EN RY IKK Schneider How lo install electric! belffi ann unci alo&, and alarms V- •M , i'W' 4> 'tt Jffc , ' vaS; HOW TO INSTALL qtriq Bells, 2lNNUN@m TORS, and Alarms. INCLUDING tteries. Wires and Wiring, Circuits, Pushes, Bells, E Alarms, High and Low Water Alarms, Fire Alarms, Thermostats, Annunciators, and the Location and Remedying of Troubles. By NORMAN H. SCHNEIDER LEARN TO DO THINGS Model Library Series OF COPYRIGHTED BOOKS 1. The Study of Electricity for Beginners, 2. Dry Batteries, How to Make them. 3. Electrical Circuits and Diagrams, Part 1. 4. Electric Bells, Annunciators and Alarms. 5. Modern Primary Batteries. 6. Experimenting with Induction Coils. 7. Electric Gas Igniting Apparatus. 8. Small Accumulators, How to Make and Use 9. Model Steam Engine Design. 10. Practical Electrics. 1 1. Inventions, How to Protect and Sell them. 12. Woodwork Joints, How to Make and Use. 13. The Fireman’s Guide to the Care of Boilers 14. The Slide Valve Simply Explained. 15. The Magneto Telephone. 16. The Corliss Engine and Its Management. 17. Making Wireless Outfits. 18. Wireless Telephone Construction. 19. The Wimshurst Machine, How to Make It. 20. Simple Experiments in Static Electricity. 21. Small Electrical Measuring Instruments. 22. Electrical Circuits and Diagrams, Part 2. 23. Induction Coils, How to Make Them. 24. Model Vaudeville Theatres, 25. Alternating Currents, Simply Explained. 26. How to Build a 20 foot Bi-plane Glider. 27. A B C of the Steam Engine. 28. Simple Soldering, Hard and Soft. 29. Telegraphy for Beginners. 30. Low Voltage Lighting with Storage Batteri es 33. House Wiring for Electric Light. 34. Magnets and Magnetism. 36. Small Windmills and How to Make Therm 31. Lieckfield Gas and Oil Engines. 37. Collin's Wireless Plans, Part 1. 38. Collin’s Wireless Plans, Part 2. IN PAPER COVERS PRICE 35 CENTS EACH HOW TO INSTALL Electric Bells, Annunciators, and Alarms. INCLUDING Batteries , Wires and Wiring, Circuits, Pushes, Bells , Burglar Alarms, High and Low Water Alarms, Fire Alarms, Thermostats, Annunciators , and the Locatio?i and Remedying of Troubles . B Iv NORMAN HT SCHNEIDER, Author of “The Study of Electricity for Beginners,” “Care and Handling of Electric Plants,” etc., etc. THIRD EDITION, ENLARGED NEW YORK SPON & CHAMBERLAIN, 120 LIBERTY STREET LONDON E. & F. N. SPON, Limited, 57 HAYMARKET, S.W, 1918 CONTENTS Introduction Page Introduction. The principle of an electric bell. ix Chapter I The Leclanche cell — Polarization — Setting up — The dry cell — The gravity cell — Connecting up cells . 1 Chapter II The single stroke bell — The shunt bell — The differen- tial bell — The continuous ring bell — The water- proof bell — Forms of gongs — The buzzer — Long distance bells — The relay — The push — Three point or double contact push — Floor push — Door pull — Indicating push 9 Chapter III Bell wires — Joints — Running wires — How to put up a door bell — Combinations of bells, pushes and bat- teries — Faults in bells, faults in wiring — How to locate and remedy faults 23 vi CONTENTS Chapter IV Page Fire alarms — Thermostats — Metallic thermostats — Mer- cury thermostat — How to connect thermostats — Water level indicators — Burglar alarms — Open and closed circuit alarms — Window, door and shade springs — Alarm matting — Yale lock alarm — Doo trip alarm 40 Chapter V The annunciator drop — The needle or arrow drop — The pendulum drop — Wiring up annunciators — Return or fire call systems — Double wire system — Western Electric single wire system .... 55 Chapter VI Three-.wire return call system — Installing elevator an- nunciators — Burglar alarm annunciators — Clock alarm circuit — Bells for high voltages — Bell-ringing transformers — Combination bell, door opener and telephone circuits — Fire alarm circuit — interior fire alarm system — Fire alarm system for considerable areas 64 LIST OF ILLUSTRATIONS Fig. Page 1 Electric bell, push, and battery x 2 Leclanche cell 1 3 Dry cell 4 4 Gravity cell 5 5 Vibrating bell 10 6 Single stroke bell 10 7 Shunt or short circuit bell 10 8 Continuous ring bell 13 0 Waterproof bell 14 10 Dome gong 15 11 Tea gong 15 12 Cow gong 15 13 Sleigh bell gong 15 14 Spiral gong 15 15 Relay and circuit 16 16 Door push 19 17 Pear push 19 18 Door push 19 19 Wall push 19 20 Floor push 20 21 Door pull attachment 22 22 Wire joint first operation 25 23 Wire joint second operation 25 24 Wire joint insulating 25 25 Section of house showing wiring 29 26 Bell with ground return 30 27 Pushes in multiple , 31 viii LIST OF ILLUSTRATIONS Fig. Page 28 Bells in series 31 29 Bells in multiple 31 30 Two bells and two pushes 32 31 Two bells and two pushes 32 32 Two bells, two pushes and one battery .... 33 33 Double contact push 33 34 Grounded bell 34 35 Tongue test of wiring 38 36 Knife test of wiring 38 37 Knife test of wiring 30 38 Metallic thermostat 40 39 Mercury thermostat 41 40 Mercury thermostat circuit 42 41 Water level alarm 44 42 Lever water level alarm 45 43 High or low water level alarm 45 44 Window spring for burglar alarm 47 45 Burglar alarm — closed circuit 47 46 Special bell connection for burglar alarm ... 48 47 Special bell connection for burglar alarm ... 49 48 Burglar alarm and relay 50 49 Window-shade contact spring 51 50 House wired for burglar alarm 52 51 Door trip alarm 53 52 Annunciator drop .... 55 53 Needle drop 56 54 Needle drop indicating 50 55 Pendulum drop 57 56 Annunciator drop circuit 58 57 Simple annunciator circuit 59 58 Annunciator and fire call circuit 60 59 Single- wire room and fire call 6X LIST OF ILLUSTRATIONS Fig. -x Page 60 Three-wire return call circuit 65 61 Elevator bells and annunciator circuit 67 62 Burglar alarm annunciator circuit 69 63 Clock alarm circuit 71 64 Bell-ringing transformer 73 65 Bell-ringing transformer with three secondary * voltages 73 66 Western Electric interphone system 75 67 Western Electric interphone system for more ex- tensive service 77 68 Fire alarm circuit 79 69 Interior fire alarm circuit 81 70 Fire alarm circuit for considerable areas 82 INTRODUCTION An electric bell depends for its action on the fact that a piece of iron wound with insulated wire becomes a magnet and will attract another piece of iron just so long as an electric current is allowed to travel through the wire. The instant the current ceases, the magnetism also ceases, and the attracted piece of iron (termed the armature) is no longer held in contact. The general construction of an electric bell is shown in Fig. 1. M M are coils of insulated wire wound on soft iron cores. A is a soft iron armature mounted on a flat spring so that it is normally kept a slight distance away from the soft iron cores. 5” is a brass screw with a plat- inum tip touching a platinum disc on a spring attached to the armature. When the push button P is pressed down, its two brass springs touch each other, the current from the battery cell B then flows through the wire W , through the push P, through the coils M M, along A to the platinum disc, out INTRODUCTION at S, which touches this disc, and back to the battery. The instant this is done the current causes the iron cores to become magnets, they attract A, which then breaks contact at S'. The spring mounting of A causes it to jump back to its first position, 5* then touches the platinum disc again, the current flows as before, and the arma- ture is again attracted only to break contact with S' and fly back. This continual making and breaking of the circuit keeps up as long as the push is pressed, a ball mounted on A by means of a rod strikes against the gong G causing a continuous ringing of the bell. The wires leading between the bell, battery cell and push must all be insulated, that is, covered with cotton, rubber, etc., which pre- vents the leakage of current should two wires cross each other. Copper wire is mostly used for circuits indoors, the details of the kind and size of wire will be given later on. The main parts of an electric bell circuit are then — the battery to supply the electric current; the circuit, or wires, to carry this current ; a push, or circuit breaker, to control the current flow; and a bell to utilize the current. INTRODUCTION c- I 22 CHAPTER I The Battery The Battery Cell. The battery cell most used in electric bell work is the Leclanche, or some modification of it. The Leclanche battery cell is shown in Fig. 2, Fig. 2 where / is a glass jar, Z a rod of zinc, and P a jar of porous earthenware containing a carbon rod surrounded by powdered carbon and peroxide of manganese. 2 ELECTRIC BELLS AND ALARMS In setting up this cell about four ounces of sal ammoniac (chloride of ammonia) are put into the jar and enough water added to come about half way up the jar. The porous jar P and the zinc Z are then inserted, and the cell is ready for use in a few minutes after the liquid has soaked through the earthenware into the carbon-manganese mixture. Water is often poured into the porous jar through holes in its top to hasten this wetting. Wires are clamped by nuts or set-$crews to the negative terminal on the zinc or the positive ter- minal on the carbon, it generally not being of consequence which terminal is attached to either wire of the circuit. A battery cell could be constructed without the manganese, using simply a plate of carbon and a rod of zinc, but hydrogen gas would be gen- erated on the carbon plate when the cell was work- ing and would stop the current flowing. This is called polarization, and peroxide of man- ganese is a de-polarizer, because it combines with this hydrogen gas almost as fast as it is generated, and prevents, to a great extent, the polarization. But it does not stop it entirely, as will be seen if the Leclanche cell is kept working above its capacity. Then the hydrogen is generated too fast for the manganese to destroy it, and the cell THE BATTERY 3 ceases to work. In this case a rest will often restore the cell to its former power. