\\-b.^ my ~7zr^£»?' '/*/>£ '~c- ??& EXPLORATORY TESTS ON MACHINING AND RELATED PROPERTIES OF FIFTEEN TROPICAL AMERICAN HARDWOODS April 1949 tfE L/Sf I AUG 1 3 ti *'V Of Florid icrida No. R1744 UNITED STATES DEPARTMENT OF AGRICULTURE FOREST S ERVICE FOREST PRODUCTS LABORATORY Madison 5, Wisconsin In Cooperation with the University oi Wisconsin Digitized by the Internet Archive in 2013 http://archive.org/details/rytestsOOfore EXPLORATORY TESTS ON MA.CMINING AND RELATED PROPERTIES OF FIFTEEN TROPICAL AMERICAN KAKDVJOODS By E. Li. DAVIS, Technologist Forest Products Laboratory,— Forest Service U. S. Department of Agriculture Introduction The Forest Products Laboratory is increasingly receiving requests from American importers and manufacturers for information on tropical American hardwoods. The objectives of the work here reported were to obtain information on the machining and related properties of fifteen of these woods for compari- son with native hardwoods and to determine to what extent the tests that have already been developed for native hardwoods are applicable to tropical species • The machining properties that were investigated were planing, shaping, turn- ing, sanding, boring and mortising. The related properties of specific gravity, cross grain, and shrinkage were also investigated because of their relation to the general utility of the woods • Test Material In most of the species ten or more samples were available for test. Exhaustive tests would require more material but this amount suffices to give good indi- cations of machining and related properties. The fifteen woods, which are listed below, all came from Central America or northern South America except coigue, which came from Chile. They, of course, do not represent all of the tropical hardwoods but are all- species on which the Forest Products Laboratory has received requests for information on one or more of the properties inves- tigated. Scientific Name Name Anacardium sp. Brosimum alicastrum group Calophyllum brasiliense Carapa guianensis Espavel U juste Santa Maria Crabwood (cedro macho, andiroba) "Maintained at Madison 5, Wis. in cooperation with University of "Wisconsin. Report No. R1744 -1- Hieronyma • alchorneoides Nectandra sp. Nothofagus sp. Prioria copaifera Symphonia globulifera Virola sp. Vochysia hondurensis Scientific Name Name Cordia alliodora group Laurel Dialyanthera sp. Cuangare Enterolobium cycloca r pum Jenezero (Guanacaste) Pilon Chachajillo Coigue Cativo Mapelo Banak San Juan Zanthoxylum sp. Prickly yellow A very confused situation exists concerning the common names of tropical American hardwoods. The same species often goes by different common names in different regions, and the same common name is sometimes applied to different species in different regions. In general the common names used above are those designated by the shippers and are names in common use. To insure identifying the woods beyond possibility of misunderstanding, the botanical names are used in all the tables of this report. Test Procedure The same general test procedure was followed as that described in detail in U. S. Dept. Agr. Tech. Bull. 824, "Machining and Related Characteristics of Southern Hardwoods •" It was not practical to make all of the tests described in that bulletin, however, nor to do as much work on the effect of machining variables. All test material was dried to 6 percent moisture content. Machining Tests Planing Samples were planed at 3,600 r.p.m. at feeds of 29 and 58 f.p.m. using a 30° cutting angle. The results, which are shown in table 1, show both the planing quality of the woods and