L8 PRICE 25 CENTS DIE CASTING DIES-MACHINES-METHODS BY CHESTER L. LUCAS MACHINERY'S REFERENCE BOOK NO. 109 PUBLISHED BY MACHINERY. NEW YORK h - MACHINERY'S REFERENCE BOOKS This treatise is one unit in a comprehensive Series of Reference books originated by Machinery, and including an indefinite number of compact units, each covering one subject thoroughly. The whole series 'comprises a complete working library of mechanical literature. The price of each book is 25 cents (one shilling) de- livered anywhere in the world. LIST OF REFERENCE BOOKS No. 1. Worm Gearing. — Calculating Dimensions; Hol)s; Looation of ritch Circle; Self-Loeljing Worm Gearing, etc. No. 2, Drafting-Room Practice.— Systems : Trac. ing. Lettering and Mounting. No. 3. Drill Jigs. — Principles of Drill Jigs; Jig Plates; Examples of Jigs. No. 4. Milling Fixtures. — Principles of Fix- tures; Examples of Design. No. 5. First Principles of Theoretical Mechanics. No. 6. Punch and Die' Work. — Principles of I'uncli and Die Worlj; Making and Using Dies; Die and Punch Design. No. 7. Lathe and Planer Tools. — Cutting Tools; rior'ng Tools; Shape of Standard Shop Tools; Forming Tools. No. 8. Working Drawings and Drafting.Room Kinks. No. 9. Designing and Cutting Cams. — Drafting of Cams; Cam Curves; Cam Design and Cam Cutting. No. 10. Ilzamples of Machine Shop Practice. — Cutting Bevel (Jears; Making a Worm.Gear; Spindle Construction. No. H. Bearings. — Design of Bearings; Causes of Hot Bearings; Alloys for Bearings; Friction and Lubrication. No. 12. Out of print. No. 13. Blanking Dies. — Making Blanking Dies; Blanking and Piercing Dies; Split Dies; Novel Ideas in Die Making. No. 14. Details of Machine Tool Design. — Cone Pulleys and ftelts; .Strength of Countershafts; Tumbler Gear Design; Faults of Iron Castings. No. 15. Spur Gearing. — Dimensions; Design; Strength; Durability. - No, 16. Machine Tool Drives. — Speeds and Feeds; Single Pulley Drives; Drives for High Speed Cutting Tools. No. IT. Strength of Cylinders. — Formulas, Charts, 'and Diagrams. No. 18. Shop Arithmetic for the Machinist. — Tapers: Change (Jears; Cutting Speeds: Feeds; InUexinj; Gearing for Cutting Spirals; Angles. No. 19. Use of Formulas in Mechanics. — With numerous apiilications. No. 20. Spiral Gearing. — Rules, Formulas, and Diagrams, etc. No. 21. Measuring Tools. — History of Standard Measurements; Calipers; Compasses; Micrometer Tools; Protractors. No. 22. Calculatior. of Elements of Machine De- sign. — Factor of Safety; Strength of Bolts; Rivet- ed Joints; Keys and Kejways; Toggle-joints. No. 23. Theory of Crane Design. — Jib Cranes; Shafts, Gears, and Bearings; Force to Move Crane Trolleys; Pillar Cranes. No. 24. Examples of Calculating Designs. — Charts in Designing: Punch and Riveter Frames; Shear Frames; Billet and Bar Passes, etc. No. 25. Deep Hole Drilling. — Methods of Drill- ing; Construction of Drills. No. 26. Modern Punch and Die Construction. — Construction and Use of Subpress Dies; Modern Blanking Die Construction; Drawing and Forming Dies. No. 27, Locomotive Design, Part I. — Boilers, Cylinders, Pipes and Pistons. No. 28. Locomotive Design, Part II. — Stei)hen- son and Walschaerts Valve Motions; Theory, Cal- culation and Design. No. 29. Locomotive Design, Part III. — Smoke- box; Exhaust Pipe; Frames; Cross-heads; Guide Bars; Connecting-rods; Crank-pins; Axles; Driving- wheels. No. 30. Locomotive Design, Part IV. — Springs, Trucks, Cab and Tender. No. 31. Screw Thread Tools and Gages, No. 32. Screw Thread Cutting. — Lathe Change Gears; Thread Tools; Kinks. No. 33. Systems and Practice of the Drafting- Room. Nc. 34. Care and Repair of Dynamos and Motors. No. 35. Tables and Formulas for Shop and Drafting- Room. — The U.se of Formulas; .Solution of Triangles: .Strength of Materials; Gearing; Screw Thre.itls; Tap Drills; Drill Sizes; Tapers; Keys, etc. No. 36. Iron and Steel, — Principles of Manu- failure and Treatment, No. 37. Bevel Gearing, — Rules and Formulas; Examples of Calculation: Tooth Outlines; Strength and Durability; Design; Methods of Cutting Teeth. No. 38. Out of print. See No. 98. No. 39. Fans, Ventilation and Heating. — Fans; Heaters; Shop Heating. No. 40. Fly-Wheels.— Their Purpose, Calcula- tion and Design. No. 41. Jigs and Fixtures, Part I. — Principles of Design; Drill Jig Bushings; Locating Points; Clamping Devices. No. 42. Jigs and Fixtures, Part II. — Open and Clo.sed Drill Jigs. No. 43. Jigs and Fixtures, Part III. — Boring and Milling Fixtures. "'Vo. 44. Machine Blacksmithing. — Systems, Tools and Machines used. (See inside back cover for additional titles) MACHINERY'S REFERENCE SERIES EACH NUMBER IS ONE UNIT IN A COMPLETE UBRARY OF MACHINE DESIGN AND SHOP PRACTICE REVISED AND REPUBLISHED FROM MACHINERY NUMBER 109 DIE CASTING DIES— MACHINES— METHODS By Chester L. Lucas CONTENTS Die Casting _-______3 Making Dies for Die-Casting Machines - - - 15 Van Wagner Mfg. Co.'s Die-Casting Practice - - 27 Ccpyright, 1913, The Industrial Press, Publishers of Machinery, 49-55 Lafayette Street, New York City '^ A^ V J--//^^^ ^.^j- CHAPTER I DIE CASTING Die-casting, a comparatively recent method for producing finished castings, is rapidly proving itself an important factor in the economical manufacture of interchangeable parts for adding machines, tj^pewriters, telephones, automobiles and numerous other products where it is essen- tial that the parts be nicely finished and accurate in dimensions. The term "die-casting" is self-explanatoiry, meaning "to cast by means of dies"; described briefly, the process consists of forcing molten metal into steel dies, allowing it to cool in them, and then opening the dies and removing the finished casting. It is the purpose of this treatise to give a general outline of the die-casting process, showing its possi- bilities and limitations, and also to give a description of the die-casting machinery and its operation, of the fundamental principles involved, and of the methods used in the die-making. Illustrative examples of the best types of dies, based on results obtained from actual experience, "will also be given. Origin of Die Casting The origin of the die-casting process is somewhat difficult to ascer- tain. We may look into the history of type founding and find that away back in 1S38, the first casting machine for type, invented by Bruce, was a machine that involved the principles of die-casting as it is prac- ticed to-day. More recently, in 1885, Otto Mergenthaler brought out the linotype machine. This machine is a good example of a die-casting machine. However, as we interpret the word to-day, die-casting is a broader term than type-casting or linotyping, although its development without doubt is due to the success of the linotype machine. It is doubtful if die-casting, properly speaking, was originated until about fifteen years ago, and it is certain that it is only during the past few years that the activities in this line have been very noticeable. One of the first experiments in the direction of die-casting was under- taken to get out some rubber mold parts cheaply enough to leave a profit on a job that was beginning to look dubious from the financial side. The molds were for making rubber plates about three inches square and one-eighth inch thick, the top side of which was decorated with fine raised scroll work; it was this latter feature that gave the trouble. After wasting much time and money trying to stamp the mold parts, a metal-tight box was made as shown in Figs. 1 and 2 with a block screwed in it, the purpose of which was to shape the mold impression and impart to it the scroll design. As shown, the ends of the box were removable, being screwed on. This box was placed under a screw press and a straight plunger that just filled the top of the box was fitted to the head of the press. After the two were lined up, molten type metal was poured into the box, and as soon as the metal had cooled to the "mushy" state, the ram of the press was forced down 4 No. 109— DIE CASTING as shown in Fig. 2. Next, the ends of the box were removed, the screw holding the block taken out, and the die-casting pushed from the box. The object in having the inclined side to the box was to produce a piece shaped with the proper inclination for its position in the final mold used for casting the rubber plates. The illustrations give an idea of the P=Fhf=^^ f^ ^ \ 1 \ 1 ~i k;.=t^^^3cJ w lSBehiner^,}f. T- Fig. 1. An Early Experiment in Die Casting — Before Applyingr Pressure Fig-. 2. An Early Experiment in Die Casting — After Applying Pressure compression that took place. The die-casting was found to be sharp at the corners and free from flaws, and the scroll work came up in fine shape. Naturally the rest of the mold parts were made in the same way and the job turned from failure into success. From such simple experiments as these, the die-casting industry has developed to its present stage. In view of the advances that have been made in die-casting, it is singular that there are to-day only DIE CASTING 5 about a dozen concerns in the business in this country, but as the sub- ject becomes better understood, and the possibilities of the process are realized, the demand for this class of castings will result in many other firms going into the work, and it is not improbable that a large number of factories will install die-casting plants of their own to aid them in producing better work in a more economical way. Advantag-es, Possibilities and Limitations of Die Casting The greatest advantage of die-casting is the fact that the castings produced are completely and accurately finished when taken from the dies. When we say completely, we mean that absolutly no machining is required after the piece has been cast, as it is ready to slip into its place in the machine or device of which it is to be a part. When we say accurately, we mean that each piece will come from the die an exact counterpart of the last one; and if the dies are carefully made, the castings will be accurate within 0.001 inch on all dimensions, whether they are outside measurements, diameters of holes or radii. All holes are cast and come out smoother than they could be reamed; lugs and gear teeth are cast in place; threads, external and internal, and of any desired pitch can be cast. Oil grooves can be cast in bear- ings, and, in a word, any piece that can be machined can be die-cast. The saving in machining works both ways; not only is all machine work eliminated by the one operation of casting, but the machine tools and the workmen necessary for their operation and up-keep are dis- pensed with, the expense of building jigs and fixtures is stopped; and no cutters, reamers, taps or drills are required for this branch of the production. In addition, the labor required for operating the casting machines may be classed as unskilled. No matter how intricate and exacting the machine work on a piece has been, and how skillful a workman was required to produce the work when machine-made, the same result may be brought about by die-casting, and usually the work is excelled, and, excluding the die-making, unskilled men can make the parts. From a metallurgical standpoint a die-casting is superior to a sand- casting on account of its density, strength and freedom from blow-holes. Also, when the hot metal comes in contact with the cool dies, it forms a "skin" similar to the scale on an iron sand-casting. As the die-casting requires no machining after leaving the dies, this skin increases the wearing qualities of the casting. The possibilities of die-casting are numerous. By this method of manufacturing it is possible and practical to cast pieces that could not possibly be machined. It is an every-day occurrence to make castings with inserted parts of another metal, as, for instance, a zinc wheel with a steel hub. It is also possible to make babbitt bearings that are harder and better than can be made in any other way. Often there are two or more parts of a device that have formerly been made separately, ma- chined and assembled, that can be die-cast as one piece. In such cases the saving in production is very great. Figures and letters may be cast sunken or in relief on wheels for counting or printing, and of 6 No. 109— DIE CASTING course ornamentation may be cast on pieces that require exterior finish. As to size, there is no definite limit to the work that can be cast. One job that is being done at the present time is a disk 16 inches in diameter with a round flange 1 inch in diameter, around the rim. "There is no great gain without some small loss," is just as true of a process like die-casting as it is of anything else. The limitations of this work are few, however, and they are here given so as to state the situation fairly. Generally speaking, a part should not be consid- Figr. 3. Examples of Die-castingrs ered for die-casting if there are but few pieces required, because the cost of the dies would usually be prohibitive. Often, however, it hap- pens that because of the large amount of accurate machine work being done on a machine part, it is economical to make a die for the com- paratively small number of parts required and die-cast them. A case illustrating this phase of the matter recently occurred in actual prac- tice. In getting out an order of two hundred vending machines, it was decided to try die-casting on a part that was difficult to machine. The dies were expensive, costing $200, and as there were only 200 pieces DIE CASTING 7 to be cast, the die cost per piece was one dollar; but even with that initial handicap, it was found that on account of the difficult machining that had formerly been required, the die-cast parts effected a large saving, and of course the results were superior. A rough part that would require little or no machining should not be die-cast, because pound for pound, the die-casting metals cost more than cast iron or steel. The casting machine cannot make parts as rapidly or of as hard metals as the punch press or the automatic screw machine. For this latter reason a part that necessarily must be made of brass, iron or steel, cannot be die-cast, although mixtures approximately equal in strength to iron and brass are readily die-cast. To give added strength to a die-cast part it is often advisable to add webs and ribs or to insert brass or iron pins at points that are weak or subject to hard wear. Roughly speaking, it is the part that has required a good deal of accurate machine operations that shows the greatest difference in cost when die-cast, and sometimes the saving is as great as 80 per cent. The Metals used in Die Casting- The metals that produce the best die-castings are alloys of lead, tin, zinc, antimony, aluminum and copper, and the bulk of the die-castings made at the present time are mixtures of the first four of these metals. From them, compositions may be made that will meet the requirements of nearly any part. For parts that perform little or no actual work, save to "lend their ■weight," such as balance weights, novelties and ornaments for show windows, etc., a mixture consisting principally of lead, often stiffened with a little antimony, is used. There is but little strength to this metal, but it is used because of its weight and low cost. For parts that are subject to wear, such as phonograph, telephone, gas-meter and adding machine parts, an alloy composed of zinc, tin and a small amount of copper is used. This alloy may be plated or japanned, and is a good metal to use on general work Another metal, used chiefly for casting pieces that have delicate points in their design but are not subjected to hard wear, consists prin- cipally of tin alloyed with lead and zinc to suit the requirements of the work. This mixture casts freely, and the finished castings come out exceptionally clean. Still another metal, used chiefly for casting pieces, that have letters and figures for printing, is similar to the standard type metal — 5 parts lead and 1 part antimony; but if there are teeth cast on the sides of the printing wheel a harder mixture will be re- quired to give longer life to the gears. The following mixtures are typical of die-casting or "white brass" alloys: copper, 10 parts; zinc, 83 parts; aluminum, 2 parts; tin, 5 parts. Another is copper, 6 parts; zinc, 90 parts; aluminum, 3 parts; tin, 1 part. Another containing antimony is copper, 5 parts; zinc, 85 parts; tin, 5 parts; antimony, 5 parts. Shonberg's patented alloy is copper, 3 parts; zinc, 87 parts; tin, 10 parts. Alloys containing 15 to 40 per cent copper and 60 to 85 per cent zinc are brittle, having low strength 8 No. 109— DIE CASTING and low ductility. An alloy of 8 per cent copper, 92 per cent zinc has greater resilience and strength but not the ductility of cast zinc. Aluminum may be cast, but it is a difficult metal to run into thin walls and fine details; it plays, however, an important part in some good mixtures used for die casting. Experiments are now being con- ducted for die-casting manganese bronze, and it is said that some Tery Pig, 4. General View of tbe Soss Die-casting Machine good castings have already been made. Its wearing qualities are so valuable that it is particularly desirable for making die-castings. The Die-casting' Machine The three important requisites for good die-casting are the machine, the dies and the metal. The casting machine is fully as essential as either of the other requisites, and although there are a number of different styles of casting machines in use, each of which has its advantages over the others, especially in the eyes of their respective designers, the fundamental principles upon which they all operate are the same. In each there is the melting pot and the burner, the cylinder and the piston foT forcing the metal jnto the dies, and the dies with DIE CASTING 9 the opening and closing device. In some machines pressure is applied to the metal by hand, in others power is used, and in still another class the metal is forced into the dies with compressed air. The provisions for opening and closing the dies vary in the different machines; there are various means employed for cutting the sprue, and the styles of heaters are numerous. One or two of the largest firms in the die-casting industry have automatic casting machines for turning out duplicate work in large quantities very rapidly. These machines are complicated and are only profitable on large quantities of work, and for that reason their use is not extensive. In general, their operating principles are the same as in the case of the hand machines, but provision is made for auto- matically opening and closing the dies, compressing the metal, and ejecting the castings. The Soss Die-casting Machine The Soss die-casting machine, manufactured and sold by the Soss Manufacturing Co., Brooklyn, N. Y., was the first die-casting machine to be placed on the open market. This machine is shown in Figs. 4 and 5, and in section in Fig. 6. The Soss Manufacturing Co. originally manufactured invisible hinges exclusively. At the advent of the die- casting era, they commenced to make these hinges from die-castings, and placed orders with a leading die-casting concern amounting to thousands of dollars each year. After the die-cast hinges had been on the market for a short time, complaints commenced to come in. some to the effect that the hinges were breaking and others that the hinges were corroding. Either of these faults was serious enough to blast the reputation of the hinge, but the first trouble, breakage, was the more important. Examination of the broken hinges showed that the castings were porous and full of flaws, and as the makers of the cast- ings could not produce castings sufficiently strong for the hinges, Mr. Soss started to experiment for himself. This experimenting led to the production of the Soss die-casting machine. Referring to the illustrations Figs. 5 and 6, A is the base and frame of the machine, B is the heating chamber located at one end of the machine, and within this heating chamber is the tank C. shown in Fig. 6. This tank contains the metal from which the die-castings are made, and the metal is heated by the burners D. These burners are fed by air and gas through piping on the side of and beneath the furnace. To facilitate lighting the burners and inspecting their condition at any time, there is an opening (not shown) through the firebrick lining of the furnace and the outer iron wall, on a level with the top of the burners. There is also another opening through the furnace wall to allow the gases due to the combustion to escape. Through the bottom of the tank, well to the inner side of the furnace, runs the cylinder E. Below the bottom of the tank, the cylinder makes a right-angle turn, extending through the furnace wall and terminating just outside of the wall. The orifice of this cylinder is controlled by gate F. In that part of the cylinder that extends upward into the tank, there is an 10 No. 109— DIE CASTING opening G that allows the molten metal to run into the cylinder from the tank. Working in this cylinder, is the piston H. that is used in forcing the metal into the dies. The compression lever 7, hinged over the inner furnace wall, is kept normally raised by spring pressure, and •is connected to the piston by means of the link J. Fig. 5. Working Parts of the Soss Die-casting- Maciine At the opposite end of the machine from the furnace, is the mechan- ism for operating the dies. This mechanism consists of a pair of square rods K. upon which are mounted the sleeves L. These sleeves have a long bearing surface and are attached to the die-plate M. Lever N at the end of the operating mechanism controls the movement of these sleeves by means of links 0. Upon these sleeves is mounted a secondary set of sleeves P. attached to the other die-plate Q. and whose DIE CASTING 11 movement is controlled by lever R. through links S. This second set of sleeves is free to travel with the first set. and in addition has an independent movement of its own on the primary sleeves. It is the function of lever R to bring die-plate Q up to die-plate M by means of links »S' and sleeves P; and it is the function of lever N to bring both of the die-plates up to the outlet of the cylinder by means of links and sleeves L. This system of sleeve-mounting is one of the dis- tinctive patented features of the Soss machine. The orifice of the cylinder E is conical in shape and exactly fits the cup-shaped opening in die-plate M. so that when the two are brought together, the joint is metal tight. At the center of this opening, and extending through the die-plate .¥. is an opening that leads to the dies mounted on the inner faces of the two die-plates, and a continuation of this opening extends through die-plate Q in which the sprue-cutter U works. Attached to the outer side of this die-plate are two slotted brackets. In the slot of one of these is pivoted the lever T. and in the slot in the opposite bracket are bolted two stops that limit the motion of the lever. This lever operates the sprue cutter U. that works through the opening in die-plate Q. The sprue-cutting mechanism is best shown in Figs. .5 and 6. At the left of Fig. .5 may be seen a rubber hose connected to the air piping. This hose is used for cleaning out the dies after each casting operation. Operation of the Die-casting- Machine The metal for the die-casting machine is mixed in the proper pro- poTtions for the work in hand by means of a separate furnace, before being poured into the tank of the machine itself. The burners are lighted and the dies are set up on the two die-plates. As soon as the machine has "warmed up." so that the metal is in a thoroughly melted condition, the sprue-cutting lever T is thrown back, leaving a clear passageway to the die cavities. Lever R is pulled backward, thus bringing die-plate Q up to die-plate M, which operation closes the two halves of the die. Then lever N is thrown forward, thereby bringing the closed die up to the body of the machine, with the nozzle in close contact with the outlet of the cylinder. Next, the gate F is opened, and the man at the compression lever I gives the lever a quick, hard pull, forcing the metal in the cylinder downward and into the dies. The molten metal literally "squirts" into the dies. Gate F is now closed; lever X is pulled back to remove the dies from the cylinder outlet; and the sprue-cutting lever T is pushed forward, cutting off the sprue and pushing it out of the nozzle into the kettle placed beneath it. The lever R is pushed forward, an:l a finished casting is ejected from the dies. An important advantage that this machine has over other die-casting machines is the fact that the metal for the castings is taken from the Lottom of the melting pot. whereas most other machines use metal fron?, the top of the tank. At the bottom of the tank the metal is always the best, as it is free from impurities and dross; hence, there is little chance for the formation of blow-holes. A handful of rosin thrown into 12 No. 109— DIE CAS'fiNG DIE CASTING 13 the melting tank occasionally helps to keep the metal clean, but the metal nearest the surface always contains more or less foreign matter. While this description of the operation of the die-casting machine may convey the idea that the process is a slow one, as a matter ol fact, the time required is, on the average, not over a minute and a half for turning out a finished casting. With the ejection of the casting from the dies, the product is completed, in theory; but in practice there are always a few small thin fins, caused by the air vents or by im- properly fitted portions of the dies. It is, however, but the work of a few seconds to break off these fins, and unless there are many of them, or they are excessively thick, they are detrimental neither to the qual- ity nor the quantity of finished castings. Points on the Operation of the Die-casting- Machine We have now taken up the description and general operation of the die-casting machine, but like every other machine, there are numerous little kinds and practices in its working the observing of which makes the difference between good and poor die-casting. Some of these points are here given. The casting machine is besj; operated by three men, one of whom attends to the compression lever and the metal supply in the tank. The other two men stand on each side of the die-end of the machine, and it is their duty to operate the sprue-cutter, open the dies and remove the finished casting, clean the dies with air and close them, throw back the die-plates to their casting position over the cylinder outlet, and do any other work incident to the operation of the machine. While it requires three men to operate a die-casting machine in the best manner, the man who attends to the compression lever has a good deal of spare time between strokes, and if two or even three of the machines are conveniently placed, one man can easily pull levers for all three. The metal should be kept just above the melting point and at a uniform temperature. If the metal is worked too cold, the result will manifest itself in castings that are full of seams and creases, and it will be difficult to "fill" the thin places in the dies. If, on the other hand the metal is allowed to get too hot, the die will tbrow exces- sively long fins, the castings will not cool as quickly in the die. and consequently they cannot be made as rapidly. On account of the im- portance of keeping the metal at a uniform heat, the fresh metal that is added to that in the tank from time to time, is kept heated in a separate furnace. Therefore, when the metal in the tank gets low, the new supply does not reduce the temperature of the metal being worked. Some casters use a thermometer to indicate the heat of the metal. Casting-dies require luorication frequently. Just how often they should be lubricated depends on the shape of the die, the composition of the casting metal, and the general performance of the dies. Bees- wax is the common lubricant, and the lubrication consists in merely rubbing the cake over the surfaces of the dies that come in contact with the casting metal. In die-casting large parts, the dies must be kept cool by some artificial means, for hot dies are conducive to slow 14 No. 109— DIE CASTING work and poor castings. To reach this end, large dies are sometimes drilled and piped so that water may be circulated through them to keep them cool. In the Soss machine, the burners are so placed that the metal in the cylinder is kept at a slightly higher heat than that in the tank proper. This condition is brought about by having the cylinder directly over the burners. The value of this feature lies in the fact that gas is not wasted in heating the entire tank full of metal to this higher heat, but still the metal under compression is at the required temperature. The gas consumption of the average die-casting machine is about 100 cubic feet per hour. The speed at which die-castings may be produced varies with the size of the castings being made, the composition of the metal being cast, and the style of dies that must be employed. In many cases, in die- casting, separate brass or steel pieces are used, that must be placed in the dies before each operation so that they will be inserted in and become a part of the finished casting. The dies may be diflB.cult of operation on account of draft problems or pins and screws that must be inserted in the dies and removed from each casting before another can be made. These different types of dies will be more fully described in the next chapter. Taken as a whole, from ten to sixty pieces per hour are the maximum limits for speed in die-casting, and with a well-working die, of simple construction, a speed of forty pieces per hour is con- sidered good production. It is possible, however, when the castings to be produced are small in size and simple in shape, to gate a number of them together, or rather to construct the dies so that six or more castings may be made at once. By this means it is often possible to cast five or six thousand pieces per day of ten hours, on a hand die-casting machine. CHAPTER II MAKING DIES FOR DIE-CASTING MACHINES The making of casting dies calls for ingenuity and skill of the highest order on the part of the die-maker. There is probably no class of die-making in which the work produced is more faithful to the dies, both in showing up the little details in the making that reflect credit on the dies, and in exposing the defects and shortcomings in the work- manship, if there be any. The castings from casting-dies or molds as they are sometimes called, may be produced in dimensions down to ten-thousandths for accuracy if necesasry. and once the dies are made the castings will not vary in the slightest degree, if the working con- ditions are kept uniform. In spite of the close work required in making casting-dies, the work is very .fascinating. Perhaps it is on account of this accuracy; possibly it is on account of the fact that they are made from machine steel; but most likely -i't is because there are no hardening troubles to be contended with. Another factor that makes the work interesting is the ingenuity required in the work, for almost every die-maker, if he is worthy of the name, likes to figure out and plan for the best way of building a die for a difficult job. General Principles of Casting--die Making- Casting-dies, or molds, have little in common with sand molds. It is true that the dies for die-casting are composed of two parts corre- sponding to the cope and nowel of the sand mold, but they are so different in every other way that no benefit would result from a com- parison. Generally speaking, casting-dies are made of machine steel; the parts which are exceptions are the heavy bases and frames, which are made of cast iron, and the dowel pins and small cores, usually made of tool steel. Except in rare instances, there are no hardened parts about a casting-die; this is the case because the melting points of some of the alloys that are die-cast are high enough to draw the temper from any hardened parts of the dies. The ideal die is simple in construction, with as few parts as practi- cable; the castings should be easily ejected and should come from the dies as nearly free from fins as possible. To meet these requirements in the best way is the proposition that confronts the ingenuity of the die-maker. As the die is primarily in two parts, there must be a parting line on the casting. This line is always placed at the point that will permit the casting to be ejected from the dies in the easiest manner possible, bearing in mind the effect the joint will have on the appearance of the finished casting; this is a point far less important than with sand casting, for, if the dies are properly made this seam will be barely perceptible. When it is practicable to do so, it is wise to have the parting line come on an edge of the die-casting. Draft is uuneees- 16 No. 109— DIE CA§TING sary on the straight "up-and-down" places, but of course it is impossible to draw any parts that are undercut. Means must be provided for ejecting the casting from the dies after completion and it is usually done by means of ejector pins, though frequently it is better to have the bottom of the die or some other section movable and do the ejecting on the same principle that is used on drawing dies of the compound type. On close work, shrinkage plays an important part, and the amount of shrinkage varies from 0.002 to 0.007 of an inch per inch. Aluminum shrinks the greatest amount, Parsons white brass shrinks considerably. while tin shrinks but little. Thus, it may be easily seen that to figure the shrinkage allowance for an alloy that contains three or four metals with different shrinkages, requires judgment. To pre- vent the air from "pocket- ing," air vents are necessary at frequent intervals around the die-cavity. These vents are made by milling a flat shallow cut from the die- cavity across the face of the Fig. 7. Disk cast in Simple Castingr-die ^jj^ ^^ jj^g OUtside edges of the block. From y^ inch to % inch is the usual width and from 0.003 to 0.005 of an inch, the customary depth, varying with the size and shape of the die in question. The dies ot molds for die-casting are of various styles, as are also punch-press dies, and it would be difficult to lay down specific rules for their classification. There are the plain dies, without complications of any kind; slide dies with one or more slides; dies for bearings, both of the "half-round" and of the "whole-round" types; dies for gated work; and many other less important classes. Then there are dies that have features that belong to more than one of these tjT)es, so that it is easily seen that to decide upon the style of die that would be best for a given piece of work requires a good deal of experience. Some of the most important of these types can best be shown by illustrating dies made in the various styles, showing, step by step, how the dies are made and assembled. To begin with, consider the making of a casting-die of the very simplest form. In Fig. 7 is shown a plain flat disk made by die-casting. In actual practice, a die would not be made for such a simple piece, unless there were some features about it that would prevent it being made on a screw machine or with press tools. It might have a cam groove cut in one of its flat sides, the sides might be covered with scroll work, there might be gear teeth around its circumference, or a hundred and one other conditions to make die-casting a desirable method of manu- facturing. All these complications are omitted for the sake of simpli- fying this initial description of a casting-die. THE MAKING OF THE DIES 17 Fig. 8 shows the die for this piece in plan and sectional elevation. A is a square cast-iron frame, made from a single casting. This frame or box. as it is generally called, is planed on the top and bottom only. Next, the two die-halves B and C are shaped up from machine steel. In this casting-die, and in the majority of others, these die blocks are c Machinery, !f.Y. Fig-. 8. Simple Casting-die for Casting BlocJi shown in Fig. 7 square. The lower half of the die B is held to the cast-iron frame by fillister head screws, set in counterbOTed holes, thus sinking the screw- heads under the surface of the block. The upper half of the die C is located upon B by dowel pins driven into B which have a sliding fit in 18 No. 109— DIE CASTING the reamed holes iu C. This being done, the die-half B is fixed to the faceplate of the lathe and the recess bored for the die-cavity. This operation is a simple one in this case, for it is merely a straight hole one-half inch deep and three inches in diameter. Of course this recess must be carefully finished with a tool that has been stoned up to a sharp edge, using lard oil. Emery cloth should be used as little as possible. It is unnecessary to give this hole draft, but it must be free from ridges or marks that would prevent the casting from being pushed out. If the faces of the dies are spotted with a small piece of box wood or rawhide held in the drill press and kept charged with flour emery, the die-cast- ing will reproduce this "bird's-eye" finish and the appearance will well repay the few minutes additional time that it will take. The spotting should be done with dry emery (without oil) to get the brightest finish. The upper die-half C is simply ground on its working face. The outside corners and edges of the faces of both die-halves should be well rounded off so as to insure the absence of slight dents or rough places that might prevent the dies from fitting perfectly. The ejecting mechanism must next be considered. Lever D. pivoted from bracket E, has a steel pin F that engages in the elongated hole in bracket G. so that an upward pull of the lever D raises bracket G, which is attached to ejector-pin plate H. This plate is a loose fit over the guide screws I that are attached to the lower die-half B. The ejector pins J, four in number, in this die, are riveted into the ejector- pin plate, and they work through holes drilled and Teamed through the lower die-half. The ends of these pins must be finished off so as to lie perfectly flush with the inside of the die when ready for operation and, of course, they must be a sliding fit in the holes in the die. ^ An important feature of a casting-die is the sprue cutter, shown in this die at K. If the disk for which this die was made, had had a hole or central opening of any kind, the sprue cutter would best be operated at that point; but, as this disk is plain, the sprue cutter must be placed at the edge. At the outside of the die-cavity, as shown in Fig. 8, the opening for the sprue cutter is laid out, drilled and filed to shape. It is obvious that the side of the sprue cutter adjacent to the die must fit the outline of the die perfectly, so that there will be no break in the appearance of the casting. The opening for it is extended through the upper die-half, and from a point % of an inch from the inside face of the die this hole is fiared out nearly as large as the opening through the die-plate of the machine. Of course the apperture in the upper die- half must be no larger than the opening through the die-plate; other- wise the sprue could not he pushed out. The sprue cutter itself is a long rod. whose section is of the same shape and size as the openings just made, and it is connected to the sprue cutting mechanism of the machine. Of course it is unnecessary to shape the entire length of the sprue cutter to size; after the working end is milled to shape for a distance of six or eight inches, the rest of the rod may be left round. The sprue cutter is finished first, after which both the openings in the die are fitted to it; and while the fit should he metal tight, it must be perfectly free to slide. THE MAKING OF THE DIES 19 The dies are mounted on the die-plates of the casting machine by means of straps, much the same as bolsters are held on punch press Deds. The position of the die on the die-plate must be such that the opening for the sprue cutter will line up with the nozzle at the outlet of the cylinder. At the time of casting, the position of the sprue cutter is as shown in the illustration of this die, Fig. 8. In this position there is room for the metal to enter the die-cavity, and yet there is but a small amount of metal to be cut off and pushed back after the die has been filled with metal. With slight modifications, the above style of die may be used for die- casting any piece that will draw or pull out of a two-part die. If holes must be cast through the piece, it is only necessary to add core pins to the lower die B, a point that will be more fully described later. It is unnecessary to add that both halves of the die may be utilized in making the cavity for the die, should they be needed. Also, it is often easier to machine out the recess larger than is needed, and set in pieces in which parts of the outline of the die-casting have been formed. Gear teeth are put in the die in this way; a broach is cut similar to the gear desired, then hardened and driven through a piece of steel plate which is afterward fitted to its place in the die. Slide Dies The die illustrated in Fig. 9 is one of the most successful of the various types of casting-dies, and if properly made is an interesting piece of die work. The prinicpal use of this particular style of die, called a slide die, is to cast parts like the one shown in Fig. 10, which, is a disk similar to the one which the last die described was to cast, except that it has raised letters at the edge and a hole in the center. It is obvious that the die last described, (Fig. 8), would not do for disks or other pieces having projections or depressions around their edges, as, for instance, printing or counting wheels with raised or sunken characters, or grooved pulleys. Briefly, this style of die is similar to the simple casting-die, except that slides are provided, to the required number, which form the edge of the casting. A die for a 'plain grooved pulley would require but two slides, while a die for a printing wheel with forty letters around its edge would necessitate forty slides, one for each of the letters. The die about to be described, shown in Fig. 9, was made to cast a wheel with six iraised letters. Referring to Fig. 9, D is the cast-iron box or frame, E, the lower die, and F the upper die. In making the lower die-half, the stock is first shaped to size and doweled to the blank for the upper die-half, and the holes for attaching to the frame are drilled. For the sake of clearness, these holes and screws are omitted from the illustration as are also the vents, since they have been fully explained. The lower die is next strapped to a face plate, trued up, and bored out nearly to the diameter of the body of the piece to he cast, exclusive of the raised letters. The depth of this recess is equal to the thickness of the printing wheel plus 3/16 inch to allow for the cam ring G that is used to reciprocate the slides of the die. The cam ring is made large enough to cover the die- 20 No. 109— DIE CASTING cavity as well as the slides that surround it, with an allowance of an inch or two for the cam slots H. The six slides / are made long enough to have good bearing surfaces. With the size of the cam ring deter- mined, the die is next bored out to receive this cam ring and the last inch of the recess is carried down to the depth of the die cavity so as to make an ending space for the slots that the slides are to work in. SECTION ABO Maehineru,N. Y. Fig. 9. Slide Die lor Casting- the Printing- "Wheel sbo-wn In Fig. lO The die is now taken from the faceplate and the slots for the slides laid out. These slots may be milled or shaped, but milling is to be preferred. The next step is the making and fitting of the slides, which are of machine steel, having a good sliding fit in the slots. The six slides are fitted in position and left with the ends projecting into the die proper. THE MAKING OF THE DIES 21 The slots H are next profiled in the cam ring G. and the pins / that ■work in them are made and driven into the holes in the slides. With the slides and cam ring in place, the cam ring lis rotated to bring all the slides to their inner position where they are held temporarily by means of the cam ring and temporary screws. The die-half with the slides thus clamped in the inner or closed position, is set up on the lathe faceplate and the die-cavity indicated up and bored out to the finish size, which operation also finishes the ends of the slides to the proper radius. The die may now be taken down and the slides removed to engrave the letters upon their concave ends. The engraving can be done in the best manner on a Gorton engraving machine, but if such a machine is not available they may be cut in by hand. Stamping should never be resorted to for putting in the letters, because the stock dis- placement would be so great that it would be impossible to refinish the surface to its original condition. Before fitting the cam ring, an open- ing must be milled in the die to allow the handle to be rotated the short distance necessary. After the cam ring has been fitted, it is held in by the four small straps K. attached by screws to the lower die-half at the corners. The sprue cutter, which is not shown, is operated through the hole in the center of the piece and is, of course, round in this Fig. ID. Printing Wheel cast in a Slide Die ^jg Its action is the Same as was the one previously described, and the ejecting device is similar, with the exception that the brackets L that are attached to the ejector-pin plate M, are widely separated so as to make room for the sprue cutter that works through a hole in the plate M. Die for Casting with Inserted Pieces For making die-castings that are to have pieces of another metal inserted, it is necessary to have a die With provisions for receiving the metal blank and holding it firmly in position while the metal is being cast around it, and of course the piece must be held in such a manner that it can be easily withdrawn from the die with the finished casting. The die illustrated in Fig. 11 is for a part that is used as a swinging weight, shown in Fig. 12. The upper part of the piece is made from a sheet steel punching, so as to lighten this part of the piece as well as to give increased strength, especially at the hole at the pivoted end of the work. The cast portion of the piece is slotted lengthwise, as the •illustration shows; and three holes pass through the casting, piercing the sides of the slot. In addition to showing the method of making dies for Inserted pieces, this die shows the principles of simple coring. 22 No. 109— DIE CASTING In making this die, two machine-steel blanks are planed up for the ?ipper and lower halves of the die, A and B, the lower die being made nearly twice as thick as the upper die because it is in this part that ihe most of the die-cavity will be made. In this lower half of the die K^ J V o TlaShinery.V.'i. Fig. 1 1 . Casting-die for Making- Castings -with Inserted Pieces like that shown in Fig. 12 the stock is milled out to the same shape as the outline of the plan view of the casting, being carried down to the exact depth of the thick- ness of the casting. From the wide end of this recess the stock is milled or shaped out in a parallel slot to the outside of the die-block. THE MAKING OP THE DIES 23 At the bottom of the side of this wide slot are T-slots to guide the slide E that is to work in this opening. The side is milled and fitted to the T-slots and opening in the die, but is left considerably longer than the finish size. Next, the slide is mounted on the faceplate of a lathe and turned out on the end with the proper radius and a tongue to form the slot that is to be in the curved end of the casting. At the outer end of the slide is left a lug that is drilled and tapped for the operating lever F that reciprocates the slide, using the stud in bracket K as a fulcrum. Two pieces of machine steel are next shaped and finished up to form the chamfered part of the casting and to locate the inserted steel punching in the die. The combined thickness of these pieces C and D is equal to the thickness of the casting, less the thickness of the in- serted piece. It is now an easy matter to seat section D in the bottom of the milled part of the lower die-half, and to locate section C in its proper position on the upper half. A pilot pin M is fitted in D to hold the steel punching in position by means of the hole that is in the extreme upper end of the punching. The pilot pin extends through this hole into a cor- responding hole in section C. At the lower end of the steel part that is inserted, there are two holes the object of which is to secure the punching to the die- casting, for the molten metal runs through these holes, practically riveting the die-casting to the inserted piece. Provision has now been made for holding the sheet-metal part that is 10 be inserted, and the cavity has been completed for the casting, in- cluding the tongue at the end; it now remains to describe the manner of forming the holes that pierce the casting through the slotted por- tion. In the lower die-half the positions of the three holes H are laid out, drilled and reamed. Then, with the two die-halves together ?ni the slide clamped at its inner position, the holes are transferred through the slide and the upper die. This being done, it is an easy -natter to make core pins and drive them into the upper die at the two end holes, the center hole being taken care of by the sprue cutter L that will be described later. The core pins should be a nice sliding fit through ;^he slide and in the holes in the lower die, into which they should extend from a quarter to half an inch. In addition to coring the holes, these pins act as a lock to hold the slide L' in its proper position at the time of casting. The sprue cutter L is most conveniently operated in the center hole, thus doing away with the core pin that would otherwise be re- quired. The sprue cutter needs little description in this die, for as in Fig-. 12. Die-cast Weierht -with Inserted Sheet-steel Punching 24 No. 109— DIE CASTtNG the slide die, It is merely a plain round rod that fits closely in the holes through the dies and slide. The ejector mechanism is the same in this die as in the dies already described; therefore further descrip- tion is unnecessary. /<^ 11 v fe y-!-- - iai (11 it^ Ho 1 1 u \\ ll I I ■ ! I 'm Oil li i I ®im?^J \ ±j- ' w 1 / 1 1 1 ( ^-_-^ c C;=J 1 i Machinery, N. Y, Fig. 13. Oastingr-die for the Halt-round Bearing: shown In Fig. 14 The operation of this die is very simple. The sheet-steel piece is laid in the recess in the open die. being located by the pin M. Slide E is thrown in by means of lever F. and the dies are closed. At the THE MAKING OF THE DIES 25 time of casting, the sprue cutter in is the position shown in the sketch, being nearly through the die-cavity. As before explained, this position admits the molten metal to pass into the die-cavity, but still leaves very little sprue to be cut off after the die-casting is completed. It should be stated that the steel piece that is inserted must be per- fectly flat and free from burrs that would prevent the die-halves from coming together properly. Bearing Dies Bearing dies are one of the most important of the various classes of casting-dies. The bearings produced by die-casting are so far superior to those made by other casting methods and machining that their use is now very extensive. Dies are made for "half-round" and "whole- round" bearings. There is little out of the ordinary about a whole- round die. but the half-round die involves many interesting methods of die-making, and for that reason is here described. Fig. 13 shows a casting-die for half-round bearings. Half-round bear- ing dies are usually made to cast two bearings at a time, for the reason that it is just as easy to cast two pieces of such a shape as it is to cast one, and, in addition, the die is balanced in a better manner. As with other dies, the first step is to machine up the frame A and the - -- f-\ / x'' ^^^A-727'l,''' ^N J"^ Machinery.N.Y. Fig-. 14. Die-cast Half-round Bearing-, Sho-wing the Cast Oil Grooves two die-halves B and C. The pieces B and E that are to form the insides of the bearings are then turned up and one side of each shaped and keyed to fit the slots that have previously been milled in die-half C. These parts are held in place by dowels and screws. One of the bearings produced by this die is shown in Fig. 14, and it will be noticed that there is an oil groove within that covers the length of the bearing. To produce this groove in the die-castings, a shell must be turned up and bored out whose Inside diameter is that of the inside of the bearing, and whose thickness equals the depth of the oil groove. This being done, the oil grooves are laid out upon the shell and cut out by drilling and filing. After rounding the outside corners, these little strips are pinned to the cores D and E in their proper places. Another little kink in this connection is worthy of noting. So many different styles and sizes of bearings are made by a concern doing much die-casting that it is essential that the die-cast bearings should bear some distinguishing number to identify them. As this number is of no consequence to the user it is well to have the number in an incon- spicuous place, but it must be where it will not be effaced by scraping, etc. Bearing in mind that it is much easier to produce raised lettering by die-casting than to produce sunken lettering, it will be readily seen 26 No. 109— DIE CAg*riNG that the oil groove affords a good place in which to put the bearing numbeir. This is easily done by stamping the figures upon the narrow strip that forms the oil groove. In this place on the bearing it may be easily found if needed, and of course there is no danger of its being taken out by machining. The lower die consisis of two blocks F and G, each of which contains an impression of a bearing. The best way to make these parts is to lay out the ends of each of the blocks with the proper radius, taking care to have the center come a little below the surface of the face of the block. Then the blocks should be shaped out to get the bulk of the stock out. before setting up in the lathe. After the lathe work is done Fig. 15. Interesting- Examples of Die-castings on each piece, which of course is usually done separately, the faces of ihe two blocks are faced down just to the exact center of the impres- sion. It will be noticed that two blocks are used for the lower part of the die. The reason is to facilitate the locating of the female parts of the die in proper relation to the male parts. After properly locat- ing, they may be doweled and screwed to baseplate B. The sprue cutter H, better shown in the plan view, is square in shape and connects with the die-cavities in a thin narrow opening on either side of the sprue cutter. The ejector pins, /. two to each die. are at the ends of the bearings. The ejector-pin plate J is necessarily ■•arge, and is operated by lever K. Fig. 15 shows a number of interesting examples of die-castings. CHAPTER III VAN WAGNER MFG. CO.'S DIE-CASTING PRACTICE In 1907, Mr. E. B. Van Wagner, of Syracuse. N. Y., established the E. B. Van Wagner Mfg. Co. for the production of die-castings. The fac- tory comprises the office section, the machine shop where the dies and casting machines are built, the metallurgical laboratory where the metals are alloyed, the casting department shown in Fig. 17 where the die-castings are made, and the trimming department. Possibilities and Limitations of Die Casting At the outset we may say that it is possible to die-cast almost any piece, but it is not by any means practicable to do so. It must be remembered that to die-cast on a practical basis the dies must be con- ^ L .' \^ 1 / \ / \ /-'■'' \ / - - ■ / /' ' /^ A / B C Tachinery Fig. 16. Die-casting- Constructions to be avoided structed in such a manner that the cost of their operation and up-keep will be light, or there will be no profit in die-casting. It is impractic- able to produce under-cut work, that is, work having no draft and which is therefore impossible to draw from the die. Such an instance is that illustrated at A, Fig. 16, and by the internal section of M, Fig 21. and the internal groove in 0, also shown in Fig. 21. If abso- lutely necessary, work of this kind can be done by the use of collapsi- 'rle cores; but here, again, we meet resistance in maintaining the dies :n proper condition, and, moreover, this method is commercially im- practicable, owing to the difficulty of operating these cores rapidly. Hollow work, requiring curved cores, like faucets and bent piping of the character illustrated at C in Fig. 16, are difficult to produce. If, in designing the piece, it can be planned to have the parts of such a shape that the cores can be readily withdrawn, employing a two-piece core with a slight draft in each direction, the division coming as indi- cated by the core line of C in Fig. 16, the problem becomes simpler. Oftentimes this worK can best be done by casting in a straight piece. 28 No. 109— DIE CASTING 0) o "3 o 0) to CO CO o c/T s > -a o -a CO 03 -a . CO o3 CO CO ^ ^ H a; B "o 03 0) CO o3 J3 -t-> > CO CO o O bJ3 O CO 03 o3 o 33 ,Q 'C -*-> S bO >J o en 2 o3 bjO "3 > 03 'co o3 -u IS O CD o 4-> s Oi Tt "to ^ bC cc 1—1 03 OJ C "", a> 0) OJ -*j CO •"^J"' u CI ■ft CO u 03 ft CO o3 CO CO CL> 03 bo o "c^ o o i=l CO a; o K CO a> o3 >> -w OS TS _co s .^ CO CO -i-> ft o3 !^ o o c o CO o O o c •i-i CO o '■tJ '^ "co -tJ "O Q) >1 > CI OS ^ "cO bO u o3 rt CO O "a! CC d o CO en o >> o3 o3 c -u OS '> o3 CO 0) ft > O o a) -a CO O '3 Oi o o CM -3 OJ o S m CD O -t-> CO CO bC a; 1 CO ft o W) .2 *3 '3 11! c bo c3 X3 o CD "3 o q; s "ft o3 CD ^ be 15 a 2 03 > _a> C !S s o o o '3 oi CO -tJ -kJ OJ ^ '3 S CO be 03 03 o 3 bo o s 03 CO X OJ o a> ^ o bi -3 03 O cd 0) s u M '3 g CO 01 S CO an cr ]3 o3 C4-I O 03 ^i^ ^ 5^ i ^^y-^'m 'm •55 ^- H "* •Ji o rri ^ ^H H cS s ^ h M ^ ■i-' ^ ^ r"^ 03 3h X e^ o o ^ o b fl fH bo • l-H o Ik >. -o -O iS 03 o 0) a; o 'p. Hi ca (1) ■a a ^ t>, ^ frt ui <<-i o Ik p o Wl o CI 44 No. 109— DIE CASHING plate being held against the under side of the die-plate by means of the pinion shaft. The operation being done is the drilling of the ejector pin holes. Referring back to Fig. 32, which by the way shows the die here illustrated disassembled, the holes being drilled are those shown at F for the I'eception of the pins E. The method employed is to drill the holes through the die and into tha Pigr. 39. Indicatingr a Mold on the MiUlng Machine ejector plate, afterward reaming all holes to size and driving the pins into position in the ejector plate, while they are allowed to slide freely through the die-plate. We will now assume that the ejector box and plate have been completed and fitted, a pinion shaft for operating this plate also fitted, the lower and upper dies completed by the machining operations previously described, and all assembled. The final oper- ation of the fitting of the pins is shown in Fig. 41 in which the die- maker may be seen filing off the ends of these pins so that when dropped to the lower position they will lie flush with the surface. If of uneven lengths, these pins will cause irregular spots in the casting. It now remains to describe the toggles used for operating the cores which form the holes through the three lugs in the casting. One of these toggles, of which there are three, is shown at 7. in Fig. 31. and also in Fig. 32. MACHINES AND METHODS 45 These toggles consist of brackets which are attached to the die-plate, and levers which are fulcrumed at the ends of the brackets so that their operation works the core pins. It is necessary to remove these core pins after each casting has been made and position them before another casting can be produced. The fitting of the parts of a die-casting mold is one of the most important parts of the work. It demands the highest type of work- Fig-. 40. DriUing- the Ejector-pin Holes manship, for a poorly fitted die means a die which works hard in addition to producing poor castings. It is very important that all mov- able parts should work freely. Fig. 42 shows the assembling operation on a die-casting mold, the casting which is to be duplicated being shown in the immediate foreground. These parts must all be screwed into their respective places, making the joints as nearly air-tight as possible. One cause of poor die-castings arises from the trapping of air in the die, and different methods are employed for overcoming this trouble. Venting the Dies There are two methods of preventing air from being trapped in die- casting molds; either by constructing the dies so that the air may be 46 No. 109— DIE CITING exhausted from the mold cavity before admitting the metal, or by iVenting the die so that the air may be forced out by the inrushing metal. In the first of these methods it is necessary that the joints in the mold be made as close as possible, otherwise it will be impossible to produce anything like a vacuum in the mold cavity. If, however, it has many parts which must be fitted, it is usually considered advisable to provide the die with vents consisting of milled recesses a few thous- andths inch deep. Several vents are provided, from which the air can Fig. 41. Fitting Ejector-pins escape when the metal is admitted to the dies. The hot metal, of course, "shoots" through them in thin ribbons, but not enough escapes to affect the pressure on the metal which goes into the casting. No matter how carefully a die may have been constructed, or how carefully it has been assembled, there is always a certain amount of "babying" to be done before it will work satisfactorily. The casting may stick a little here, or there may be a rough spot there, and it is the successful elimination of these troubles which constitutes the pro- duction of a good die-casting. MACHINES AND METHODS 47 Die-castingr Metals One of the purposes of this book is to correct several erroneous im- pressions which are prevalent in regard to die-casting possibilities. Many people seem to think that nearly all metals can be die-cast, but as a matter of fact, those metals which can be successfully die-cast can be numbered on the fingers of one hand, being alloys of lead, zinc, tin, copper and antimony. The tin base metals shrink very little, while the zinc base metals shrink considerably, and those with a large per cent of aluminum have a very high shrinkage. Without doubt, the most used die-casting metals are the zinc base metals. A typical metal of this class contains about 85 per cent zinc; 8 per cent tin; 4 per cent copper and 3 per cent aluminum. The melting point of this metal is Fig. 42. AssembUng a Die-casting Mold about 850 degrees F. While this alloy is one of the most common, it is not by any means the best, as there is too little tin employed, but it is a comparatively cheap metal, which probably accounts for its large use. This metal is easily affected by heat and cold, and rapidly de- teriorates with age. The lead base metals may be typified by an alloy containing 80 per cent lead; 15 per cent antimony; 4 per cent tin; and 1 per cent copper. This composition melts at approximately 550 degrees F. and is used for castings subjected to little wear and where no great strength is required. The weight of this metal is its greatest objection, and it is also quite brittle because of the large per- centage of antimony. For the best class of die-castings, the tin base metals are employed. These range from 60 to 90 per cent tin, and from 2 to 10 per cent copper, together with a little antimony. The melting point of a mixture of this composition is about 675 degrees F. The castings have a good color and they are much better in quality than any of the other alloys. JUL 24 }^\i 48 No. 109— DIE CASfflNG It is absolutely eeeential that tin base metals be used for carbureter parts or other parts coming in contact with gasoline. Also, the tin base metals must be used for parts which come in contact with food products, as the lead or zinc alloys have a contaminating effect. Aluminum alloys have been cast in France and Germany in limited quantities, but very seldom in this country on account of their high melting point, as well as their effect upon the die. After aluminum alloys have been run in the dies for a short time, the surfaces of the molds become pitted. Through some unexplained cause, the metal seems to flake out particles of the steel in the molds. When an aluminum alloy is to be used, a good mixture is 80 per cent aluminum, 3 per cent copper and 17 per cent zinc. This alloy has a high shrinkage and it has also the same deteriorating effect upon the dies, but to a much less degree than pure aluminum. No. 46. Drop Forging. — Lay-out of Plant; Meth- ods of Drop Forging; Dies. No. 46. Hardening and Tempering. — Hardening Plants; Treating Higli-Speed Steel; Hardening Gages. No. 47. Electric Overhead Cranes. — Design and Calculation. No. 48. Files and Filing. — Types of Piles; Using and Mailing Files. No. 49. Girders for Electric Overhead Cranes. No. 50. Principles and Practice of Assembling Machine Tools, Part I. No. 51. Principles and Practice of Assembling Machine Tools, Part II. No. 52. Advanced Shop Arithmetic for the Machinist. No. 63. Use of Logarithms and Logarithmic Tables. No. 54. Solution of Triangles, Part I. — Methods, Itules and Examples. No. 68. Solution of Triangles, Part II. — Tables of Natural Functions. No. 56. Ball Bearings, — Principles of Design and Construction. No. 67. Metal Spinning. — Machines, Tools and Methods Used. No. 68. Helical and Elliptic Springs. — Calcula- tion and Design. No. 69. Machines, Tools and Methods of Auto- mobile Manufacture. No. 60. Construction and Manufacture of Auto- mobiles. No. 61. Blacksmith Sbop Practice. — Model Blacksmith Shop; Welding; Forging of Hooks and Chains; Miscellaneous. No. 62. Hardness and Durability Testing of Metals. No. 63. Heat Treatment of Steel. — Hardening, Tempering, Case-Hardening. No. 64. Gage Making and Lapping. No. 65. Formulas and Constants for Gas Engine Design. No. 66. Heating and Ventilation of Shops and Offices. No. 67. Boilers. No. 68. Boiler Furnaces and Chimneys, No. 69. Feed Water Appliances. No. 70. Steam Engines. No. 71. Steam Turbines. No. 72. Pumps, Condensers, Steam and Water Piping. No. 73. Principles and Applications of Elec- tricity.