better. In rubbing, use as much of the stone as possible, so as to wear it down evenly. The motion may be back and forth or spiral, but in either case it should be steady and not rocking. This whetting turns a light wire edge over on the flat side. In order to remove this wire edge, the back of the chisel, that is, the straight, unbeveled side, is held perfectly flat on the whetstone and rubbed, then it is turned over and the bevel rubbed again on the stone. It is necessary to reverse the chisel in this way a number of times, in order to remove the wire edge, but the chisel should never be tipped so as to put any bevel at all on its flat side. Finally, the edge is touched up (stropped) by being drawn a few times, first on one side, then on the other, over a piece of leather, still continuing to hold the chisel so as to keep the bevel perfect. To test the sharpness of a whetted edge, draw the tip of the finger or thumb lightly along it, Fig. 79. If the edge be dull, it will feel smooth; if it be sharp, and if care be taken, it will score the skin a little, not enough to cut thru, but just enough to be felt. The gouge is a form of chisel, the blade of which is concave, and hence the edge curved. When the bevel is on the outside, the common form, it is called an outside bevel gouge or simply a “gouge,” Fig. 80; if the bevel is on the inside, it is called an inside bevel, or inside ground, or scribing-gouge, or paring-gouge, Fig. 81. 3 3 Another confusing nomenclature (Goss) gives the name “inside gouges” to those with the cutting edge on the inside, and “outside gouges” to those with the cutting edge on the outside. Fig - . 78. Grinding- Angle, 20° Whetting- Ang-le, 25°. HANDWORK IN WOOD. Carving tools are, properly speaking, all chisels, and are of different shapes for facility in carving. For ordinary gouging, Fig. 82, the blade is gripped firmly by the left hand with the knuck¬ les up, so that a strong control can be exerted over it. The gouge is manipulated in much the same way as the chisel, and like the chisel it is used longitudinally, laterally, and transversely. In working with the grain, by twisting the blade on its axis as it moves forward, delicate paring cuts may be made. This is particularly necessary in working cross-grained wood, and is a good illustration of the advantage of the slid¬ ing cut. In gouging out broad surfaces like trays or saddle seats it will be found of great advantage to work laterally, that is across the surface, especially in even grained woods as sweet gum. The tool is not so likely to slip off and run in as when working with the grain. The gouge that is commonly used for cutting concave outlines on end grain, is the inside bevel gouge. Like the chisel in cutting convex outlines, it is pushed or driven perpendicularly thru the wood laid flat on a cutting board on the bench, as in perpendicular chiseling, Fig. 72, p. 56. In sharpening an outside bevel gouge, the main bevel is obtained on the grindstone, care being taken to keep the gouge rocking on its axis, so as to get an even curve. It is then whetted on the flat side of a slipstone, Fig. 83, the bevel already obtained on the grindstone being made slightly more obtuse at the edge. A good method is to rock the gouge on its axis with the left hand, while the slipstone held in the right hand is rubbed back and forth on the edge. Then the concave side is rubbed on the round edge of Fig-. 82 . Gouging-. (30 Gouge Out- Bevel side Bevel. Gouge. WOOD HAND TOOLS. 61 the slipstone, care being taken to avoid putting a bevel on it. Inside bevel gonges need to be ground on a cone-shaped or round edge carborundum wheel or other revolving stone having a round edge. The outfit of the agacite grinder, (Fig. 224, p. 120), contains one of these stones. The whetting, of course, is the reverse of that on the outside bevel gouge. The Tcnife differs from the chisel in two respects, (1) the edge is along the side instead of the end, and (2) it has a two-beveled edge. Knives are sometimes made with one side flat for certain kinds of paring work, but these are uncommon. The two-beveled edge is an advantage to the worker in enabling him to cut into the wood at any angle, but it is a disadvan¬ tage in that it is incapable of making flat surfaces. The knife is particularly valuable in woodwork for scoring and for certain emergencies. The sloyd knife, Fig. 84, is a tool likely to be misused in the hands of small children, but when sharp and in strong hands, has many valuable uses. A conveni¬ ent size has a 2)4 inch blade. When grinding and whetting a knife, the fact that both sides are beveled alike should be kept in mind. The draw-knife , Fig. 85, is ground like a chisel, with the bevel only on one side, but the edge is along the side like a knife. Instead Fig-. 84 Sloyd Knife 62 handwork; in wood. of being pushed into the wood, like a chisel, it is drawn into it by the handles which project in advance of the cutting edge. The handles are sometimes made to fold over the edge, and thus protect it when not in use. The size is indicated by the length of the cutting edge. It is particularly useful in reducing narrow surfaces and in slicing off large pieces, but it is liable to split rather than cut the wood. SAWS. The object of the saw is to cut thru a piece of material along a determined line. Its efficiency depends upon (1) the narrowness of the saw cut or “kerf,” and (2) upon the force required to drive it thru the material. The thinner the blade, the less material will be cut out and wasted, and the less force will have to be applied. In order to have the saw as thin as possible, almost all the people of the world, except the Anglo Saxons, have saws that cut when they are pulled toward the worker. The blade is in tension while cutting and in compression only when being returned for a new cut. German carpenters use a saw like our turning-saw. English and Americans have developed the saw on the opposite principle, namely, that it should cut on the pushing stroke. As a matter of fact, the crosscut- saw cuts somewhat on the back stroke. The pushing stroke necessi¬ tates a thickening of the blade sufficient to prevent buckling,—a not uncommon occurrence in the hands of a novice, in spite of this thick¬ ening. But tho this requires more force, and involves more waste, there are the compensations that the arm can exert more pressure in pushing than in pulling, especially when the worker stands upright or stoops over his work, and the stiffer wide blade acts as a guide to the sawyer. Each method has its advantages. Whatever may be true of hand-saws, in machine-saws the tension method, as illustrated by the gang-saw and the band-saw, is steadily displacing the compres¬ sion method utilized in the circular-saw. Many kinds of work, how¬ ever, can be done only on the circular-saw. In order to diminish the disadvantages of the thrusting stroke, the modern hand-saw, Fig. 86, has been gradually improved as the re¬ sult of much experience and thought. The outline of the blade is tapered in width from handle to point; it is thicker also at the Fig - . 8b Hand-Saw. WOOD HAND TOOLS. 63 heel (the handle end) than at the point; its thickness also tapers from the teeth to the back. All these tapers gives stiffness where it is most needed. It is made wide for the sake of giving stead¬ iness in sawing. The fact that it is thinner at the back than along the teeth gives it clearance in passing back and forth in the kerf, but the friction is still great, especally in sawing soft or damp wood. To avoid this binding still further, the teeth are “set” alternately one to one side and the next to the other, and so on. ^ r ^ ^ ^ ^ _Fw . ha. tw [.-.-I N. U A A' fi- . l' .>1 / Fig-. 87. Rip Saw Teeth: A-edge view, B-side view, C cross-section. Crosscut-Saw Teeth: A' -edge view, B' -side view, C' -cross-section. The size of saws is indicated by the length of the blade in inches. The coarseness of the teeth is indicated by the number of “points” to the inch stamped on the face of the blade. “Points” should not be confused with teeth as there is always one more point per inch than there are teeth. For example, a five point rip-saw has five points to the inch but only four full teeth, Fig. 87. Rip-saws run from 4 to 7 points per inch; crosscut-saws from 6 to 12 points per inch. In general, saws are of two kinds, rip-saws and crosscut-saws. The rip-saw , Fig. 87, may be thought of as a series of chisels set in two parallel rows which overlap each other, for each tooth is filed to a sharp edge wtiich, at each stroke, chisels off a small particle from the end of the wood fibers. The shape of the teeth is the result of experience in uniting a number of factors: as, strength of the individual tooth, the acuteness of the cutting angle, and the ease of sharpening. The steel of a saw is softer than that of a chisel, in order that it may be filed and set. Hence it is weaker and the edge cannot be so acute. A typical form of tooth is shown in Fig. 87, in which A is an edge view, B the side view, and C a cross section. The angle of each tooth covers 60°, one side, the “face”, being at right angles to the line of the teeth. The cutting edge runs at right angles to the sides of the blade. This arrangement works with entire success along the grain, but if a rip-saw is used to cut across the grain, since there is no provision 61 HANDWORK IN WOOD. for cutting thru the fibers, each tooth catches in them and tears them out, thus leaving a rough and jagged surface. In the crosscut-saw, therefore, the teeth are filed to points, and the cutting edge is on the forward side of each alternate tooth. In Fig. 87, A' is the edge view, B' is the side view and C' is a cross-sec¬ tion. In a properly filed crosscut-saw a needle will slide between these two rows of teeth from one end of the saw to the other. I n action the points, especially their forward edges, cut or score the fibres of wood, and then the tri¬ angular elevation of wood left between the two rows of points is crumbled off by fric¬ tion as the saw passes thru. Thus it drops farther and farther into the cut. A crosscut-saw may be thought of as a series of knife points, ar¬ ranged in two parallel rows. Ordinarily the angle of the “face” of each tooth with the line of the teeth is about 65°, and slightly steeper than the back of the tooth. The angle of the cutting edge of each tooth may be filed more acute when the saw is to be used for soft wood only. A crosscut-saw when used to rip a board, works slowly, for there is no chisel action to cut out the fibres between the points, but the cut, tho slow, is smooth. In cutting diagonally across a piece of wood, especially soft wood, a rip-saw cuts faster, but a crosscut, smoother. In ripping a board, allowance should always be made for planing to the line afterward. In starting a cut with the rip-saw, the weight of the saw should be borne by the right hand so that the teeth may WOOD HAND TOOLS. 65 pass over the edge of the wood as lightly as possible. The left thumb acts as a guide. If the saw be handled thus, and the angle with the board be quite acute, it is not necessary to start with a back stroke. When the kerf is well started, the whole weight of the saw may be applied. An easy light stroke is better than a furious one. The line should be followed carefully, but if the saw runs from the line it may be brought back by taking short strokes near the point of the saw and twisting the blade slightly in the desired direction. If the saw binds and buckles because of the springing together of the wood, the kerf may be wedged open with a screwdriver or a bit of waste wood. A drop of oil rubbed across each side of the saw will make it work more easily. Care should be taken in finishing a cut to hold up firmly the part of the wood which is being sawn off so that it will not split off or splinter. Sawing may be done either on a saw¬ horse, Fig. 88, or at a bench. For big, rough work, the for¬ mer is the common way, the worker holding the material in place with one knee, because this method enables him to exert his greatest strength. A convenient way for rip-sawing a small piece of wood is to insert it in the vise, Fig. 89, with the broad side of the board parallel to the vise screw, and the board inclined away from the worker who stands upright. The start is easy, the sawdust does not cover the line, and the board is not in danger of splitting. The board, however, has to be reversed after it is sawn part way thru, in order to finish the saw cut. The 'bac'k-saw or tenon-saw, Fig. 90, is a fine crosscut-saw, with a rib of steel along the back, which gives to it its name. Since it is intended for small accurate work, the teeth have little or no set. In sawing, the wood may be held either in the vise or on the bench-hook. To help start the saw and at the same time to keep the edges of the cut sharp, it is well to make a little groove Fig'. 89. Rip-sawing- with Wood Held in Bench-Vise. 66 HANDWORK IN WOOD. with the knife, on the waste side of the line to be followed, cutting the side of the groove next to the line at right angles to the surface. The saw drops directly into this groove, Fig. 91. In starting the saw cut, the saw should be guided by holding the thumb of the left hand against the side of the saw just above the teeth. Until the kerf is well started, the saw should be held so that the teeth just touch the wood. It is better not to attempt to start the saw level, i. e., with the teeth resting clear across the wood, but the handle should be raised so that the start is made only at the farther edge of the wood. Then as the Fig - . 90. Using - the Back-Saw with Bench-Hook. saw is gradually lowered, the kerf will extend quite across the wood, Fig. 92. When the back-saw is used for ripping, the wood is held in the vise, end up. Begin sawing as in crosscutting, that is, at the farther corner wdth the handle end of the saw up, and gradually drop the handle. Watch the lines on both the front and back sides, and if neces¬ sary, reverse the piece to follow them. The dovetail-saw , Fig. 93, is a small back-saw for delicate work. The compass-saw, Fig. 94, is narrow, pointed, thick, to prevent Fig-. 91. Starting a Saw Cut in a Trough Cut With Knife. Fig. 92. Direction of the Back-Saw. Fig. 94. Compass-Saw. WOOD HAND TOOLS. 67 buckling, and with a wide set to the teeth, to help in following the curves. The teeth are a cross between the rip and crosscut teeth. It is used in sawing curves. The turning-saw. Fig. 95, is a narrow saw, set in a frame, which stretches the saw tight, so that it works as a tension saw (cf. p. 62. The best frames are made so that the handles which hold the blade can revolve in the frame. The turning-saw is used chiefly for cutting curves. A 14 inch blade, 3/16 of an inch wide is a good size for ordinary use. The teeth are like those of a rip-saw, so that they are quite likely to tear the wood in cutting across the grain. Al¬ lowance should be made for this and the surplus removed with a spokeshave. The turning-saw may be used to cut on either the pulling or the pushing stroke, with the teeth pointed either toward or away from the worker. The pulling cut is generally better, as it puts less strain on the frame than the pushing cut. Both hands should grasp the frame as near the end of the blade as possible, Fig. 95. Turns are made by revolving the frame on the blade as an axis, which should always be kept at right angles to the surface of the board. Care should be taken not to twist the blade. To file and set a saw, the saw is first fastened i n Fig-. 96. Saw-Vise. HANDWORK IN WOOD. 68 the saw-vise, Fig. 96, with the teeth up. It is then top-jointed by running a flat file or a saw-jointer, Fig. 97, back and forth length¬ wise along the tops of the teeth to bring them to a level. After jointing the saw should be set. For this purpose a saw- set, Fig. 98, is necessary. Ev¬ ery alternate tooth is bent in the direction of its set by the plunger in the instrument pushing against the anvil, which is an adjustable eccentric disc. After the saw is set, it is filed. This is done with a triangular file, Fig. 144, p. 90, which is held in the right hand and its point in the thumb and fingers of the left. Pressure is applied only on the forward stroke, which should be long and even, the file being raised above the tooth on the return stroke. The file should cut in the direction of the set, that is, the teeth having the set away from the worker are filed first. Every alternate tooth, 1st, 3d, 5th, etc., is filed, and then the saw is reversed and the other set, the 2d, 4th, 6th, etc., is filed. In filing a rip-saw the file should move exactly perpendicularly to the plane of the saw blade, that is, directly across the teeth. The filing is done on the back of the teeth, the file just touching the face of the next one. The filing is continued, with one, two, or three strokes, for each tooth, as the case may require, or just until each tooth is sharp. In filing a crosscut-saw, the file is held pointing upward and to¬ ward the point of the saw. The file should cut in the direction of the set. The angle of the cutting edge is determined by the hori¬ zontal inclination of the file to the blade; the angle of the point is determined by the perpendicular inclination of the file to the blade. Finally the sides of the teeth are rubbed lightly with a slipstone to remove the wire edge. It should always be remembered that a saw is an edge tool, and its edges are as liable to injury as any edges. WOOD HAND TOOLS. 69 PLANES. The plane is a modified chisel. The chief difference in action between a chisel and a plane in paring is this: the back of the chisel lies close down on the surface of the wood that is cut, and acts as a guide; whereas, in the plane, the cutter is elevated at an angle away from the surface of the wood, and only its cutting edge touches the wood, and it is held and guided mechanically by the plane mechan- Fig 1 . 99. Adjustable Chisel-Gage. Fig. 100. Wooden Bench-Plane. ism. In other words, a plane is a chisel firmly held in a device which raises the cutter at an angle from the work, regulates the depth of the cut, and favors the cutting rather than the splitting action. An illustration of a chisel converted into a plane is the adjustable chisel- gage, Fig. 99. The plane has developed as follows: it was first a chisel held in a block of wood. This is all that oriental planes are now, simply a sharpened wedge driven into a block of wood. When the hole works too loose, the Japanese carpenter inserts a piece of paper to tighten it, or he makes a new block. The first improvement was the addition of a wooden wedge to hold in place the “plane-iron”, as the cutter was formerly called. In this form, the cutter or plane-iron, tho still 70 HANDWORK IN WOOD. wedge-shaped, was reversed, being made heavier at the cutting edge in order to facilitate fastening it in the wooden plane-stock by means of the wooden wedge. Then a handle was added for convenience. Then came the cap, the object of which is to break back the shaving and thus weaken it as soon as possible after it is cut. Until a few years ago, this was all that there was in a plane, and such planes are still common, Fig. 100. Finally there appeared the iron plane. Fig. 101, with it various mechanical adjustments. The following are the parts of the Bailey iron plane : 4 1. Cutter, or bit, or blade, or plane-iron. 2. Cap, or plane-iron cap, or curling iron. 3. Cutter screw, or plane-iron screw. 4. Clamp, or lever cap, or wedge. 5. Clamp screw, or cap screw. C. Frog. 7. Y Adjustment. 8. Brass set screw, or brass adjusting nut. 9. Lever (for lateral adjustment). 10. Frog screw. 11. Handle. 12. Knob. 13. Handle bolt and nut. 14. Knob screw, or Knob bolt and nut. 15. Handle screw. 16. Bottom, or sole. 17. Toe. 18. Heel. 19. Throat. 20. Thumb piece, or clamp lever, or cam. There are various principles involved in the action of the plane The effect of the flat sole is to regulate the cut of the cutter. If the surface be uneven, the cutter will not cut at all, or but little, in pass¬ ing over low places, since the toe and heel of the sole will then be resting on higher places; but when the cutter reaches a high place a shaving will be taken off. Hence it follows that the longer the plane, the straighter will be the surface produced. The length of the plane used is determined by the length of the wood to be planed, and the degree of straightness desired. 4 The numbers and names in italics are those given in Stanley’s Catalog No. 34. Some of these names, as “plane-iron,” are survivals from the days of the wooden plane and are obviously unsuitable now. WOOD HAND TOOLS. 71 The part of the sole directly in front of the cutter presses firmly down on the wood and so prevents the shaving from splitting far in advance of the edge. It follows that the narrowness of the throat in a plane is an important factor in the production of smooth sur¬ faces. This can be regulated by adjusting the toe in the block-plane, and by moving the frog in the jack- and smooth-planes. A recent improvement in jack-, smooth-, and fore-planes consists of an adjustable frog, by means of which the throat can be narrowed or widened at will by means of a set-screw in the rear of the frog without removing the clamp and cutter. It is made by the Stanley Rule and Level Company and is called the “Bed-Rock’'’ plane. The splitting of the wood in advance of the edge is also prevented by the breaking of the shaving as it hits against the cutter or its cap. Hence the advantage of bending up and breaking or partly breaking the shaving as soon as possible after it is cut. This shows why the cap is set close to the edge of the cutter. Another reason is that it thereby stiffens the cutter and prevents “chattering.” If a thick shav¬ ing be desired the cap has to be set far¬ ther back. In a smooth-plane 1/32 inch is enough, in a jack-plane 1/8 inch is often desirable. The following are the planes in common use: The jack-plane , Fig. 102, 14" to 15" long, is the one used where a consider¬ able amount of material is to be taken off to bring a piece of wood to size, and therefore the outline of the cutting edge instead of being straight is slightly curved or “crowned” so that in planing the surface of a board it makes a series of shallow grooves, the ridges of which must afterward be smoothed off by an¬ other plane. Also for beginners whose hands are not strong it is sometimes wise to grind the cutter with some “crown”, in order to take off narrow shavings, which require less strength. For school use, where the jack-plane is used for all purposes, the cutter Fig - . 102- Sighting Along the Sole of Jack-Plane. HANDWORK IN WOOD. is usually ground almost straight and only the corners rounded as in the smooth-plane and the fore-plane. 5 The fore-plane 18" to 20" long, and the jointer, 22" to 30 long, are large planes, similar to the jack-plane, except that the cutting edge is straight. They are used for straightening and smoothing long pieces. The smooth-plane, 5 1 / 2 " to 10" long, is a short plane, similar to the jack-plane, except that the cutting edge is straight. It is used for smoothing. These four planes, the jack-plane, the fore-plane, the jointer, and the smooth-plane, are essentially alike, and directions for the use of one apply to all. There are two chief adjustments in the Bailey iron plane: the bi'ass set-screw, see 8 in Fig. 101, which, by moving the adjustment up or down, regulates the depth of the cut, and the lever, 9, which moves the cutter sidewise so that it may be made to cut evenly. The skilful worker keeps constant watch of these adjustments. It is well to form the habit of always sighting along the sole before beginning to plane, in order to see that the cutter projects properly, Fig. 102. It is a common mistake among beginnenrs to let the cutter project too far. It is important to know what is the best order of procedure in planing up a board. There are often reasons for omitting the plan¬ ing up of one or more surfaces, but it is wise to form the habit of following a regular order, and the following is suggested as a good one: 1. Working face. Plane one broad side flat and smooth. Finish with the plane set to cut fine shavings. Test with try-square. Mark this face with a distinct pencil mark, A, Fig. 103. 2. Working edge. Plane one narrow side straight and square with the working face. Test with try-square, pressing the block of the try-square against the working face. Mark the working edge with two distinct pencil marks, B, Fig. 103. 3. End. First mark the width on the working face with the marking-gage, C, 1-2, Fig. 103. Chisel off the corner, a, of the piece outside this gaged line. True and smooth this end with the plane, making it square with both working face and working edge, D, 2, 3, 4, Fig. 103. 4. Length. Measure the length from the finished end, D, 2-3-4, score across the working face, D, 5-6, and working edge, D, 6-7, 5 In whetting a plane-bit, a slight crown may be given it by rubbing a bit harder at the ends of the edge than in the middle. Strop in the same way as a chisel (p. 59). WOOD HAND TOOLS. 73 using a sharp knife point and the try-square. Saw just outside this line, D, 5-6-7, with the back-saw, cut off the narrow corner, D, 1), beyond the gaged line and plane true, E, Fig. 103. 5. Width. Plane to the center of the gaged line, E, 1-2. Test this edge from the working face, F, Fig. 103. 6. Thickness. Mark the thickness with the marking-gage all around the piece, F, 8-9-10. Plane to the center of the gaged line, 6, Fig. 103. Test this face for flatness. 74 HANDWORK IN WOOD. In a word, the order to be followed is graphically represented in H, Fig. 103. The surfaces are numbered consecutively in the order in which they are to be planed. The advantages of this order are these: by planing the working face first, a broad surface is secured to which the others may be made true. By planing the ends before the width is planed, the danger of splitting off fragments can be avoided by chisel¬ ing the corner of the unfinished edges, C, a, and D, b, Fig. 103, into a buttress. By planing the ends and the width be¬ fore the thickness is planed, a dressed face is secured all around for gaging the thickness. In following this order all measurements and markings are made on a dressed face. If there be any “wind 55 or twist in the board, this should be discovered first of all. This may be done roughly by sight¬ ing across the broad side of the board, Fig. 104, and more accurately by the use of “winding sticks, 55 see Fig. 205, p. 113. Or the surface may be tested with the plane itself by tilting the plane on its long corner edge, and resting it on the board, while the worker looks between the board and the plane toward the light. It is evident that the plane must be turned in various directions to test for wind, and that a board only as long or as wide as the plane is long can be tested in this way. The try-square or any straight edge may be used for the same purpose, Fig. 105. If there be any wind in the board, this should at once be taken out of one face by planing down the high corners. In starting to plane, the worker should bear down on the knob at the front end of the plane. When the plane is well on the board, he should bear down equally on both Fig. 104. Sighting for Wind. Fig. 105. Testing from Edge to Edge. WOOD HAND TOOLS. I 0 knob and handle, and as the plane begins to pass off the board he should put all the pressure on the handle end, Fig. 106. By taking pains thus, a convex surface will be avoided, the making of which is a common error of be¬ ginners. On the return stroke, the plane should be lifted or tilted so that the cutting edg* 3 will not be dulled by rubbing on the wood. This is especially important on rough and dirty boards, as it saves the cutting edge, and in fine work, as it saves the work. If the plane tear the wood instead of cutting it smooth, as it should, it is because the planing is “against the gjain”. This can often be avoided by noticing the direction of the grain before begin¬ ning to plane. But even if it be not noted beforehand, a stroke or two will show the roughness. In such a case, it is necessary simply to turn the wood around. The accuracy of the work as it progresses should frequently be tested, and the eye should constantly be trained so that it can more and more be depended upon to detect inaccuracy, Fig. 107. As each surface is trued, it should be carefully smoothed with the cutter set to cut fine shavings. In planing a very cross-grained piece of wood, there are several methods to use for securing a smooth surface. The frog of the plane should be moved forward so that the throat in the front of the cutter is a mere slit. In the ordinary plane it is necessary to remove the cutter in order to reset the frog, but in the Sargent plane and the Stanley “bed rock” plane, it can be set by a set-screw at the rear of the frog. Next, the cap should be set so that the cutter projects but very little beyond it, or, in technical language, the cutter should be set “fine.” A sliding cut, see p. 53, should be taken with the plane, and sometimes it may be nec¬ essary to move the plane nearly at right angles to the general direction Fig. 107. Sighting an Edge. Fig. 10b. Planing an Edge. 76 HANDWORK IN WOOD. of the grain. By these means even refractory pieces of wood can be well smoothed. See also scrapers, p. 91. The choking of a plane is the stoppage of the throat by shavings. It may be due simply to the fact that the cutter is dull or that it projects too far below the sole of the plane. In a wooden plane chok¬ ing is sometimes due to the crowding of shavings under some part of the wedge. When the adjustable frog in a modern plane is improperly placed choking may result. The frog should be far enough forward so that the cutter rests squarely upon it. Choking may, and most commonly does, take place because the cap does not fit down tight on the cutter. This happens if the cap be nicked or uneven. In consequence, minute shavings are driven between these two irons and choking soon results. The remedy is to sharpen the cap, so that its edge makes a close fit with the cutter. The fit may be made still tighter by rubbing with a screwdriver the edge of the cap down on the cutter after it is screwed in place. In no tool is it more important to keep the cutter sharp than in the plane. To remove the cutter, in order to sharpen it, first loosen the clamp lever and remove the clamp. Carefully remove the cap and cutter taking pains not to let the edge hit any part of the plane, then using the clamp as a screwdriver, loosen the cap-screw and slide the cap back along the slot in the cutter, where it can be held fast by a turn of the cap-screw. The edge is now free and can readily be whetted. When the cap needs to be entirely removed, for instance, for grinding, after it has been slid along the cutter slot, as before, it is turned at right angles to the cutter, and then slid down the slot until the cap-screw unbuttons from the cutter. The object in sliding the cap up the slot before turning it, is to prevent the danger of in¬ juring the edge. Some caps are now made with the buttonhole at the upper end of the slot. After sharpening, (see under sharpening, p. 117,) the order is re¬ versed for replacing the cutter. The cap is set at right angles to the cutter, the cap-screw dropped into the slot, the cap is slid up the slot, and turned into line with the cutter, and then slid down the slot till the edge of the cap comes quite near the edge of the cutter. Then the two are held firmly together with the left hand until the cap screw is turned tight. In replacing the cutter and cap in the plane, care should be taken not to injure the edge and to see that the Y adjustment lever tits WOOD HAND TOOLS. 77 into the little slot in the cap; then finally the lever is thrown down tight. Then, by turning the plane sole upward and glancing down it, the proper adjustments with the brass set-screw and lateral ad¬ justment lever are made. When the plane is not being used, it should rest either on a pillow (a little strip of wood in the bench trough), or on its side.* In no case should it be droppd sole down flat on the bench. The block- plane , Fig. 108, gets its name from the fact that it was first made for plan¬ ing off the ends of clap-boards, a process called “blocking in”. The names of the parts of the Bailey block-plane are': 1. Cutter or .bit or plane-iron. 2. Clamp or lever cap. 3. Cap-screw. 4. Adjusting lever. 5. Adjusting nut. 6. Lateral adjustment. 7. Bottom. 8. Mouth piece. 9. Eccentric plate. 10. Knob. The block-plane was devised for use with one hand, as when it is used by carpenters in planing pieces not readily taken to a vise or in planing with a bench-hook. Hence it is made small, 3J4" to 8" long, the clamp is rounded so as to act as a handle, and the cutter is low¬ ered to an angle of about 20° to make the plane easy to grasp. The lower angle of the cutter makes it necessary that the bevel be on the upper side. Otherwise, to give clearance, the bevel would have to be made so long and so thin as to be weak. By putting the bevel up, the angle between the wood and the cutter is maintained practically *See Fig. 206, p. 113. 6 See foot-note p. 70. 78 HANDWORK IN WOOD. as in the smooth-plane. Since the block-plane is intended chiefly for use on end grain, no cap is needed to break the shavings. The ad¬ justable throat makes it possible to cut a very fine shaving. To facili¬ tate the cutting action, several forms of block-planes with a very low angle are now made. Where both hands are free to hold the plane, the block-plane has no advantage over a smooth-plane, even on end grain. Moreover, the cutter cannot be held so firmly in place as that of a smooth-plane, so that it requires constant adjustment. Hence it is not an easy tool for amateurs to handle. There is considerable lost motion in the adjusting nut, and the set-screw, which acts as a knob, is likely to work loose and be lost. It is hardly to be recommended as a part of the equipment of the individual bench in school shops. The piece to be planed with the block-plane may be held either in the vise, end up, or on a bench-hook, Tig. 109. In end planing in the vise, in order to avoid splintering the precaution should be taktn to trim off a corner on the undressed edge, as directed on page 73, or else the planing must be done from both edges toward the center. The sliding cut is much easier than the straight cut, and hence there is a constant temptation to turn the plane at an angle perhaps at an expense of the flat surface desired. In using the bench-hook the piece to be block-planed is placed with the working edge against the block, with the end to be planed to the right and flush with the edge of the bench-hook, in which posi¬ tion it is held with the left hand. The block-plane, held in the right hand, is placed on its side on the bench facing toward the work. In planing, the left hand holds the work firmly against the block of the bench-hook, pressing it somewhat to the right against the plane. The right hand holds the side of the plane flat on the bench and presses it to the left against the bench-hook and work. Held in this position the plane is pushed forward and back until the end is smoothed. Considerable practice is necessary to handle the block-plane well. The scrub-plane is a short plane in which the crown of the cutter, Fig. 110, is quite curved. It is used to reduce surfaces rapidly. Fig - . 100. Using the Block-Plane and Bench-Hook. WOOD HAND TOOLS. 79 The scratcli-planc, Fig. Ill, has a toothed cutter which scratches fine lines along its course. It is used to roughen surfaces of hard wood which are to be glued together, for otherwise the glue would not adhere well. Some tropical woods are so hard that their surfaces can be reduced only by a scratch-plane. It is also useful in preparing the surface of a very cross-grained piece of wood which cannot be planed without chipping. By first scratching it carefully in all di¬ rections, it can then be scraped smooth. It is also called a scraper- plane, because accompanying the plane is a scraper which can be in¬ serted in the same stock and inclined at any required angle. This plane-stock prevents the scraper from unduly lowering some portions of the surface. See also veneer-scraper, p. 91. The rabbeting- or rebating-plane, Fig. 112, is designed for use in cutting out a rectangular recess, such as the rabbet on the back of picture-frames. In line with the right hand corner of the cutter is a removable spur to score the wood so that the shaving which fol- HANDWORK IN WOOD. 80 lows may be cut out clean and not tom out. With the addition of a guiding fence it is called a filletster. This may be used on either the right or left side. In the form shown in Fig. 112, there is also a depth gage. In using this plane see that the corner of the cutter is in line with the sole, and that both it and the spur are sharp. Set the fence and the stop at the desired width and depth of the rabbet. At the first stroke the spur will score the width. This and every stroke should be taken as evenly and carefully as if it were the only one. In the effort to keep the fence pressed close to the side of the wood, the tendency is to tilt the plane over. This causes the very opposite effect from that desired, for the spur runs off diagonally, as in Fig. 114. If this happens stop planing at once, clean out the recess properly with a chisel and then proceed. The dado-plane is much like the rabbeting-plane, ex¬ cept that it is provided with two spurs, one at each side of the cutting edge, to score the wood before cutting. The molding-plane, Fig. 113, as it name indicates, is for making moldings of various forms; as, quarter-round, half-round, ogee, etc. The tonguin g-and-grooving- plane. Fig. 115, is for matching boards, i. e., making a tongue in one to fit into a groove in an¬ other. See Fig. 269, No. 72, p. 182. The circular-plane, Fig. 116, has a flexible steel face which can be adjusted to any required arc, convex or concave, so that curved surfaces may be planed. Fig'. 115. Tonguing-and-Grooving-Plane. Fig. 114. Result of Careless Use of Rabbet-Plane. Fig. 116. Circular-Plane. WOOD HAND TOOLS. 81 The universal plane, Fig. 117, is a combination of various mold¬ ing-, rabbeting-, matching- and other planes. It is capable of many adjustments and applications. The principal parts of this plane are: a main stock, A, with two sets of transverse sliding arms, a depth- gage, F , adjusted by a screw, and a slitting cutter with stop, a sliding section, B, with a vertically adjustable bottom, the auxiliary center bottom, C, to be placed when needed in front of the cutter as an extra Fig. 117. Universal Plane. support or stop. This bottom is adjustable both vertically and lat¬ erally. Fences, D and E. For fine work, fence D has a lateral ad¬ justment by means of a thumb-screw. The fences can be used on either side of the plane, and the rosewood guides can be tilted to any desired angle up to 45°, by loosening the screws on the face. Fence E can be reversed for center-beading wide boards. For work thinner than the depth of the fence, the work may overhang the edge of the bench and fence E be removed. An adjustable stop, to be used in beading the edges of matched boards, is inserted on the left side of the sliding section B. A great variety of cutters are supplied, such as: molding, matching, sash, beading, reeding, fluting, hollow, round, plow, rabbet, and filletster. Special shapes can be obtained by order. The Use of the Universal Plane. Insert the proper cutter, adjust¬ ing it so that the portion of it in line with the main stock, A, will project below the sole the proper distance for cutting. HANDWORK IN WOOD. 82 Adjust the bottom of the sliding section, B, so that the lowest portion of the cutter will project the proper distance below it for cut¬ ting. Tighten the check nuts on the transverse arms and then tighten the thumb-screws which secure the sliding section to the arms. The sliding section is not always necessary, as in a narrow rabbet or bead. When an additional support is needed for the cutter, the auxiliary center bottom, G, may be adjusted in front of it. This may also be used as a stop. Adjust one or both of the fences, D and E, and fasten with the thumb-screws. Adjust the depth-gage, F, at the proper depth. For a dado remove the fences and set the spurs parallel with the edges of the cutter. Insert the long adjustable stop on the left hand of the sliding section. For slitting, insert the cutter and stop on the right side of the main stock and use either fence for a guide. For a chamfer, insert the desired cutter, and tilt the rosewood guides on the fences to the required angle. For chamfer heading use in the same manner, and gradually feed the cutter down by means of the adjusting thumb-nut. There are also a number of planelike tools such as the follow¬ ing: The spokeshave, Fig. 118, works on the same principle as a plane, except that the guiding sur¬ face is very short. This adapts it to work with curved outlines. Tt is a sort of regulated draw-shave. It is sometimes made of iron with an adjustable mouth, which is a convenient form for beginners to use, and is easy to sharpen. The pattern-maker’s spokeshave, Fig. 119, which has a wooden frame, is better suited to more careful work. The method of using the spokeshave is shown in Fig. 120. (See p. 100.) --N —il n -SgT - '] 1 Fig-. 118. Iron Spokeshave. Fig-. 119. Pattern-maker’s Spokeshave. WOOD HAND TOOLS. 83 The router-plane, Figs. 121 and 122, is used to lower a certain part of a surface and yet keep it parallel with the surrounding part, and it is particularly useful in cutting panels, dadoes, and grooves. The cut¬ ter has to be adjusted for each success¬ ive cut. Where there are a number of dadoes to be cut of the same depth, it is wise not to finish them one at a time, but to carry on the cutting of all together, lowering the cutter after each round. In this way all the dadoes will be finished at exactly the same depth. The dowel-pointer. Fig. 123, is a convenient tool for removing the sharp edges from the ends of dowel pins. It is held in a brace. The cutter is adjustable and is removable for sharpening. The cornering tool , Fig. 124, is a simple device for rounding- sharp corners. A cut¬ ter at each end cuts both ways so that it can be used with the grain without chang¬ ing the position of the work. The depth of the cut is fixed. 2. BORING TOOLS. Some boring tools, like awls, force the material apart, and some, like augers, remove material. The brad-awl. Fig, 125, is wedge-shaped, and hence care needs to be taken in using it to keep the edge across the grain so as to avoid splitting the wood, especially thin wood. The size is indicated by the length of the blade when new,—a stupid method. The awl is useful for making small holes in soft wood, and it can readily be sharpened by grinding. ,n-r=E=3» — 1 '*»**”-. - . Fig. 123 Fig. 124 Dowel- Cornering- Tool. Pointer. Fig-. 121. Router-Plane. 84 HANDWORK IN WOOD. 125 12b 127 128 129 130 Fig-. 125. Brad-Awl. Fig. 126. Twist-Drill. Fig. 127. Twist-Bit. Fig. 128. German Gimlet- Bit. Fig - . 129. Bit-Point Drill. Fig. 130. Auger-Bit. WOOD HAND TOOLS. 85 Gimlets and drills are alike in that they cut away material, but unlike in that the cutting edge of the gimlet is on the side, while the cutting edge of the drill is on the end. Twist-drills, Fig. 126, are very hard and may be used in drilling metal. They are therefore useful where there is danger of meeting nails, as in repair work. Their sizes are indicated by a special drill gage. Fig. 220, p. 117. Twist-bits, Fig. 127, are like twist-drills except that they are not hard enough to use for metal. Their sizes are indicated on the tang in 32nds of an inch. Both twist-bits and drill-bits have the advan¬ tage over gimlet-bits in that they are less likely to split the wood. Twist-bits and twist-drills are sharpened on a grindstone, care being taken to preserve the original angle of the cutting edge so that the edge will meet the wood and there will be clearance. German gimlet-bits, Fig. 128, have the advantage of centering well. The size is indicated on the tang in 32nds of an inch. They are useful in boring holes for short blunt screws as well as deep holes. They cannot be sharpened readily but are cheap and easily replaced. Bit-point drills, Fig. 129, are useful for accurate work, but are expensive. Auger-bits, Fig. 130, have several important features. The spur centers the bit in its motion, and since it is in the form of a pointed screw draws the auger into the wood. Two sharp nibs on either side score the circle, out of which the lips cut the shavings, which are then carried out of the hole by the main screw of the tool. The size of auger-bits is indicated by a figure on the tang in 16ths of an inch. Thus 9 means a diameter of 9/16". There are three chief precautions to be taken in using auger-bits. (1) One is to bore perpendicularly to the surface. A good way to do this is to lay the work flat, either on the bench or in the vise, and sight first from the front and then from the side of the work, to see that the bit is perpendicular both ways. The test may also be made with the try-square, Fig. 137, or with a plumb-line, either by the worker, or in difficult pieces, by a fellow worker. The sense of per¬ pendicularity, however, should constantly be cultivated. (2) Another precaution is that, in thru boring, the holes should not be bored quite thru from one side, lest the wood be splintered off on the back. When the spur pricks thru, the bit should be removed, the piece turned over, and the boring finished, putting the spur in the hole which is pricked 86 HANDWORK IN WOOD. thru, in boring from the first side. It is seldom necessary to press against the knob of the brace in boring, as the thread on the spur will pull the bit thru, especially in soft wood. Indeed, as the bit reaches nearly thru the board, if the knob is gently pulled back, then when the spur pricks thru the bit will be pulled out of its hole. This avoids the necessity of constantly watching the back of the board to see if the spur is thru. (3) In stop boring, as in boring for dowels or in making a blind mortise, care should be taken not to bore thru the piece. For this purpose an auger- bit-gage, Fig. 219, p. 116, may be used, or a block of wood of the proper length thru which a hole has been bored, may be slipped over the bit, or the length of bit may be noted before boring, and then the length of the projecting por¬ tion deducted, or the number of turns needed to reach the required depth may be counted on a trial piece. Tying a Fig. 137. Using a Try-Square as . a Guide iu Boring. string around a bit, or making a chalk mark on it is folly. Auger-bits are sharpened with an auger-bit file, Fig. 142, p. 90, a small flat file with two narrow safe edges at one end and two wide safe edges at the other. The “nibs” should be filed on the inside of the bit. The cutting lip should be sharpened from the upper side, that is, the side toward the shank. If sharpened from the side to¬ ward the spur, the necessary clearance is likely to be lost. The plug-cutter. Fig. 131, is useful for cutting plugs with which to cover the heads of screws that are deeply countersunk. Center-bits, Fig. 132, work on the same principle as auger-bits, except that the spurs have no screw, and hence have to be pushed forcibly into the wood. Sizes are given in 16ths of an inch. They are useful for soft wood, and in boring large holes in thin material which is likely to split. They are sharpened in the same way as auger-bits. WOOD HAND TOOLS. 87 Foerstner bits, Fig. 133, are peculiar in having no spur, but are centered by a sharp edge around the circumference. The size is indi¬ cated on the tang, in 16ths of an inch. They are useful in boring into end grain, and in boring part way into wood so thin that a spur would pierce thru. They can be sharpened only with special appli¬ ances. Ex-pansive-bits, Fig. 134, are so made as to bore holes of different sizes by adjusting the movable nib and cutter. There are two sizes, the small one with two cutters, boring from to V/i" and the large one with three cutters boring from J4" to 4". They are very useful on particular occasions, but have to be used with care. Reamers, Fig. 135, are used for enlarging holes already made. They are made square, half-round and six cornered in shape. Countersinks, Fig. 136, are reamers in the shape of a flat cone, and are used to make holes countersink is the most satisfactory form. The washer-cutter, Fig. 138, is useful not only for cutting out washers but also for cutting holes in thin wood. The size is ad¬ justable. 3. CHOPPING TOOLS. The primitive celt, which was hardly more than a wedge, has been differentiated into three modern hand tools, the chisel, see above, p. 53, the ax. Fig. 139, and the adze, Fig. 141. The ax has also been differentiated into the hatchet, with a short handle, for use with one hand, while the ax-handle is long, for use with two hands. Its shape is an adaption to its manner of use. It is oval in order to be strongest in the direction of the blow and also in order that the axman may feel and guide the direction of the blade. The curve at the end is to avoid the awkward raising of the left hand at the moment of striking the blow, and the knob keeps it from slipping thru the hand. In both ax and hatchet there is a two- beveled edge. This is for the sake of facility in cutting into the wood at any angle. Fig-. 138. Washer-Cutter. for the heads of screws. The rose 88 HANDWORK IN WOOD. There are two principal forms, the common ax and the two bitted ax, the latter used chiefly in lumbering, Fig. 4, p. 10. There is also a wedge-shaped ax for splitting wood. As among all tools, there is among axes a great variety for special uses. The hatchet has, beside the cutting edge, a head for driving nails, and a notch for drawing them, thus combining three tools in one. The shingling hatchet, Fig. 140, is a type of this. The adze, the carpenter’s house adze, Fig. 141, is fiat on the lower side, since its use is for straightening surfaces. WOOD HAND TOOLS. 89 References:* WOOD HAND TOOLS. (1) Cutting. Goss, p. 22. Smith, R. H., pp. 1-8. Chisel. Barnard, pp. 59-73. Selden, pp. 44-50, 145-147. Barter, pp. 93-96. Griffith, pp. 53-64. Goss, pp. 20-26. Sickels, pp. 64-67. Wheeler, 357, 421, 442. Knife. Barnard, pp. 48-58. Selden, pp. 26-28, 158. Saw. Griffith, pp. 20-27. Barnard, pp. 114-124. Selden, pp. 41-43, 179-182. Wheeler, pp. 466-473. Hammacher, pp. 309-366. Goss, pp. 26-41. Sickels, pp. 76-79, 84. Smith, R. H., 43-55. Disston, pp. 129-138. Plane. Barnard, pp. 74-80. Selden, pp. 11-26, 165-175. Sickels pp. 72-75, 116. Wheeler, pp. 445-458. Hammacher, pp. 377-400. Smith, R. H., pp. 16-31. Larsson, p. 19. Goss, pp. 41-52. Barter, pp. 96-109. Griffith, pp. 28-45. (2) Boring Tools. Barnard, pp. 125-135. Goss, pp. 53-59. Griffith, pp. 47-52. (3) Chopping Tools. Barnard, pp. 80-88. Selden, pp. 38-40, 141-144. Wheeler, pp. 353-356. *For general bibliography see p. 4. Chapter IV, Continued. WOOD HAND TOOLS. 4. SCRAPING TOOLS. Scraping tools are of such nature that they can only abrade or smooth surfaces. Files, Figs. 142-146, are formed with a series of cutting edges or teeth. These teeth are cut when the metal is soft and cold and then the Fig - . 142. Auger-Bit-File. Fig. 143. Single-Cut Blunt, Flat, Bastard File. Fig. 144. Three-Square Single-Cut File. Fig. 145. Open Cut, Taper, Half-Round File. Fig. 146. Double-Cut File. Fig. 147. Cabinet Wood-Rasp. Fig. 148. File-Card. tool is hardened. There are in use at least three thousand varieties of files, each of which is adapted to its particular purpose. Lengths are measured from point to heel exclusive of the tang. They are classified: (1) according to their outlines into blunt, (i. e., having a uniform cross-section thruout), and taper; (2) according to the shape of their 90 WOOD HAND TOOLS. 91 cross-section, into flat, square, three-square or triangular, knife, round or rat-tail, half-round, etc.; (3) according to the manner of their serrations, into single cut or “float” (having single, unbroken, paral¬ lel, chisel cuts across the surface), double-cut, (having two sets of chisel cuts crossing each 'other obliquely,) open cut, (having series of parallel cuts, slightly staggered,) and safe edge, (or side,) having one or more uncut surfaces; and (4) according to the fineness of the cut, as rough, bas¬ tard, second cut, smooth, and dead smooth. The “mill file,” a very com¬ mon form, is a flat, tapered, single¬ cut file. Fig-. 149. a. Diagram of a Rasp Tooth. b. Cross-Section of a Single-Cut File. Rasps, Fig. 147, differ from files in that instead of having cutting teeth made by lines, coarse projections are made by making indenta¬ tions with a triangular point when the iron is soft. The difference between files and rasps is clearly shown in Fig. 149. It is a good rule that files and rasps are to be used on wood only as a last resort, when no cutting tool will serve. Great care must be taken to file flat, not letting the tool rock. It is better to file only on the forward stroke, for that is the way the teeth are made to cut, and a flatter surface is more likely to be obtained. Both files and rasps can be cleaned with a f -- file-card, Fig. 148. They are sometimes sharp¬ ened with a sandblast, but ordinarily when dull are discarded. Scrapers are thin, flat pieces of steel. They may be rectangular, or some of the edges ma 3 r be curved. For scraping hollow surfaces curved Fig. ISO. Molding-Scrapers. scrapers of various shapes are necessary. Con- Moiding-Scrapers. venient shapes are shown in Fig. 150. The cut¬ ting power of scrapers depends upon the delicate burr or feather along their edges. When properly sharpened they take off not dust but fine shavings. Scrapers are particularly useful in smoothing cross-grained pieces of wood, and in cleaning off glue, old varnish, etc. There are various devices for holding scrapers in frames or han¬ dles, such as the scraper-plane, Fig. Ill, p. 79, the veneer-scraper, and box-scrapers. The veneer-scraper, Fig. 151, has the advantage that the blade may be sprung to a slight curve by a thumb-screw in HANDWORK IN WOOD. 92 ^Fig - . 151. Using- a Veneer- Scraper. the middle of the back, just as an ordinary scraper is when held in the hands. In use, Fig. 152, the scraper may be either pushed or pulled. When pushed, the scraper is held firmly in both hands, the fingers on the forward and the thumbs on the back side. It is tilted forward, away from the opera¬ tor, far enough so that it will not chatter and is bowed back slightly, by pressure of the thumbs, so that there is no risk of the corners digging in. When pulled the position is reversed. One method of sharpening the scraper is as follows: the scraper is first brought to the desired shape, straight or curved. This may be done either by grinding on the grindstone or by filing with a smooth, flat file, the scraper, while held in a vise. The edge is then carefully draw-filed, i. e., the file, a smooth one, is held (one hand at each end) directly at right angles to the edge of the scraper. Fig. 153, and moved sidewise from end to end of the scraper, until the edge is quite square with the sides. Then the scraper is laid flat on the oilstone and rubbed, first on one side and then on the other, till the sides are bright and smooth along the edge, Fig. 154. Then it is set on edge on the stone and rubbed till there are two sharp square corners all along the edge, Fig. 155. Then it is put in the vise again and by means of a burnisher, or scraper steel, both of these corners are carefully turned or bent over so as to form a fine burr. This is done by tipping the scraper steel at a slight angle with the edge and rubbing it firmly along the sharp corner, Fig. 156. To resharpen the scraper it is not necessary to file it afresh every time, but only to flatten out the edges and turn them again with Fig-. 152. Using a Cabinet- Scraper. WOOD HAND TOOLS. 93 slightly more bevel. Instead of using the oilstone an easier, tho less perfect, way to flatten out the burr on the edges is to lay the scraper flat on the bench near the edge. The scraper steel is then passed rap¬ idly to and fro on the flat side of the scraper, Fig. 157. Af¬ ter that the edge should be turned as before. Sandpaper. The “sand” is crushed quartz and is very hard and sharp. Other materials on paper or cloth are also used, as garnet, carborundum, emery, and so on. Sandpaper comes in various grades of coarse¬ ness from No. 00 (the finest) to No. 3, indicated on the back of each sheet. For ordinary purposes No. 00 and No. 1 are sufficient. Sandpaper sheets may readily be torn by placing the sanded side down, one-half of the sheet project¬ ing over the square edge of the bench. With a quick downward mo¬ tion the projecting portion easily parts. Or it may be torn straight by laying the sandpa¬ per on a bench, sand side down, holding the teeth of a back- saw along the line to be torn. In this case, the smooth surface of the sandpaper would be against the saw. Sandpaper should never be used to scrape and scrub work into shape, but only to obtain an extra smoothness. Nor ordinarily should it be used on a piece of wood until all the work with cutting tools is done, for the fine particles of sand remaining in the wood dull the edge of the tool. Sometimes in a piece of cross- grained wood rough places will be discovered by sandpapering. The surface should then be wiped free of sand and scraped before using a cutting tool Fig. 155. Sharpening a Cabinet-Scraper: 3rd Step, Removing - the Wire-Edge. Fig - . 154. Sharpening - a Cabinet-Scraper: 2nd Step, Whetting. Fig. 153. Sharpening a Cabinet-Scraper: 1st Step, Drawfiling. 94 HANDWORK IN WOOD. again. In order to avoid cross scratches, work should be “sanded” with the grain, even if this takes much trouble. For flat surfaces, and to touch off edges, it is best to wrap the sandpaper over a rec¬ tangular block of wood, of which the corners are slightly rounded, or it may be fitted over special shapes of wood for specially shaped surfaces. The objec¬ tion to using the thumb or fingers instead of a block, is that the soft portions of the wood are cut down faster than the hard portions, whereas the use of a block tends to keep the surface even. Steel wool is made by turn¬ ing off fine shavings from the edges of a number of thin discs of steel, held together in a lathe. There are various grades of coarseness, from No. 00 to No. 3. Its uses are manifold: as a substitute for sandpaper, especially on curved surfaces, to clean up paint, and to rub down shellac to an “egg-shell” finish. Like sandpaper it should not be used till all the work with cutting tools is done. It can be manipulated until utterly worn out. 5. POUNDING TOOLS. Fig-. 1S6. Sharpening a Cabinet-Scraper: 4th Step, Turning the Edge The hammer consists of two distinct parts, the head and the handle. The head is made of steel, so hard that it will not be in¬ dented by hitting against nails or the butt of nailsets, punches, etc., which are comparatively soft. It can easily be injured tho, by being driven against steel harder than itself. The handle is of hick¬ ory and of an oval shape to prevent its twisting in the hand. Hammers may be classified as follows: (1) hammers for striking blows only; as, the blacksmith’s hammer and the stone-mason’s hammer, and (2) WOOD HAND TOOLS. 95 compound hammers, which consist of two tools combined, the face for striking, and the “peen” which may be a claw, pick, wedge, shovel, chisel, awl or round head for other uses. There are altogether about fifty styles of hammers varying in size from a jeweler’s hammer to a blacksmith’s great straight-handled sledge-hammer, weighing twenty pounds or more. They are named mostly according to their uses; as, the riveting-hammer, Fig. 159, the upholsterer’s hammer, Fig. 160, the veneering-hammer, Fig. 162, etc. Magnetized hammers, Fig. 161, are used in some trades for driving brads and tacks, where it is hard to hold them in place with the fingers. Fig-. 1S8. Claw-Hammer, Fig. 159. Riveting-Hammer. Fig. 160. Upholsterer’s Hammer, Fig. 161. Magnetized Hammer. Fig. 162. Veneering-Hammer. In the “bell-faced” hammer, the face is slightly convex, in order that the last blow in driving nails may set the nail-head below the surface. It is more difficult to strike a square blow with it than with a plain-faced hammer. For ordinary woodwork the plain-faced, that is, flat-faced claw-hammer. Fig. 158, is best. It is commonly used in carpenter work. It is essential that the face of the hammer be kept free from glue in order to avoid its sticking on the nail-head and so bending the 96 HANDWORK IN WOOD. nail. Hammers should be used to hit iron only; for hitting wood, mallets are used. In striking with the hammer, the wrist, the elbow and the shoulder are one or all brought into play, according to the hardness of the blow. The essential precautions are that the handle be grasped .-it the end, that the blow be square and quick, and that the wood be not injured. At the last blow the hammer should not follow the nail, but should be Drought back with a quick rebound. To send the nail below the surface, a nailset is used. (See below.) The claw is for extracting nails. To protect the wood in withdrawing a nail a block may be put under the hammer-head. When a nail is partly drawn, the leverage can be greatly in¬ creased by continuing to block up in this way, Fig. 163. The mallet, Fig. 164, differs from the hammer in having a wooden instead of a steel head. A maul or beetle is a heavy wooden mallet. The effect of the blow of a mallet is quite different from that of a hammer, in that the force is exerted more gradually; whereas the effect of the ham¬ mer blow is direct, immediate, and local, and is taken up at once. But a mallet continues to act after the first impulse, pushing, as it were. This is because of the elasticity of the head. A chisel, therefore, should always be driven with a mallet, for the chisel handle would soon go to pieces under the blows of a hammer, be¬ cause of their suddenness; whereas the mallet blow which is slower will not only drive the blade deeper with the same Fig - . 164. Mallets. WOOD HAND TOOLS. 97 force, but will not injure the handle so rapidly. Mallet-heads are made square, cylindrical, and barrel-shaped. Carver's mallets are often turned from one piece, hammer and head on one axis. Nailsets, Fig. 165, are made with hardened points, but softer butts, so that the hammer will not be injured. They were formerly made square when nail heads were square, but now round ones are common. To obviate slipping, some have “cup points,” that is, with a con¬ cave tip, and some spur points. To keep the nailset in its place on the nail-head it may be held closely against the third finger of the left hand, which rests on the wood close to the nail. When a nailset is lacking, the head of a brad, held nearly flat, may be used, ing the wood. Fig - . 165. Using a Nailset But care is necessary to avoid bruis- 6. HOLDING TOOLS. A. Tools for Holding Work. The advance in ease of handworking may largely be measured by the facilities for holding materials or other tools. The primitive man used no devices for holding except his hands and feet. The Japanese, who perhaps are the most skilful of joiners, still largely use their fingers and toes. On the other hand, Anglo-Saxons have developed an enormous variety of methods for holding work and tools. Benches. The essential features of a work-bench are a firm, steady table with a vise and places for tools. The joints are either pinned or wedged mortise-and-tenon, or draw-bolt joints. The best benches are made of maple, the tops being strips joined or tongued-and- grooved together. It is common also to have a trough at the back of the top of the bench, i. e., a space 6" or 8" wide, set lower than the upper surface, in which tools may be placed so as not to roll off. A low pillow, fastened at the left hand end of the trough, on which to set planes in order that the edge of the cutter may not be injured, is an advantage. The tool-rack is of capital importance. It has HANDWORK IN WOOD. 98 Fig-. 167. Woodworking - Bench Used at Pratt Institute, Showing* Self-Adjusting- Uprig-ht Vise. WOOD HAND TOOLS. 99 been common in school benches to affix it to a board, which rises con¬ siderably above the top of the bench, Fig. 169, but a better plan is to have the top of it no higher than the bench-top, Fig. 166. Then the light on the bench is not obscured, and when a flat top is needed for large work it can readily be had by removing the tools. Elabo¬ rate benches with lock draw¬ ers are also much used in the shops of large city schools. Vises for holding wood are a Rapid-Acting vise, of three general styles, (1) those with an upright wooden jaw. Fig. 167, which holds wide pieces of work well. They are now made with an automatic adjusting device by which the jaw and the face of the bench are kept parallel; (2) wooden vises with a hori¬ zontal jaw, guided by parallel runners, Fig. 166, and, (3) metal rapid-acting vises, Fig. 168. The latter are the most durable and in Fig. 169. Holding a Large Board in Vise for Planing. most respects more convenient. Special vises are also made for wood- carvers, for saw-filing, etc. The best woodworking benches are equipped with both side- and tail-vises. The tail-vise is supplemented by movable bench-stops for 100 HANDWORK IN WOOD. holding pieces of dliferent lengths. In planing the side of a board it is held in place between the tail-vise and one of the bench-stops. A board should not be squeezed sidewise between the jaws of a vise when it is to be planed, lest it be bent out of shape. In plan¬ ing the edge of a board it is ordinarily held in the side- vise. A long board, one end of which is in the vise, may also need to be supported at the other end. This may be done by clamping to it a hand- screw, the jaw of which rests on the top of the bench, Fig. 169. When the vise is likely to be twisted out of square by the insertion of a piece of wood at one end of it, it is well to insert another piece of equal thickness at the other end of the vise to keep it square, as in Fig. 120, p. 82. In this case, (Fig. 120,) the extra piece also supports the piece being worked upon. The vise is also of great use in carrying on many other processes, but a good workman does not use it to the exclusion of the saw-horse and bench-hook. Horses are of great use both for the rough sawing of material and in supporting large pieces during the process of construction. The common form is shown in Fig. 170, but a more convenient form for sawing has an open top, as in Fig. 171. The picture-frame-vise, Fig. 172, is a very convenient tool for making mitered joints, as in picture-frames. The vise holds two sides firmly so that after gluing they may be either nailed together or a spline inserted in a saw cut previously made. See Fig. 268, WOOD HAND TOOLS. 101 Fiar. 172. Picture-Frame-Vise. No. 55, p. 181. If the last joint in a picture-frame does not quite match, a kerf may be sawn at the junction of the two pieces, which can then be drawn close together. Handscrews, Fig. 173, consist of four parts, the shoulder jaw and the screw jaw, made of maple, and the end spindle and the middle spindle, made of hick¬ ory. The parts when broken, can be bought separately. Handscrews vary in size from those with jaws four inches long to those with jaws twenty- two inches long. The best kind are oiled so that glue will not adhere to them. In adjusting the jaws, if the handle of the middle spindle is held in one hand, and the handle of the end spindle in the other hand, and both are revolved together, the jaws may be closed or opened evenly, Fig. 174. In use care must be taken to keep the jaws parallel, in order to obtain the greatest pres¬ sure and to prevent the spindles from being broken. It is always important to have the jaws press on the work evenly. To secure this, the middle spindle should be tightened first, and then the end spindle. Handscrews are convenient for a great variety of uses, as clamping up glued pieces, holding pieces together temporarily for boring, Fig. 247, p. 153, holding work at any desired angle in the vise, as for chamfering or beveling, Fig. 175, etc.* Clamps are made of both wood and iron, the most satis¬ factory for speed, strength, and durability are steel-bar carpenter clamps, Fig. 176. They vary in length from V /2 ft. to 8 ft. The separate parts are the steel bar A, the cast-iron frame B, the tip C -b ig\ 173. Handscrew. See note 1 , p. 121a. 102 HANDWORK IN WOOD. into which fits the screw D, on the other end of which is the crank E, and the slide F with its dog G, which engages in the notches on the bar. Any part, if broken, can be replaced separately. Iron Randscrews, also called C clamps and carriage- makers’ clamps, Fig. 177, are useful in certain kinds of work, as in gluing in special places and in wood-carving. All iron clamps need blocks of soft wood to be placed between them and the finished work. Pincli-dogs, Fig. 178, are a convenient device for drawing together two pieces of wood, when injury to the surfaces in which they are driven does not matter. They vary in size from $4" to 2j4”- For ordinary purposes the smallest size is sufficient. For especially fine work, double-pointed tacks, properly filed, are con¬ venient. The bench-hook, Fig-. 174. Adjusting Handscrew. device firmly work being etc. for small when sawn, It also a simple holding pieces of they are chiseled, saves the being bench from marred. The angles should be kept exactly square. The miter-box, Fig. 180, is a similar device with the addition of a guide for the saw. The iron miter-box, Fig. 181, Fig. 175. Using - a Handscrew to Hold a Board at an Angle. WOOD HAND TOOLS. 103 with the saw adjustable to various angles, insures accurate work. Such tools as pliers, Fig. 182, pincers, Fig. 183, and nippers, Fig-, 176. Steel-Bar Carpenter’s Clamp, a. Steel Bar. b. Frame, c. Tip. d. Screw, e. Crank, f. Slide. g. Dog-. Fig. 184, made for gripping iron, are often useful in the woodwork¬ ing shop. So are various sorts of wrenches; as fixed, socketed, ad¬ justable, monkey- and pipe-wrenches. B. Tools for holding other tools. The brace or bit-stock, Fig. 185, holds all sorts of boring tools as well as screwdrivers, dowel-pointers, etc. The simple brace or bit-stock consists of a chuck, a handle, and a knob, and is suf¬ ficient for ordinary use; but the ratchet-brace enables the user to bore near to surfaces or corners where a complete sweep cannot be made. It is also useful where sufficient power can be applied only at one part of the sweep. By means of pawls which engage in the ratchet-wheel, the bit can be turned in either direc¬ tion at the will of the user. The size of the brace is indicated by the “sweep,” that is, the diameter of the circle thru which the swinging handle turns. To insert a bit or other tool, Fig. 186, grasp firmly with one hand the sleeve of the chuck pointing it upv/ard, and revolve the handle with the other hand, unscrewing the ri Fig 1 .177. • Iron Handscrew, (Carriage- Maker’s Clamp). Fig. 178. Pinch-Dog. 104 HANDWORK IN WOOD. sleeve until the jaws open enough to admit the whole tang of the bit. Then reverse the motion and the bit will be held tightly in place. Various hand-, breast-, bench-, bow-drills and automatic drills are of use in doing quick work and for boring small holes, Fig. 187. The screwdriver, Fig. 188, is a sort of holding tool for turning, and so driv¬ ing screws. Various devices have been tried to prevent the twisting in the handle. This is now practically assured in various makes. The other important matter in a screwdriver is that the point be of the right temper, so as neither to bend nor to break. If the corners break they can be re¬ ground, but care should be taken not to make the angle too obtuse or the driver will slip out of the slot in the screw-head. The bevel should have a long taper. A shop should be equipped with different sizes of screwdrivers to fit the different sizes of screws. Screwdrivers vary in size, the shank ranging in length from 2 ^ 2 ” to 18”. A long screwdriver is more pow¬ erful than a short one, for the Fig - . 181. Iron Miter-Box. WOOD HAND TOOLS. 105 screwdriver is rarely exactly in line with the axis of the screw, but the handle revolves in a circle. This means an increased leverage, so that the longer the screwdriver, the greater the leverage. For heavy work, screwdriver-bits, Fig. 189, in a bit-stock are use¬ ful, and for quick work, the spiral screwdriver, Fig. 190, and for small work, the ratchet-screwdriver. 7. MEASURING AND MARKING TOOLS. It is a long step from the time when one inch meant the width of the thumb, and one foot meant the length of the foot, to the meas¬ uring of distances and of angles which vary almost infinitesimally. No such accuracy is necessary in measuring wood as in measuring metal, but still there is a considerable variety of tools for this purpose. For measuring distances, the rule, Fig. 191, is the one in most common use. It is usually made of boxwood. For convenience it is hinged so as to fold. A rule is called “two-fold” when it is made of two pieces, “four-fold” when made of four pieces, etc. When measuring or marking from it, it can be used more accurately by turning it on edge, so that the lines of the gradu- Fig. 186 . Inserting' a Bit in Stock. ati ° nS ^ C0Tlle Erectly against the 106 HANDWORK IN WOOD. Fig. 188. Screwdriver. Fig. 18 r >. Screwdriver-Bit. Fig. 110. Spiral Screwdriver. Fig. Id’. Steel Bench-Rule. WOOD HAND TOOLS. 107 Fig-. 193. Back of Steel Square, Brace Measure. work. The one in most com¬ mon use in school shops, is a two-foot, two-fold rule. Some instructors prefer to have pu¬ pils use a four-fold rule, be¬ cause that is the form com¬ monly used in the woodwork¬ ing trades. Steel bench-rules. Fig. 192, are satisfactory in school work because unbreakable and because they do not disappear so rapidly as pocket rules. They need to be burnished occasionally. The steel square, Figs. 193, 194, 196, 197, is useful, not only as a straight-edge and try-square, but also for a number of graduations and tables which are stamped on it. There are various forms, but the one in most common use consists of a blade or “body” 24"x2" and a “tongue,” 16"xlj4", at right angles to each other. Sargent’s trade number for this form is 100. It includes graduations in hundredths, thirty-seconds, sixteenths, twelfths, tenths, and eighths of an inch, also a brace-measure, an eight-square measure, and the Essex board-measure. Another style, instead of an Essex board-measure, and the hun¬ dredths graduation has a rafter-table. The side upon which the name of the maker is stamped, is called the “face,” and the reverse side the “back.” The brace-measure is to be found along the center of the back of the tongue, Fig. 193. It is used thus: the two equal numbers set one above the other rep¬ resent the sides of a square, and the single number to their right, represents in inches and decimals, the diagonal of that square. E. g., 76.37 means that a square the sides of which are 54" would have a diagonal of 76.37". For determining the length of the long side (hy- pothenuse) of a right angle triangle, when the other two given sides are not equal, the foot rule, or an¬ other steel square may be laid diagonally across the 108 HANDWORK IN WOOD. IS m gradua- D'i g. 194. Face of Steel Square. Octagon, “Eight-Square,” Scale. blade and arm, and applied directly to the proper grad¬ uations thereon, and the dis¬ tance between them meas¬ ured on the rule. If the dis¬ tance to be measured feet, use the 1/12 tions on the back of the square. To use the octagonal (or 8-square) scale. Fig. 194, which is along the center of the face of the tongue, with the dividers, take the number of spaces in the sca'e to correspond with the number of inches the piece of wood is square, and lay this distance off from the center point, on each edge of the board. Connect the points thus obtained, diagonally across the corners, and a nearly exact oc¬ tagon will be had. E. g., on a board 12" square, Fig. 195, find A.B.C.D., the centers of each edge. Now with the dividers take 12 spaces from the 8-square scale. Lay off this dis¬ tance on each side as A' A" from A, B' B” from B, etc. Now connect A" with B', B" with C', C" with D', D" with A', and the octagon is obtained. In making a 4V Fig. 195. Method of Using the Eight- Square Scale on the Steel-Square. — _ Co “ square piece of timber octagonal, the same method is used on the butt, sawed true. When the distance from one cen¬ ter is laid off, the marking-gage may be set to the WOOD HAND TOOLS. 109 F TTjTTjTTjTT 11 j 11 rnjTT ll|H ll|T!| nyny 4 3 2 i Fig. 196. Back of Steel Square, Essex Board Measure. distance from the point thus obtained to the corner of the timber, and the piece gaged from all four cor- corners both ways. Cut¬ ting off the outside arrises to the gaged lines leaves an octagonal stick. The board-measure* is stamped on the back of the blade of the square. Fig. 196. The fig¬ ure 12 on the outer edge of the blade is the starting point for all calculations. It repre¬ sents a 1" board, 12" wide, and the smaller fig¬ ures under it indicate the length of boards in feet. Thus a board 12" wide, and 8' long meas¬ ures 8 square feet and so on down the column. To use it, for boards other than 12" wide:— find the length of the board in feet, under the 12" marked on the outer edge of the blade, then run right or left along that line to the width of the board in inches. The number under the width in inches on the line showing the length in feet, gives the board feet for lumber 1" thick. For example, to measure a board 14' long, and 11" wide,—under the figure 12, find 14 (length of the board) ; to the left of this, under 11 is the number 12.10; 12' 10" is the board- measure of the board in question. Since a board 12' long would have as many board feet in it as it is inches wide, the B.M. is omitted for 12' boards. Likewise a board 6' long would have J /z the number of board feet that it is inches wide. If the board is shorter than the lowest figure given (8) it can be found by dividing its doub'e by 2.; e. g., to measure a board 5' long and 9" wide, take 10 under the 12, run to the left of the number under 9, which is 7' 6"; of this would be 3' 9", the number of board feet in the board. * - - to — See page 48. 110 HANDWORK IN WOOD. slLiIiIlLlLj Fig-. 197. Steel Square with Rafter Table. 11 ' total, If the board to be meas¬ ured is longer than any fig¬ ure given, divide the length into two parts and add the result of the two parts ob¬ tained separately. For ex¬ ample, for a board 23' long and 13" wide,—take 12’xl3" = 13'; add to it, ll'xl3"=ll' 24' 11". A good general rule is to think first whether or not the problem can be done in one’s head without the assistance of the square. The table is made, as its name, Board-Meas¬ ure (B.M.) implies, for measuring boards, which are commonly 1" thick. For material more than 1" thick, multiply the B.M. of one surface by the number of inches thick the piece measures. The rafter-table is found on the back of the body of the square. Fig. 197. Auxiliary to it are the twelfth inch graduations, on the outside edges, which may represent either feet or inches. By the “run” of the rafter is meant the hor¬ izontal distance when it is set in place from the TTTTTT 1111111111! 111111 Hill lljll ll|ll H|tt |4 [3 1 2 S H l c z RAFTER6 FEET-INCHES _E Fig-. 198. The “Run” and '■‘■Rise' 1 of a Rafter. end of its foot to a plumb line from the ridge end, i. e., one half the width of the building, Fig. 198. By the “rise” of the rafter is meant the perpendicular distance from the ridge end -AH -SJ i ■jl;' WOOD HAND TOOLS. Ill to the level of the foot of the rafter. By the pitch is meant the ratio of the rise to twice the run, i. e., to the total width of the building. In a Yi pitch, the rise equals the run, or the width of the building; in a 1/3 pitch the rise is 1/3 the width of the Fig. 199. Lumberman’s Board Rule. building; in a 54 pitch the rise is 54 the width of the building. To find the length of a rafter by the use of the table, first find the required pitch, at the left end of the table. Opposite this and under the graduation on the edge representing the run in feet, will be found the length of the rafter; e. g., a rafter having a run of 12' with a J4 pitch, is 13' 5" long, one with a run of 11' and a 1/3 pitch, is 13' 2 t Y, one with a run of 7' and a pitch, is IT 2 T V’ long, etc. When the run is in inches, the readings are for 1/12 of the run in feet; e. g., a rafter with a run of 12" and a yi pitch is 13 T |-'', one with a run of 11" and a 1/3 pitch, is 13 -fy”. Where the run is in both feet and inches, find the feet and the inches separately; and add together; e. g., a rafter with a run of 11' 6", and a Yz pitch, is 15' 6 t V' + 8 T y'=16' 3 T 2 ^".* The lumberman’s board-rule. Fig. 199. To measure wood by it, note the length of the board in feet at the end of the measure. The *See Note 2, p. 121a. HANDWORK IN WOOD. 112 dot nearest the width (measured in inches) gives the B.M. for lum¬ ber 1” thick. The try-square. Fig. 200, which is most commonly used for meas¬ uring the accuracy of right angles, is also convenient for testing the width of a board at various places along its length, for making short meas¬ urements, and as a guide in laying out lines with a pencil or knife at right angles to a surface or edge. It is well to test the try-square for accur¬ acy, by pressing the head against a straight edge, draw¬ ing a fine line along the blade, turning over the try-square and trying the blade along the line just drawn. The sizes are various and are indicated by the length of the blade. A convenient size for the individual bench and for ordinary use has a blade 6" long. It is also well to have in the shop one large one with a 12" blade. In testing the squareness of work with the try-square, care must be taken to see that the head rests firmly against the surface from which the test is made, and then slipped down till the blade touches the edge being tested, Fig 203. The edge should be tested at a number of places in the same way; that is, it should not he slid along the piece. The try-square is also of great use in scribing lines across boards, Fig. 204. A good method is to put the point of the knife at the beginning of the desired line, slide the square along until it touches the knife-blade; then, holding the head of the square firmly against the edge, draw the knife along. WOOD HAND TOOLS. 113 pressing it lightly against the blade, holding it perpendicularly. To prevent the knife from running away from the blade of the try- square, turn its edge slightly towards the blade. The miter-square, Fig. 201, is a try-square fixed at an angle of -15°. The sliding T bevel. Fig. 202, has a blade adjustable to any angle. It may be set either from a sample line, drawn on the wood, from a given line on a protractor, from drawing triangles, from the graduations on a framing square, or in other ways. It is used similarly to the T- square. Winding-sticks, Fig. 205, consist of a pair of straight strips of exactly the same width thruout. They are used to find out whether there is any twist or “wind” in a board. This is done by placing them parallel to each other, one at one end of the board, and the other at the other end. By sighting across them, one can readily see whether the board be twisted or not, Fig. 206. The blades of two framing-squares may be used in the same manner. Compasses or dividers. Fig. 207, consist of two legs turning on a joint, and having sharpened points. A convenient form is the wing divider which can be accurately adjusted by set-screws. A pencil can be substituted for the re¬ movable point. They are used for describing circles and arcs, for spacing, for measuring, for subdividing distances, and for scribing. In scribing a line parallel with a given outline, one leg follows the given edge, or outline, and the point of the other, marks the desired line. Used in this way they are very convenient for marking out chamfers, especially on curved edges, a sharp pencil being substituted for the steel point. Fig-. 205. Winding-Sticks, 12 inches Long. 114 HANDWORK IN WOOD. The beam-compass. Fig. 208, consists of two trammel-points run¬ ning on a beam which may be made of any convenient length. It is used for describing large circles. A pencil may be attached to one point. Calipers, outside and inside, Figs. 209, 210, are necessary for the accurate gaging of diameters, as in wood-turning. Fig - . 207. Winged Dividers. Fig. 208. Beam-Compass or Trammel Points. Fig. 209. Outside Calipers. Fig. 210. Inside Calipers. The marking-gage. Fig. 211, consists of a head or block sliding on a beam or bar, to which it is fixed by means of a set-screw pressing on the gib. On the face of the head is a brass shoe to keep the face from wearing. Projecting thru the beam is a steel spur or point, which should be filed to a flat, sharp edge, a little rounded and sharpened on the edge toward which the gage is to be moved, Fig. 212. It should pro¬ ject about l /$" from the beam. If the spur be at all out of place, as it is likely to be, the graduations on a beam will be unreliable. Hence it is best to neglect them entirely when setting the gage and always to measure with the rule from the head to the spur, Fig. 213. In use the beam should be tilted forward, so as to slide on its corner, Fig. 214. In this way WOOD HAND TOOLS. 115 the depth of the gage line can be regulated. Ordinarily, the finer the line the better. The head must always be kept firmly pressed against the edge of the wood so that the spur will not run or jump Fig-. 213. Setting a Marking-Gage. away from its desired course. Care should also be taken, except in rough pieces, to run gage lines no farther than is necessary for the sake of the appearance of the finished work. To secure accuracy, all gaging on the surface of wood, should be done from the “working face” or “working edge.” It is sometimes advisable, as in laying out chamfers, not to mark their edges with a marking- gage, because the marks will show after the chamfer is planed off. A pencil mark should be made instead. For this purpose a pencil-gage may be made by removing the spur of a marking-gage, and boring in its place a hole to receive a pencil stub with a blunt point, or a small notch may be cut in the back end of the beam, in which a pencil point is held while the gage is worked as usual except that its position is reversed. For work requir- , . Fig. 214. Using the Marking-Gage. mg less care, the pencil may 116 HANDWORK IN WOOD. be held in the manner usual in writing, the middle linger serv¬ ing as a guide, or a pair of pencil compasses may be used, one leg serving as a guide. A special gage is made for gag¬ ing curved lines, Fig. 215. The cutting-gage, Fig. 216, is similar to a marking-gage, except that it has a knife-point inserted instead of a spur. It is very useful in cutting up soft, thin wood even as thick as y!\". The slitting-gage is used in a sim¬ ilar way, but is larger and has a handle. The mortise-gage, Fig. 217, is a marking-gage with two spurs, with which two parallel lines can be drawn at once, as in laying out mortises. One form is made entirely of steel having, instead of spurs, discs with sharp¬ ened edges. The scratch-awl. Fig. 218, has a long, slender point which is useful not only for marking lines, but for centering. The auger-hit-gage, Fig. 219, is a convenient tool for measuring the depth of holes bored, but for ordinary pur¬ poses a block of wood sawn to the proper length thru which a hole is bored, is a satisfactory substitute. Screw- and wire-gages, Fig. 220, are useful in measuring the lengths and sizes of screws and wire when fitting or ordering. The spirit-level, and the plumb-line which it has largely replaced, are in constant use in carpentering, but are rarely needed in shopwork. ._/vw» i li lifili lililiklllilililili _ Fig - . 217. Roller Mortise-Gage. Fig. 218. Scratcli-Awl. Fig. 21 f >. Auger-Bit-Gage WOOD HAND TOOLS. 117 Blackboard compasses, triangles, etc., are convenient accessories in a woodworking classroom. 8. SHARPENING TOOLS. The grindstone for woodworking tools is best when rather fine and soft. The grinding surface should be straight and never concave. The stone should run as true as possible. It can be made true by a b c Fig-. 220. Screw- and Wire-Gages. a. Screw-Gage. b. Wire-Gage. c. Twist-Drill-Gage. using a piece of 1" gas pipe as a truing tool held against the stone when run dry. Power grindstones usually have truing devices attached to them, Fig. 221. A common form is a hardened steel screw, the thread of which, in working across the face of the grindstone, as they both revolve, shears off the face of the stone. The surface should always be wet when in use both to carry off the particles of stone and steel, and thus preserve the cutting quality of the stone, and to keep the tool cool, as otherwise, its temper would be drawn, which would show by its turning blue. But a grindstone should never stand in water or it would rot. 118 HANDWORK IN WOOD. It is well to have the waste from the grindstone empty into a cisternlike hox under it, Fig. 221. In this box the sediment will settle while the water overflows from it into the drain. Without such a box, the sediment will be carried into and may clog the drain. The hox is to be emptied occasionally, before the sediment overflows. Fig-. 221. Power Grindstone. In order that the tool may be ground accurately, there are vari¬ ous devices for holding it firmly and steadily against the stone. A good one is shown in Figs. 221 and 222. This device is constructed as follows: A board A is made 2" thick, 6" wide, and long enough when in position to reach from the floor to a point above the level of the top of the stone. It is beveled at the lower end so as to rest snugly against a cleat nailed down at the proper place on the floor. The board is held in place by a loop of iron, B, which hooks into the holes in the trough of the grindstone. In the board a series of holes (say 1" in diameter) are bored. These run parallel to the floor when the board is in place, and receive the end of the tool- WOOD HAND TOOLS. 119 holder. The tool-holder consists of four parts: (1) a strip C, V/z" thick, and as wide as the widest plane-bit to be ground. The for¬ ward end is beveled on one side; the back end is rounded to fit the holes in the main board A. Its length is determined by the distance Fig. 222. Grinding Device. from the edge of the tool being ground to the most convenient hole in A, into which the rear end is to be inserted. It is better to use as high a hole as convenient, so that as the grindstone wears down, Fig. 223. Holder for Grinding Chisels or Plane-Bits. the stick will still be serviceable; (2) a strip, D, of the same width as A and %" thick, and 15" to 18" long; (3) a cleat, E, nailed across D; (4) a rectangular loop of wrought iron or brass, F, HANDWORK IN WOOD. 120 which passes around the farther end of the two strips, 0 and D, and is fastened loosely to D by staples or screws. The tool to be ground slips between this loop and the strip C, and is held firmly in place by the pressure applied to the back end of D, which thus acts as a lever on the fulcrum E. Any desired bevel may be obtained on the tool to be sharpened, by choosing the proper hole in A for the back end of C or by ad¬ justing the tool forward or backward in the clamp. As much pres¬ sure may be put on the tool as the driving belt will stand without slipping off. A still simpler holder for the plane-bit only, is a strip of wood 1 ^ 2 " thick and 2" wide, cut in the shape G shown in Fig. 223. The plane-bit fits into the saw-kerf K, and in grinding is easily held firmly in place by the hand. By inserting the rear end of the stick G into a higher or lower hole in the board A, any desired angle may be obtained. G is shown in position in Fig. 221. All such devices necessitate a perfectly true stone. The essential features are, to have a rigid support against which the tool may be pushed by the revolving stone, to hold the tool at a fixed angle which may be adjusted, and to press the tool against the stone with con¬ siderable pressure. The wheel should revolve toward the edge which is being ground, for two rea¬ sons. It is easier to hold the tool steadily thus, and the danger of producing a wire edge is lessened. The edge as it becomes thin, tends to spring away from the stone and this tendency is aggra¬ vated if the stone revolves away from the edge. If the stone does not run true and there is a consequent danger of digging into the stone with the tool which is being sharpened, the stone would better revolve away from the edge. The grinding should continue until the ground surface reaches the cutting edge and there is no bright line left along the edge. If the grinding is continued beyond this point, nothing is gained, and a heavy wire edge will be formed. WOOD HAND TOOLS. 121 A very convenient and inexpensive grinding tool, Fig. 224, sold as the “Agacite grinder has a number of different shaped grinding stones made chiefly of carborundum. Others on the market have the additional advantage that the gears are all safely enclosed; e. g., the Robertson Tool Grinder, Buffalo, H, Y. The oilstone. After grinding, edge tools need whetting. This is done on the whetstone, or oilstone. The best natural stones are found near Hot Springs, Arkansas. The fine white ones are called Arkan¬ sas stones, and the coarser ones Washita stones. The latter are better for ordinary woodworking tools. The India oilstone , an artificial stone, Fig. 77, p. 58, cuts even more quickly than the natural stones. It is made in several grades of coarseness. The medium grade is recommended for ordinary shop use. Oil is used on oilstones for the same pur¬ pose as water on a grindstone. When an oil¬ stone becomes hollow or uneven by use, it may be trued by rubbing it on a flat board covered with sharp sand, or on sandpaper tacked over a block of wood. Slipsiones, Fig. 225, are small oilstones, made into various shapes in order to fit different tools, as gouges, the bits of molding-planes, etc. Fig. 225 Sliretone. Fig, 225 A. Jorgenson Adjustable Handscrews. Files are used for sharpening saws, augers, scrapers, etc. See above, p. 90. 