the occurrence of planing defects. Comparison of the planing properties of the tropical hardwoods is based on the percentage of defect-free pieces and varies from 15 percent to 90 percent for different species. This compares with a range of 21 percent to 91 percent for native hardwoods and gives a good indication of the amount of sanding that may be required to prepare the woods for any fine finish. Report No. R1744 -2- The kinds of planing defects and their frequency of occurrence are also shown. For any given defect the occurrence may range from none up to very common in different woods. Shaping Tests were made on a two spindle shaper operating at 7,200 r.p.m., and cuts were made at angles that varied from parallel to grain to right angles. The shaping properties of the woods tested, taking all defects into account, are shown in table 2. The percentage of good to excellent pieces varies in different species from 28 percent to 67 percent. This is a better showing than was made by native hardwoods, which ranged from 3 percent up to 62 per- cent. This difference is chiefly due to the larger proportion (among native hardwoods) of light woods that are soft and shape poorly. Rough cutting on end grain was the most common shaping trouble as with native hardwoods. In most species it was the sort of superficial roughness that sands off without too much trouble, but in some of the lighter woods small tearouts sometimes occurred. Turning Turnings of uniform size and pattern were made on a modified back-knife lathe after which they were carefully examined for defects and graded for quality. Results are shown in table 3. Quality comparison is based on the percentage of good to excellent turnings that were obtained. This varied from 40 percent to 90 percent in different tropical woods as compared with a range of 58 percent to 91 percent for 25 native hardwoods. Surface roughness was the most common defect encountered but it can usually be removed by a little sanding. Detail refers to corners and edges that are damaged instead of being sharp and clear cut. A wood may, however, be somewhat poor in detail, but still satisfactory for turnings of sorts that do not require sharp detail. Tearouts, as the name indicates, are spots where bits' of wood have torn out in turning. These are rare except in light soft woods, and in cuts approaching right angles to the grain. Sanding A small drum sander with garnet abrasive in the l/O and 3/0 grit sizes was used. After sanding the samples were examined for scratches and fuzziness and comparison of species was based on the percentage of samples in each wood that was free from these defects. Results are given in table 4. Only one of the woods, coigue, had pores too fine to be seen with the naked eye and most of them had pores so coarse that they tended to obscure fine Report No. R1744 -3- scratches. This accounts for the fact that 13 of the 16 woods showed 80 per- cent or more of scratch free pieces when sanded with l/o grit. None of the woods showed visible scratches when 3/b grit was used. As a rule, fuzzing was more prevalent than scratching in sanding these tropical hardwoods* Although fuzzing is greatly reduced when 3/0 grit is used, most of the woods still developed some fuzzy pieces. Boring Two holes were bored in each sample with a small boring machine using a stand- ard type one inch bit. The holes were graded for smoothness of cut and measured with a plug gage for variation from the size of the bit or off size (see table 5). Percent of good to excellent holes (as far as smoothness was concerned) varied from 40 up to 100 as compared with a range of 62 to 100 for 25 native hardwoods. The range in off size or variation from the size of the bit is practically identical with that in 25 native hardwoods. Mortising Two mortises were cut in each sample using a hollow chisel mortiser of the half inch size. The holes were graded for smoothness of cut and for variation from the size of the hollow chisel. Tropical hardwoods like native ones vary widely in mortising properties and this comparison is shown in table 6, The proportion of fair to excellent mortises based on smoothness of cut ranged from 11 to 100 or about the same as for native hardwoods* The amount of offsize of the mortises (or variation from the size of the chisel) was from 0.0027 to 0.0077 or somewhat more than in native hardwoods on the average. Related Properties Specific Gravity Specific gravity of the woods tested (based on oven-dry' weight and green volume) is given in table 7, The lightest wood, virola, is practically the same as basswood in this respect and the heaviest, pilon, is slightly heavier than hickory. Specific gravity yields a good clue not only to strength properties but to power consumption and rate of dulling of tools in machining. Cross Grain The presence of spiral grain was determined by splitting small samples and making measurements. The average slope of spiral grain ranged from 2,5 Report No, R1744 -4- percent to 8.3 percent in different woods or about the same as for native hardwoods (table 0). Presence of interlocked grain was determined by examination and splitting but accurate measurement was not practical • This is a more extreme type of cross grain. Two-thirds of our native hardwoods have little if any interlocked grain, but 11 of 15 tropical hardwoods had more or less of it including four species in which every piece had interlocked grain. Flat sawed boards with interlocked grain sometimes twist in drying while quarter sawed boards with the same type of grain not only season much better but often show an attractive ribbon stripe figure. Shrinkage Shrinkage from green to 6 percent moisture content is shown in table 9, In all v/oods tangential material was available for test, and radial material also was available in 8 woods. In general the shrinkage was about the same as for native hardwoods both in spread between species and in maximum and minimum species. Shrinkage is directly related to warping tendencies and hence to "ability to stay in place." Summary and Conclusions Table 10 gives a summary of the results of the machining tests. Some of the species tested are consistently better than average in most respects and some are consistently poorer. Some are good in one property and poor in others. These things are equally true of native hardwoods* In general the tropical woods machined about as well as do our native hardwoods and with most of them at least it seems unlikely that machining difficulties would restrict their use much. The woods tested had a specific gravity range about equal to that between basswood and hickory. Within this range, which includes the great bulk of tropical hardwoods, the machining tests that were used appear to be equally applicable to native and tropical hardwoods. Report No. R1744 -5- Table 1. --Planing 1 Planing ; 1 Species j properties , Planing defects Defect-free i Raised ; Fuzzy j Chipped pieces ; grain ; grain : grain Percent : Anacardium sp. : 15 : Very common. Very common; None Brosimum alicastrum group ! 70 : None i None s Common Calophyllum brasiliense : 43 Common Trace Common Carapa guianensis s : 33 : Trace Trace Common Cordia alliodora group : 75 Trace None j None Dialyanthera sp« i 50 : Trace ; Trace : Trace Enterolobium cyclocarpum ; 35 : G ommon ! Trace ; Common Hieronyma alchorneoides : 20 : C ommon t None Common Nectandra sp. : 75 : C ommon : None : Trace Nothofagus sp» ; 90 : None : None : None Prioria copaifera ! 85 None : None Trace Symphonia globulifera : 50 ; Common : None : Common Virola sp. : 60 : Trace : Trace : Trace Vochysia hondurensis : 33 ;Very common : None : Trace Zanthoxylum sp» : 75 : None ; None : Trace Table 2.— Shaping Shaping : properties ; Shaping defects Species ; Good to j Rough i Raised Chipped excellent ; end grain ; grain grain pieces j , Percent ; Anacardium sp» 50 i Very common : Common : Trace Brosimum alicastrum group ; 60 Very common ; None i Trace Calophyllum brasiliense : 45 Very common Common : Trace Carapa guianensis ; 28 .Very common [Very common : Trace Cordia alliodora group i 50 Very common ; Common : None Dialyanthera sp. ; 40 Very common ;Very common ; None Enterolobium cyclocarpum : 45 ;Very common [ None : Trace Hieronyna alchorneoides : 40 .Very common : None ! Trace Nectandra sp. : 50 :Very common : Common i None Nothofagus ep» i 67 : Trace : Hone t None Prioria copaifera : 50 :Very common ; Trace : None Symphonia globulifera : 40 :Very common t Common i None Virola sp. : 45 :Very common :Very common I None Vochysia hondurensis P 43 :Very common : Common : Trace Zanthoxylum sp. : 50 ;Very common t None : None Report No, R1744 Table 3. --Turning : Turning Species : properties : Turning defects ; Good to : Surface : Poor ; Tearouts excellent roughness detail , : pieces : Percent Anacardium sp. ; 70 Common : None Brosimum alicastrum group : 90 i Trace : None Calophyllum brasiliense ; 70 Common : X : None Carapa guianensis : 70 Common : None Cordia alliodora group 83 : Common : None rialyanthera sp. 50 Trace : X ; Few Enterolobium cyclocarpum ; 75 : Common : None Hieronyma alchorneoides i 80 Trace : None Nectandra sp. : 80 Common : None Prioria copaifera : 80 ! Trace : None Symphonia globulifera j 83 : Common : : None Virola sp. : 50 : Trace : X : Few Vochysia honcurensis : 40 : Common : X : Few Zanthoxylum sp. : 90 ; Trace : None Table 4. --Sanding Species : Scratch-free pieces : Fuzz-fre se pieces l/O grit 3/0 grit l/O grit '3/0 grit Percent 100 Percent ; 100 Percent , Percent Anacardium sp. : : i : Brosimum alicastrum group : 33 : 100 : 67 : 100 Calophyllum brasiliense ; 88 : 100 : ! 88 Carapa guianensis ; 100 : 100 : 16 i 50 Cordia alliodora group : 100 100 ; : 100 Dialyanthera sp. : 50 : 100 : : ; 80 Enterolobium cyclocarpum 85 ! 100 : 36 : 73 Hieronyma alchorneoides : 90 100 : 100 : 100 Nectandra sp. 100 100 : 33 67 Nothofagus sp. : : 100 : 20 ! 100 Prioria copaifera : 100 ! 100 : 50 Symphonia globulifera : 100 : 100 : 16 : 83 Virola sp. : 70 : 100 : : 80 Vochysia hondurensis : 90 : 100 : 30 i 70 Zanthoxylum sp. i 100 : 100 : 33 : 100 Report No, R1744 Table 5. — Boring Good to : excellent holes- Amount of Species : offsize Percent : Inch Anacardium sp. : 70 : 0.0012 Brosimum alicastrum group j : 90 ! .0002 Calophyllum brasiliense : 77 : .0006 Carapa guianensis : 86 : .0011 Cordia alliodora group : : 100 : .0015 Dialyanthera sp. 50 : .0008 Enterolobium cyclocarpum [ 95 i .0003 Hieronyma alchorneoides : 100 : .0020 Nectandra sp. ! 75 ; .0013 Nothofagus sp. : 84 i .0024 Prioria copaifera : 75 I .0009 Symphonia globulifera ! 100 : .0008 Virola sp. : 50 i .0015 Vochysia hondurensis i 62 : .0010 Zanthoxylum sp. : 83 : .0010 —Based on smoothness of cut. Table 6. — Mortising Fair to i excellent holes— , Amount of Species : offsize : Percent : Inch Anacardium sp. 90 : 0.0038 Brosimum alicastrum group : 100 ! .0028 Calophyllum brasiliense : 78 .0027 Carapa guianensis : 72 .0028 Cordia alliodora group : 75 : .0032 Dialyanthera sp. : 11 : .0077 Enterolobium cyclocarpum : 80 : .0030 Hieronyma alchorneoides : 100 t .0028 Nectandra sp. : 67 : .0049 Nothofagus sp. : 100 ; .0041 Prioria copaifera ; 55 : .0034 Symphonia globulifera ! 100 : .0030 Virola sp. : 30 : .0052 Vochysia hondurensis : 75 : .0043 Zanthoxylum sp. : 50 i .0034 —Based on smoothness of cut. Report No. R1744 Table 7. --Specific gravity (Based on oven-dry weight and green volume) Species lie an : Minimum : L.aximum Anacardium sp. ; 0,463 : 0.403 ; 0.540 Brosimum alicastrum group : .620 : .575 : .680 Calophyllum brasiliense ; .490 .444 : .530 Carapa guianensis : .496 : .427 : .580 Cordia alliodora group ; .489 : .460 : .510 Dialyanthera sp. : .351 : .313 : .416 Enterolobium cyclocarpum : .456 ; .392 : .546 Hieronyma alchorneoides : .651 { .580 : .700 Nectandra sp# . .422 : .395 : .465 Nothofagus sp. : .542 : .498 : .595 Prioria cooaifera : .416 ; .376 ; .477 Symphonia globulifera : .544 : .470 ; .593 Virola sp. : .410 ! .380 : .465 Vochysia hondurensis : .415 ; .383 : .456 Zanthoxylum sp. : .588 ; .505 : .683 Table 8. — Cross grain Spiral grain : Interlocked grain Species ; Percent^of : : slope— j Percent of pieces i Anacardium sp. ; 100 Brosimum alicastrum group ; C.3 : 25 Calophyllum brasiliense 6.5 i 50 Carapa guianensis i 7.7 : 50 Cordia alliodora group : 3.1 Dialyanthera sp. : 6.7 5 Enterolobium cyclocarpum 100 Hieronyma alchorneoides 100 Wectandra so. 4.0 67 Mothofagus sp. 2.5 : Prioria copaifera : 3.4 Symphonia globulifera : • 5.5 : 40 Vochysia hondurensis ; 6.2 50 Zanthoxylum sp. : 4.4 —Applies only to pieces that are free from interlocked grain. Report No. R1744 Table 9. --Shrinkage (from green to oven-dry) All : Radial : Tangential Species : samples : only ! only : Percent : Percent : Percent Anacardium sp. : 4.6 : 4.1 : 5.8 Brosimum alicastrum group Calophyllum brasiliense Carapa guianensis -, : 6.9 : 8.7 7.6 6.9 8.7 : 6.4 ! 9.3 Cordia alliodora group ; Dialyanthera sp. Enterolobium cyclocarpum j 6.5 8.6 4.5 6.5 8.6 : 3.0 : 5.4 Kieronyma alchorneoides : 5.6 : 4.8 ; 6.4 Kectandra sp. : 5.2 : 4.1 : 6.2 Uothofagus sp. ; Prioria copaifera j 8.6 5.2 8.6 : 4.4 : 5.6 Symphonia globulifera Vochysia hondurensis : 7.4 i : 3.6 7.4 : 2.8 . : 6.5 Zanthoxylum sp. : 6.7 : 6.7 N> = a> = ©= 00 = 0>35= i : X ■c Table 10. --Summary of machining properties Planing; Shaping Turning i Sanding . Boring Mortising defect-; good to ; good to fuzz-free, good to , fair to Species : ■ free excellent: .excellent : pieces ; ■excellent, excellent pieces : pieces pieces pieces : pieces Percent Percent 50 : Percent ; 70 ■ Percent : : : Percent 70 Percent Anacardium sp. : 15 ; i 90 Brosimum alicastrum group, 70 i 60 ; 90 100 : 90 : 100 Calophyllum brasiliense 43 : 45 : 70 : 88 : 78 : 78 Carapa guianensis 33 ; : 28 ; 70 ; 50 ; 86 : 72 Cordia alliodora group ; 75 ; 50 : 83 ; 100 ; 100 : 75 Dialyanthera sp. : 50 , : 40 ; : 50 80 : 50 : 11 Enterolobium cyclocarpum , 35 ; 45 ; 75 : 73 ; 95 ; ; 80 Hiercnyma alchorneoides 20 ; 40 s 80 i l 100 ; 100 : 100 Mectandra sp. ; 75 ! 50 ; : 80 : 67 : 75 ! 67 Uothofagus sp. , 100 ; 67 !••••••••• : 100 : 84 : 100 Prioria copaifera ! : 85 : 50 : 80 : 50 : 75 ! 55 Symphonia globulifera ; : 50 : 40 : 83 ; 83 : 100 ; 100 Virola sp. j ! 60 i 45 : 50 : 80 : 50 ! 30 Vochysia hondurensis : 33 ; 43 : 40 : 70 : 62 : 75 Zanthoxylum sp. : 75 : 50 : 90 : 100 : 83 : 50 Mean of 1£ tropical j hardwoods ! 53 : 47 : 73 : 76 : 81 : 72 Mean of 25 native hard- woods : 61 : 25 : 79 : 62 : 89 ; 70 iort No, R1744