^Statie Electricity; Electrical Measure- ments; Batteries. No. 74 Principles and Applications of Elec- tricity. — Magnetism; Electro-Magnetism; Electro- Plating. No. 75. Principles and Applications of Elec- tricity. — Dynamos; Motors; Electric Railways. No. 76. Principles and Applications of Elec- tricity. — Electric Lighting. No. 77. Principles and Applications of Elec- tricity. — Telegraph and Telephone. No. 78. Principles and Applications of Elec- tricity. — Transmission of Power. No. 79. Locomotive Building. — Main and Side Rods. No. 80. Locomotive Building. — Wheels; Axles; Driving Boxes. No. 81. Locomotive Building. — Cylinders and Frames. No. 82. Locomotive Building. — Valve Motion. No. 83. Locomotive Building. — Boiler Shop Practice. No. 84. Locomotive Building. — Erecting. No. 85. Mechanical Drawing. — Instruments; Materials; Geometrical Problems. No. 86. Mechanical Drawing. — Projection. No. 87. Mechanical Drawing. — Machine Details. No. 88. Mechanical Drawing. — Machine Details. No. 89. The Theory of Shrinkage and Forced Fits. No. 90. Railway Repair Shop Practice. No. 91. Operation of Machine Tools. — The Lathe, Part I. No. 92. Operation of Machine Tools. — The Lathe, Part II. No. 93. Operation of Machine Tools. — Planer, Sbaper, Slotter. No. 94. Operation of Machine Tools. — Drilling Machines. No. 95. Operation of Machine Tools.— Boring Machines. No. 96. Operation of Machine Tools. — Milling Machines, Part I. No. 97. Operation of Machine Tools. — Milling Machines, Part II. No. 98. Operation of Machine Tools. — Grinding Machines. No. 99. Automatic Screw Machine Practice. — Operation of the Brown & Sharpe Automatic Screw Machine. No. 100. Automatic Screw Machine Practice. — Designing and Cutting Cams for the Automatic Screw Machine. No. 101. Automatic Screw Machine Practice. — Circular Forming and Cut-ofif Tools. No. 102. Automatic Screw Machine Practice. — External Cutting Tools. No. 103. Automatic Screw Machine Practice. — Internal Cutting Tools. No. 104. Automatic Screw Machine Practice. — Threading Operations. No. 106. Automatic Screw Machine Practice. — Knurling Operations. No. 106. Automatic Screw Machine Practice. — Cross Drilling, Burring and Slotting Operations. No. 107. Drop Forging Dies and Die-Sinking. — A Complete Treatise on Die-sinking Methods. No. 108. Die Casting Machines. No. 109. Die Casting. — Methods and Machines Used; the Making of Dies for Die Casting. No. 110. The Extrusion of Metals. — Machines and Methods Used in a Little-known Field of Metal Working. No. 111. Lathe Bed Design. No. 112. Machine Stops, Trips and Locking De- vices. — Also includes Reversing Mechanisms and Clamping Devices. ADDITIONAL TITLES WILL BE ANNOUNCED IN MACHINERY FBOX TIME TO TIME LIBRARY OF CONGRESS • 003 318 242 9 • MACHINERY'S DATA SHEini or^x^xiijo Machinery's Data Sheet Books include the well-known series of Data Sheets originated by Machinery, and issued monthly as supplements to the publication; of these Data Sheets over 500 have been published, and 6,000,000 copies sold. Re- vised and greatly amplified, they are now presented in book form, kindred sub- jects being grouped together. The pl'ice of each book is 25 cents (one shilling) delivered anywhere in the world. CONTENTS OF DATA SHEET BOOKS No. 1, Screw Threads. — United States, Whit- worth, Sharp V- and British Association Threads; Briggs Pipe Thread; Oil Well Casing Gages; B'ire Hose Connections; Acme, Worm and Metric Threads; Maehine, Wood, Lag Screw, and Car- riage Bolt Threads, etc. No. 2. Screws, Bolts and Nuts. — Fillister-head, Headless, Collar-head and Hexagon-head Screws; Standard and Special Nuts; T-nuts, T-bolts and Washers; Thumb Screws and Nuts; Machine Screw Heads; Wood Screws; Tap Drills. No. 3. Taps and Dies. — Hand, Maehine. -Tapper and Machine Screw Taps: Taper Die Taps; Sellers Hobs; Screw Machine Taps; Straight and Taper Boiler Taps; Stay-bolt, Washout, and Patch-bolt Taps; Pipe Taps and Hobs; Threading Dies. No. 4. Reamers, Sockets, Drills and Millinir Cutters. — Hand Reamers; Shell Reamers and Ar- bors; Pipe Keaniers; Taper Pins and Reamers; Brown & Sharpe, Morse and Jarno Taper Sockets and Reamers; Drills; Wire Gages; Milling Cutters; Setting Angles for Milling Teeth in End Mills and Angular Cutters, etc. No. 5. Spur Gearing. — Diametral and Circular Pitch; Dimensions of Spur Gears; Tal)les of Pitch Diameters; Odontograph Tables; Rolling Mill Gear- ing; Strength of Spur Gears; Horsepower Trans- mitted by Cast-iron and Rawhide Pinions; Design of Spur Gears; Epicyclie Gearing. No. 6. Bevel, Spiral and Worm Gearing. — Rules and Formulas for Bevel Gears; Strength of Bevel Gears; Design of Bevel Gears; Rules and Formulas for Spiral Gears; Diagram for Cutters for Spiral Gears; Rules and Formulas for Worm Gearing, etc. No. 7. Shafting, Keys and Keyways.— Horse- power of Shafting; Strcngtli of Shafting; Forcing, Driving, Shrinking and Running Fits; Woodruff Keys; Standard Keys; Gib Keys; Milling Key- ways; Duplex Keys. No. 8. Bearings, Couplings, Clutches, Crane Chain and Hooks. — Pillow Blocks; Babbitted Bear- ings; Ball and Roller Bearings; Clamp Couplings; Flange Couplings; Tooth Clutches; Crab Couplings; Cone Clutches; Universal Joints; Crane Chain; Crane Hooks; Drum Scores. No. 9. Springs, Slides and Machine Details. — Formulas and Tables for Spring Calculations; Ma- chine Slides; Machine Handles and Levers; Collars; Hand Wheels; Pins" and Cotters; Turn-buckles. No. 10. Motor Drive, Speeds and Feeds, Change Gearing, and Boring Bars.— Power required for Machine Tools: Cutting Speeds and Feeds for Carbon and High-speed Steel; Screw Machine Speeds and Feeds: Heat Treatment of High-speed Steel Tools; Taper Turning; Change Gearing for the Lathe; Boring Bars and Tools. . Machinery, the leading journal in the the 25-cent Reference and Data Books, yearly. Foreign subscription, $3.00. No. 11. Milling Machine Indexing, Clamping Devices and Planer Jacks. — Tables for Milling .Ma- chine Indexing; Change Gears for Milling Spirals; Angles for setting Indexing Head when Milling Clutches; Jig Clamping Devices. No. 12. Pipe and Pipe Fittings. — Pipe Threads and Gages; Cast-iron Fittings; Bronze Fittings; Pipe Flanges; Pipe Bends; Pipe Clamps and Hangers. No. 13. Boilers and Chimneys. — Flue Spacing and Bracing for Boilers: Strength of'Boiler Joints; Riveting; Boiler Setting; Chimneys. No. 14. Locomotive and Railway Data. — Loco- motive Boilers; Bearing Pressures for Locomotive Journals; I^ocomotlve Classifications; Rail Sections; Frogs, Switches and Cross-overs; Tires; Tractive Force; Inertia of Trains; Brake Levers. No. 15. Steam and Gas Engines, -.-Saturated Steam; Steam Pipe Sizes; Steam Engine Design; Volume of Cylinders; Stuffing Boxes; Setting Cor- liss Engine Valve Gears; Condenser and Air Pump Data; Horsepower of Gasoline Engines; j> jtomo- bile Engine Crankshafts, etc. No. 16. Mathematical Tables. — Squares of Mixed Numbers; Functions of Fractions; Circum- ference and Diameters of (Mrdes; Taldes for Spac- ing off Circles; Solution of Triangles; Formulas for Solving Regular Polygons; Geometrical Pro- gression, etc. No. 17. Mechanics and Strength of Materials. — Work; Energy; Centrifugal Force; Center of Grav- ity; Motion; Friction; Pendulum; Falling Bodies; Strength of Materials; Strength of Flat I'lates; Strength of Thick Cylinders, etc. No. 18. Beam Formulas and Strncttiral Design, — Beam Formulas; Sectional Moduli of Structural Shapes; Beam Charts; Net Areas of Structural Angles; Rivet Spacing; Splices for Channels and I- beams; Stresses in Roof Trusses, etc. No. 19. — Belt, Rope and Chain Drives. — Dimen- sions of Pulleys; Weights of Pulleys; Horsepower of Belting; Belt Velocity; Angular Belt Drives; Horsepower transmitted by Ropes; Sheaves for Rope Drive; Bending Stresses in Wire Ropes; Sprockets for Link Chains; Formulas and Tables for Driving Chain. • No. 20. Wiring Diagrams, Heating and Ventila- tion, and Miscellaneous Tables. — Typical Motor Wiring Diagrams; Resistance of Round Copper Wire; Current Densities for Various Contacts and Materials; Centrifugal Fan and Blower Capaci- ties; Hot Water Main Capacities; Decimal Equiva- lents. Metric Conversion Tables. Weights and Specific Gravity of Metals, Drafting-room Con. ventions, etc. machine-building field, the originator of Published monthly. Subscription, $2.00 The Industrial Press, Publishers of Machinery, 49-55 Lafayette Street, New York City, U. S. A.