9. CLEANING TOOLS. The bench duster. One may be noted hanging on the bench shown in Fig. 166, p. 98. Bristle brushes for cleaning the benches are essential if the shop is to be kept tidy. 7 Made by the Empire Implement Co., Albany, N. Y 121a HANDWORK IN WOOD. Buffer. Whenever a lathe or other convenient revolving shaft is available, a buffer made of many thicknesses of cotton cloth is very valuable for polishing tools. The addition of a little tripoli greatly facilitates the cleaning. Note 1: — An improved type of 1 able, having steel spindles, which a: jaws can be adjusted to any angle and force. See Fig. 225A. Note 2: — One of the common square is to obtain the two angles— The angles made with the straigl landscrew is the Jorgensen adjust- re practically indestructible. The and position with great rapidity and convenient uses of the steel -other than the right angle—of a right angled triangle, when the ratio of the two legs is known. These are often called the bat¬ ters. This is done bv laying the square on a straight edge in such a way that the distance on the tongue from the heel of the square corresponds to the length of one leg and the distance on the other blade to the other leg. edge are the “batters.” See Fig. 225B. This method is used, for example, in obtaining the cuts of braces and of plain rafters, and in laying out stairs. The angles at the ends of the side rails of a chair (See p. 198) can be obtained by this mean«. WOOD HAND TOOLS. 121b wood hand tools.— Continued. References:* (4) Scraping Tools. Barnard, pp. 130-142. Wheeler, pp. 485, 473. (5) Pounding Tools. Barnard, pp. 24-47. Sickels, p. 70. Wheeler, pp. 414, 428-432. (6) Punching Tools. Barnard, p. 29. Wheeler, p. 433. (7) Gripping Tools. For holding work: Goss, p. 63. Wheeler, pp. 85-75, 475. For holding other tools: Goss, pp. 56-59. (8) Measuring and Marking Tools. Goss, pp. 9-20. Griffith, pp. 9-19. Hodgson, The Sieel Square. Wheeler, p. 465. Tate, pp. 21-25. (9) Sharpening Tools. Barnard, pp. 138-142. Sickels, pp. 80-85. Wheeler, pp. 480-488. Griffith, pp. 71-75. Selden, pp. 149, 177, 182. Hodgson, I, pp. 61-74. Selden, pp. 31, 111, 150. Goss, p. 60. Barter, p. 128. Selden, p. 161. Selden, pp. 140, 147, 186, 194. Hammaeher, pp. 288-291. Selden, p. 143. Building Trades Pocketbook, pp. 234* 237. Selden, pp. 149, 150-152, 175. Sargent’s Steel Squares. Selden, pp. 153, 162, 172, 180. Goss, pp. 39, 64-69. For general bibliography see p. 4. Chapter V. WOOD FASTENINGS. The following are the chief means by which pieces of wood are fastened together: nails, screws, bolts, plates, dowels, glue, hinges, and locks. NAILS Nails, Fig. 226, may be classified according to the material of which they are made; as, steel, iron, copper, and brass. Iron nails may be galvanized to protect them from rust. Copper and brass nails are used where they are subject to much danger of corrosion, as in boats. Nails may also be classified according to the process of manufacture; as, cut nails, wrought nails, and wire nails. Cut nails are cut from a plate of metal in such a way that the width of the nail is equal to the thickness of the plate, and the length of the nail to the width of the plate. In the third dimension, the nail is wedge-shaped, thin at the point and thick at the head. Unless properly driven, such nails are likely to split the wood, but if properly driven they are very firm. In driving, the wedge should spread with and not across the grain. Wrought nails are worked into shape from hot steel, and have little or no temper, so that they can be bent over without breaking, as when clinched. Horseshoe- and trunk-nails are of this sort. They are of the same shape as cut nails. Wire nails are made from drawn steel wire, and are pointed, headed, and roughened by machinery. They are comparatively cheap, hold nearly if not quite as well as cut nails, which they have largely displaced, can be bent without breaking, and can be clinched. Fig-. 226. a. Cut nail, common, b. Flat-head wire nail, No. 1, com¬ mon. c. Finishingnail, or brad. 123 124 HANDWORK IN WOOD. Nails are also classified according to the shape of their heads; as, common or flat-heads, and brads or finishing nails. Flat-heads are used in ordinary work, where the heads are not to be sunk in the wood or “set.” Some nails get their names from their special uses; as, shingle- nails, trunk-nails, boat-nails, lath-nails, picture-nails, barrel-nails, etc. The size of nails is indicated by the length in inches, and by the size of the wire for wire nails. The old nomenclature for cut nails also survives, in which certain numbers are prefixed to “penny.” For example, a threepenny nail is 134 ” long, a fourpenny nail is 1J4" long, a fivepenny nail is 134" long, a sixpenny nail is 2" long. In other words, from threepenny to tenpenny 34" is added for each penny, but a twelvepenny nail is 334" long, a sixteenpenny nail is “iYi" long, a twentypenny nail is 4” long. This is explained as mean¬ ing that “tenpenny” nails, for example, cost tenpence a hundred. Another explanation is that originally 1000 of such nails weighed a pound. The size of cut nails is usually still so indicated. Nails are sold by the pound. The advantages of nails are that they are quickly and easily ap¬ plied, they are strong and cheap, and the work can be separated, tho with difficulty. The disadvantages are the appearance and, in some cases, the insecurity. The holding power of nails may be increased by driving them into the wood at other than a right angle, especially where several nails unite two pieces of wood. By driving some at one inclination and some at another, they bind the pieces of wood together with much greater force than when driven in straight. The term brads was once confined to small fin¬ ishing nails, but is now used for all finishing nails, in distinction from common or flat-headed nails. The heads are made round instead of flat so that they may be set easily with a nailset and the ho'e filled with a plug, or, where the wood is to be painted, with putty. They are used for interior finishing and other nice work. Taclcs, Fig. 227, vary in size and shape according to their use; as, flat-heacled, gimp, round-headed, and double-pointed or matting tacks, a sort of small staple. Their size is indicated by the word “ounce.” For example, a two-ounce tack is 34 " l° n g> a three-ounce Fig. 227. Tack. WOOD FASTENINGS. 125 tack is y%’ long, a four-ounce tack is 7/16" long, a six-ounce tack is y 2 " long, etc. This term once meant the number of ounces of iron required to make 1000 tacks. Tacks are useful only in fastening to wood thin material, such as veneers, textiles, leather, matting, tin, etc. Tinner’s tacks, which are used for clinching, are commonly called clinch-nails. Wire tacks, altho made, are not so successful as cut tacks because they lack a sharp point, which is es¬ sential. Corrugated fasteners. Fig. 228, or fluted nails, are used to fasten together two pieces of wood by driving the fastener so that one- half of it will be on each side of the joint. Their size is indicated by the length and the number of corrugations, as J4", four. They are often useful where nails are impracticable. Glaziers’ points are small, triangular pieces of zinc, used to fasten glass into sashes. SCREWS (a) Wood-screws, Fig. 229, may be classified by the material of which they are made; as, steel or brass. Steel screws may be either bright,—the common finish,—blued by heat or acid to hinder rust¬ ing, tinned, or bronzed. Brass screws are essential wherever rust would be detrimental, as in boats. (b) Screws are also classified by shape; as, flat-headed, round- headed, fillister-headed, oval-countersunk-headed, and square-headed screws. Flat-heads are most commonly used. There are also special shapes for particular purposes. Bound-heads may be used either for decoration or where great drawing power is desirable. In the latter case, washers are commonly inserted under the heads to prevent them from sinking into the wood. Oval-heads are used decoratively, the head filling the countersunk hole, as with flat-heads, and projecting a trifle besides. They are much used in the interior finish of railway cars. They are suitable for the strap hinges of a chest. The thread of the screw begins in a fine point so that it may penetrate tire wood easily where no hole has been bored as is often the case in soft wood. The thread extends about two-thirds the length of the screw. Any longer thread would only weaken the Fig-. 228. Corrugated Fastener. HANDWORK IN WOOD. 126 screw where it most needs strength, near the head, and it does not need friction with the piece thru which it passes. The size of screws is indicated by their length in inches, and by the diameter of the wire from which they are made, using the stand¬ ard screw-gage, Fig. 220, p. 117. They vary in size from No. 0 (less than 1/16") to No. 30 (more than 7/16") in diameter, and in length from %" to 6". The following is a good general rule for the use of screws: make the hole in the piece thru which the screw passes, large enough for the screw to slip thru easily. Countersink this hole enough to allow the head to sink flush with the surface. Make the hole in the piece into which the screw goes small enough for the thread of the screw to catch tight. Then all the strength exerted in driving, goes toward drawing the pieces together, not in overcoming friction. The hole must be deep enough, especially in hard wood and for brass screws, to prevent the possibility of twisting off and breaking the screw. Soap is often useful as a lubricant to facilitate the driving of screws. Where it is desirable that the heads do not show, a hole may first be bored with an auger-bit large enough to receive the head and deep enough to insert a plug of wood, which is cut out with a plug-cutter, Fig. 131, p. 84, and glued in place. If pains are taken to match the grain, the scar thus formed is inconspicuous. In rough work, the screw may be driven into place with a ham¬ mer thru most of its length, and then a few final turns be given with a screwdriver, but this breaks the fibers of the wood and weakens their hold. In “drive-screws,” Fig. 229, e, the slot is not cut all the way across the head, in order that the blows of the hammer may not close the slot. The advantages of screws are, that they are very strong and that the work can easily be taken apart. If they loosen they can be Fig-. 229. a. Flat-head Wood-screw, b. Round-head Wood-screw, c. Fillister- head Wood-screw. d. O val-countersunk- head Wood-screw e. Drive-screw, f. Square- head (lag--or-coach-) Screw. WOOD FASTENINGS. 127 retightened. The disadvantages are, that they are expensive, that they take time to insert, that they show very plainly, and that they do not hold well in end grain. BOLTS Bolts with nuts are useful where great strength is desired. There are three chief varieties, Fig. 230. Stove-bolls are cheaply made (cast) bolts having either flat or round heads with a slot for the screwdriver, like ordinary screws. Carriage-bolts are distinguished by having the part of the shank which is near the head, square. Machine-bolts have square, hexagonal, or button heads. Machine-screws, Fig. 231, are similar to stove-bolts, but are accurately cut and are meas¬ ured with a screw-gage. The varieties are, a, flat-head, b, round-head, c, fillister-head, d, oval- countersunk-head, all with slots for screwdriver. fig-, m a. stove. ’ bolt. b. Carriag-e-bolt. Plates, Fig. 232, include corner-irons, straight c - Machine-bolt, plates and panel-irons. These are made of either iron or brass and are used in fastening legs to the floor, in stiffening joints, affixing tops, etc. Dowel-rods. Dowel-rods are cylindrical rods, from 3/16" to 1" in diameter, and 36", 42", and 48" long. They are commonly made of birch or maple, but maple is more satisfactory as it shrinks less and is stronger than birch. They are made both for snug and loose fit. Dowels are used as pins for joining boards edge to edge, and as a substitute for mortise-and- tenon joints. There is, to be sure, a prej¬ udice against dowels on the part of cabinet-makers due, possibty, to the willingness to have it appear that doweling is a device of inferior me¬ chanics. But doweling is cheaper and quicker than ten- 128 HANDWORK IN WOOD. oiling, and there are many places in wood construction where it is just as satisfactory and, if properly done, just as strong. Certain parts of even the best furniture are so put together. Shoe pegs serve well as small dowels. They are dipped in glue and driven into bracl-awl holes. Wedges are commonly used in door construction between the edges of tenons and the insides of mor¬ tises which are slightly beveled, No. 34, Fig. 266, p. 179. Or the Fig'. 232. a. Corner-iron. b. Straight plate, c. Panel-iron. end of a tenOU may be split to re¬ ceive the wedges, No. 35, Fig. 266. The blind wedge is used in the fox-tail joint, No. 36, Fig. 266. GLUE Glue is an inferior kind of gelatin, and is of two kinds,—animal glue and fish glue. Animal glue is made of bones and trimmings, cuttings and fleshings from hides and skins of animals. Sinews, feet, tails, snouts, ears, and horn pith are also largely used. Cattle, calves, goats, pigs, horses, and rabbits, all yield characteristic glues. The best glue is made from hides of oxen, which are soaked in lime water until fatty or partly decayed matter is eaten out and only the glue is left. The product is cleaned, boiled down and dried. The best and clearest bone glues are obtained by leaching the bones with dilute acid which dissolves out the lime salts and leaves the gelatinous matters. Such leached bone is sold as a glue stock, under the name of “osseine.” This material together with hides, sinews, etc., has the gelatin or glue extracted by boiling again and again, just as soup stock might be boiled several times. Each extrac¬ tion is called a “run.” Sometimes as many as ten or fifteen runs are taken from the same kettle of stock, and each may be finished alone or mixed with other runs from other stock, resulting in a great variety of commercial glues. WOOD FASTENINGS. 129 Manufacturers use many tests for glue, such as the viscosity or running test, the odor, the presence of grease or of foam, rate of set, the melting-point, keeping properties, jelly strength (tested be¬ tween the finger tips), water absorption (some glues absorb only once their weight, others ten or twelve times), and binding or ad¬ hesive tests. This latter varies so much with different materials that what may be good glue for one material is poor for another. Putting all these things together, glues are classified from grade 10 to 160, 10 being the poorest. The higher standards from 60 and upwards are neutral hide glues, clear, clean, free from odor, foam, and grease. The lower standards are chiefly bone glues, used for sizing straw hats, etc. They are rigid as compared with the flexibility of hide glues. For wood joints the grade should be 70 or over. For leather, nothing less than 100 should be used, and special cements are better still. The best glue is transparent, hard in the cake, free from spots, of an amber color, and has little or no smell. A good practical test for glue is to soak it in water till it swells and becomes jelly-like. The more it swells without dissolving the better the quality. Poor glue dissolves. Glue is sometimes bleached, becoming brownish white in color, but it is somewhat weakened thereby. Fish glue is made from the scales and muscular tissue of fish. Isinglass is a sort of glue made from the viscera and air bladder of certain fish, as cod and sturgeon. Liquid glue may be made either from animal or fish glue. The LePage liquid glue is made in Gloucester, Mass., one of the greatest fish markets in the country. Liquid glue is very convenient because always ready, but is not so strong as hot glue, and has an offensive odor. Liquid glues are also made by rendering ordinary glue non¬ gelatinizing, which can be done by several means; as, for instance, by the addition of oxalic, nitric, or hydrochloric acid to the glue so¬ lution. To prepare hot glue, break it into small pieces, soak it in enough cold water to cover it well, until it is soft, say twelve hours, and heat in a glue-pot or double boiler, Fig. 243, p. 148. The fresher the glue is, the better, as too many heatings weaken it. When used it should be thin enough to drip from the brush in a thin stream, so that it will fill the pores of the wood and so get a grip. Two sur¬ faces to be glued together should be as close as possible, not separated 130 handwork; in wood. by a mass of glue. It is essential that the glue be hot and the wood warm, so that the glue may remain as liquid as possible until the surfaces are forced together. Glue holds best on side grain. End grain can be made to stick only by sizing with thin glue to stop the pores. Pieces thus sized and dried can be glued in the ordinary way, but such joints are seldom good. Surfaces of hard wood that are to be glued should first be scratched with a scratch-plane. Fig. Ill, p. 79. To make waterproof glue, add one part of potassium bichromate to fifty parts of glue. It will harden when exposed to the air and light and become insoluble. 8 General directions for gluing Before applying glue to the parts to be fastened together, it is a good plan to assemble them tempo¬ rarily without glue, to see that all the parts fit. When it is desirable that a certain part, as the panel, in panel construction, should not be glued in place, it is a wise precaution to apply wax, soap, or oil to its edges before insertion. Since hot glue sets quickly, it is necessary after the glue is applied to get the parts together as soon as possible. One must learn to work fast but to keep cool. To expedite matters, everything should be quite ready before the process is begun, clamps, protecting blocks of wood, paper to protect the blocks from sticking to the wood, braces to straighten angles, mallet, try-square, and all other appliances likely to be required. Whenever it is possible to break up the process into steps, each step can be taken with more deliberation. For example, in assem¬ bling framed pieces that are doweled, it is well to glue the dowels into one set of holes beforehand, making tenons of them, as it were. Time is thus saved for the final assembling when haste is imperative. The superfluous glue around the dowels should be carefully wiped off. Likewise in gluing up framed pieces, sections may be put together separately; as, the ends of a table, and when they are dry then the whole may be assembled. When the pieces are together the joints should be tested to see that they are true, and that there are no twists. A good way to insure squareness, is to insert a diagonal brace on the inside, corner to corner, as in Fig. 294, p. 195. Such a brace 8 For recipes for this and other glues, see Woodcraft, May ’07, p. 49. • For special directions, for particular joints, see under the various joints (Chap. VII.) WOOD FASTENINGS. 131 should be provided when the trial assembly is made. Another good way to insure squareness is to pass a rope around two diagonally op¬ posite posts, and then by twisting the rope, to draw these corners toward each other until the frame is square. The superfluous glue may be wiped off at once with a warm damp cloth, but not with enough water to wet the wood. Or by waiting a few minutes until the glue thickens, much of it can readily be peeled off with an edge tool. Either of these ways makes the cleaning easier than'to let the superfluous glue harden. The work when glued should remain at least six hours in the clamps to harden. HINGES Hinges, Fig. 233, are made in several forms. The most common are the butt-hinge or butt, the two leaves of which are rectangular, as in a door-hinge; the strap-hinge, the leaves of which are long and strap-shaped; the Tee-hinge, one leaf of which is a butt, and the other strap-shaped; the chest-hinge, one leaf of which is bent at a right angle, used for chest covers; the table-hinge used for folding table tops with a rule joint; the piano-hinge, as long as the joint; the blank hinge or screen-hinge which opens both ways; the stop- hinge, which opens only 90°; and the “hook-and-eye” or “gate” hinge. Fig. 233. a. Butt-hinge, b. Tee-hinge, c Chest-hinge, d. Table-hinge, e. Blank or Screen-hinge. The knuckle of the hinge is the cylindrical part that connects the two leaves, Fig. 234. The “acorn” is the head of the “pintle” or pin that passes thru the knuckle. Sizes of butts are indicated in inches for length, and as “narrow,” “middle,” “broad” and “desk” for width. The pin may be either riveted into the knuckle as in box-hinges or removaVe as in door-butts. Sometimes, as in blind- 132 HANDWORK IN WOOD. Fig-. 234. Parts of a butt-hinge. 1.1. Leaves. 2.2.2. Knuckle. 3. Pintle. 4. Acorn. hinges, the pintle is fastened into one knuckle, but turns freely in the other. A butt-hinge may be set in one of three positions, Fig. 235: (1) Where it is desired to have the hinge open as wide as possible, as in a door. Here the knuckle is set well out from the wood. (2) Where it is desired to have the hinged portion open flat and no more. Here the cen¬ ter of the pin is in line with the out¬ side surface of the wood. This is less likely to rack the hinge than the other two positions. (3) Where it is desired to have the knuckle project as little as possible. HINGING In setting the hinges of a box cover, first see that the cover fits the box ex¬ actly all the way around. In the case of a door, see that it fits its frame, evenly all the way around, but with a little play. To insure a tighter fit at the swinging edge this edge should be slightly beveled inwards. In attaching a butt-hinge, the essential thing is to sink the hinge into the wood, exactly the thickness of the knuckle. The gains may be cut in one or both of the pieces to be hinged together. With these matters determined proceed as follows: In the case of a box cover, the hinges should be set about as far from the ends of the box as the hinge is long. In the case of an upright door, locate the hinges respectively above and below the lower and upper rails of the door. Mark with the knife on the edge of the door the length of the hinge, and square across approximately the width of the gain to receive it. Do this for both hinges. Between these lines gage the proper width of the gains. Set another gage to one-half the thickness of the knuckle and gage on the door face the depth of the gains. Chisel out the gains, set the hinges in place, bore the holes, and drive the screws. Place the door in position again to test the fit. If all is well, mark the position of the hinges on the frame, gage and cut the gains, and fasten in the hinges. Where the hinge is gained its full thickness into the door, WOOD FASTENINGS. 133 no gain, of course, is cut in the frame. If the hinges are set too shallow, it is an easy matter to unscrew one leaf of each and cut a little deeper. If they are set too deep the screws may be loosened and a piece of paper or a shav¬ ing inserted underneath along the outer arris of the gain. LOCKS The chief parts of a lock are: the bolt, its essential fea¬ ture, the selvage, the plate which appears at the edge of the door or drawer, the box, which contains the mechanism, including the tumbler, ward, spring, etc., the key-pin, into or around which the key is in¬ serted, the strike, the plate at¬ tached opposite the selvage, (often left out as in drawer- locks, but essential in hook-bolt locks, and self-locking locks,) and the escutcheon, the plate around the keyhole. Locks may be classified: (1) According to their uses, of which there are two types, (a). Fig. 236, For drawers, cupboards, tills, wardrobes, and doors. In these the bolt simply projects at right angles to the selvage into the strike, and resists pressure sidewise of the lock, (b), Fig. 237, For desks, roll-top desks, chests, boxes and sliding doors. In these, the bolt in¬ cludes a hook device of some kind to resist pressure perpendicular to the selvage. In some locks, the hook or hooks project sidewise from the bolt, in others the bolt engages in hooks or eyes attached to the strike. (2) According to the method of ap¬ plication, as rim locks, which are fas- Fig-. 236. Rim-lock, for Drawer. 1. Bolt. 2. Selvag-e. 3. Box. 4. Key-pin. 134 HANDWORK IN WOOD. tened on the surface, and mortise locks which are mortised into the edge of a door or drawer or box. INSERTING LOCKS To insert a rim-locle, measure the distance from the selvage to the key-pin, locate this as the center of the keyhole, and bore the hole. If the lock has a selvage, gain out the edge of the door or drawer to receive it. If the lock box has to be gained in, do that next, taking care that the bolt has room to slide. Cut the keyhole to the proper shape with a keyhole-saw or small chisel. Fasten the lock in place, and if there is a strike or face-plate, mark its place and mortise it in. To insert a mortise-loch, locate and bore the keyhole, mortise in the box and the selvage, finish the keyhole, fasten in the lock, add the es¬ cutcheon, locate and mortise in the strike, and screw it in place. Fig - . 237. Mortise-lock, for Box. WOOD FASTENINGS. 135 WOOD FASTENINGS .References : Hammaeher & Schlemmer. Catalog No. 151. Nails. Goss, p. 153. Purfield, Wood Craft, 5: 181. Park, pp. 129-135. Tacks. Wheeler, pp. 429-433. Sickels, p. 70. Screws. Goss, p. 155. Wheeler, p. 476. Barter, p. 86. Dowels. Goss, p. 153. Wheeler, p. 374. Wedges. Goss, p. 151. Glue. Goss, p. 156. Rivington, III, p. 432. Barter, p. 82. Standage, Wood Craft, 7: 48. Park, pp. 141-146. Hinges. Sickels, p. 118. Griffith, pp. 75-78. Wood Craft, 5: 103. Wheeler, pp 428-433. Goss, p. 155. Barter, pp. 84-86. Griffith, pp. 78-80. Park, pp. 136-140. Sickels, p. 104. Griffith, p. 92. Sickels, p. 106. Wheeler, pp. 391-396. Alexander, Wood Craft, 5: 168 Griffith, pp. 80-83. Wheeler, p. 402. For general bibliography see p. 4. Chapter VI. EQUIPMENT AND CAPE OF THE SHOP. Tool equipment. The choice of tools'in any particular shop best comes out of long experience. Some teachers prefer to emphasize certain processes or methods, others lay stress on different ones. The following tentative list is suggested for a full elementary school equip¬ ment for twenty-four students. One bench and its tools may be added for the teacher. The prices given are quoted from Discount Sheet No. 1 for Cata¬ logue of Tools, No. 355 issued by Hammacher, Sehlemmer & Co., Fourth Avenue and 13th Street, New York City, dated 1908, and are correct at the present date (1911). Aggregate orders, however, are always subject to special concessions, and it is suggested that be¬ fore ordering the purchaser submit a list of specifications for which special figures will be quoted. There are good benches, vises, and tools of other makes on the market, but those specified below are typical good ones. Following are two equipments for classes of twenty-four pupils, one severely economical to cost approximately $400, and the other more elaborate to cost approximately $750. $400 TOOL EQUIPMENT. INDIVIDUAL TOOLS. 24 Manual Training School Benches, IT. & S. “L,” @ $8.50.$204.00 24 Stanley, Bed-Rock Planes, No. 604, @ $1.70 each. 40.80 24 Disston’s Back-Saws, No. 4, 10", @ 93c each. 22.32 12 Buck Brothers’ Firmer-Chisels, No. 2, 14", handled and sharpened. 2.21 12 Buck Brothers’ Firmer-Chisels, No. 2, %", handled and sharpened. 2.68 24 Buck Brothers’ Firmer-Chisels, No. 2, 1", handled and sharpened.. 7.31 24 Sloyd Knives, No. 7, 2%" . 6.50 12 Hammond’s Adze-eye Claw-Hammer, No. 3, 7 oz. 4.90 24 Try-squares, No. 5%, 6". 5.32 24 Beech Marking-Gages. No. 64%. 4.86 136 EQUIPMENT AND CARE OF THE SHOP. 137 24 Boxwood Rules, No. 3, 12" long.$ 1.80 12 Bench-Hooks . 2.00 12 Bench-Dusters, No. 10 . 2.70 Total for individual tools.$307.40 GENERAL TOOLS 6 Disston’s Crosscut-Saws, No. 9, 22", 10 points.$ 8.00 0 Disston’s Rip-Saws, No. 9, 22", 8 points. 8.00 2 Turning-Saws in frames, 14", M. F. & Co. 1.74 1 Dozen Turning-Saw Blades, 14", H. S. & Co. 1.06 2 Compass-Saws, Disston’s No. 2, 10", @ 27c. .54 1 Hack-Saw Frame, No. 50. .45 1 Disston’s Dovetail-Saw, 6", iron back. .48 1 Stanley Miter-Box, No. 240.•. 8.20 2 Stanley Block-Planes, No. 65%. 1.56 1 Stanley Fore-Plane, No. 6. 2.22 1 Stanley Rabbet-Plane and Filletster, No. 78. 1.10 1 Stanley “Bed Rock” Jack Plane, No. 605, 14". 1.98 6 Iron Spokeshaves, No. 54. 1.42 1 Veneer-Scraper, No. 80 . .70 6 Each Molding-Scrapers, No. 2 and No. 7. .90 1 Scraper Steel, Richardson’s, . .10 3 Flat Bastard Files, K. & F., 8", handled. .45 3 Half-Round Files, K. & F., 8", handled. .55 3 Rat-tail Files, K. & F., 8", handled. .33 4 Files, K. & F., 6", slim taper. .36 1 Auger-Bit-File .13 1 File-Card, No. 1 . .14 1 Empire Tool-Grinder . 2.80 1 Grindstone, No. 11, with stone . 15.00 1 India Oilstone, No. 0, in box . .95 1 Soft Arkansas Oil Slipstone, No. 6. .18 1 Copperized Steel Oiler, No. 14A, % pint. .23 2 Disston’s Sliding T Bevel, No. 3, 6". .46 1 Stanley Miter-Square, No. 16, 10". .60 1 Sargent Steel Square, No. 2. .69 3 Pairs Starrett’s Winged Dividers, No. 92, 8", @ 75c. 2.25 1 Chisel, No. 2, 14 ", handled . .20 3 Buck Brothers’ Firmer-Gouges, No. 8, 1". 1.29 1 Buck Brothers’ Gouge, No. 10, inside bevel, regular sweep, %"... .43 4 Barber’s Braces, No. 14, 6" sweep. 3.52 1 Barber’s Ratchet-Brace, No. 31, 12" sweep. 1.62 5 Gimlet-Bits, 1 each of 2/32", 3/32", 4/32", 5/32", 6/32". .40 1 Set Auger-Bits, R. Jennings’ . 4.46 1 Clark’s Expansive-Bit, small . .57 138 HANDWORK IN WOOD. 2 Screwdriver-Bits, round blade. No. 10, 4". $0.32 3 Hose Countersinks, No. 10, S/ & ” .. ,68 6 Brad-Awls, assorted 1"-1%" . .30 1 Hand-Drill, No. 5% . 2.45 Extra Drills, 2 each of No. 107, size, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, GO ... 1.42 G New Century Screwdrivers, 4" . .96 1 New Century Screwdriver, 12" . .54 6 O. K. Nailsets, assorted . .42 6 Carpenter’s Steel Bar Clamps, 3 ft. 9.60 12 Aldrich’s Oiled Handscrews, No. 16, 10". 4.79 12 Aldrich’s Oiled Handscrews, No. 17%, G". 3.42 4 Carriage-Maker’s Clamps, 6" . 1.32 1 Automatic Miter-Clamp . 1.80 1 Pair Pliers, No. 200, 5". .21 1 Coe’s Monkey-Wrench, 10" . .60 1 Glue-Pot, No. 3 . .82 1 Parker’s Wood-working Vise, No. 27G. 8.07 1 Gas Stove, 99A . .55 1 Pair End-Cutting Nippers, No. 154, 5". .88 1 Pair Compton’s Metal Snips, No. 12, 2". .63 1 Glass-Cutter, No. 10 .27 3 Flat Varnish Brushes, No. 54, 1%", hard-rubber-bound (for shellac) . .96 6 Cheap Brushes, 1", tin-bound (for stains), “EE”. .90 6 Extra Jack-Plane Cutters (No. 5) . 1.80 6 Enamel Cups, % pint . .60 1 Maple Yard-Stick, No. 41 . .17 Total for general tools .$120.54 Total for individual tools . 307.40 $427.94 Discount for schools, 10 per cent. 42.79 $385.15 Lockers for individual work .$150.00 Total .$535.15 $750 TOOL EQUIPMENT INCLUDING 1 BENCH AND SET OF TOOLS FOR INSTRUCTOR AND INDIVIDUAL TOOLS 25 Manual Training School Benches, Hammacher, Schlemmer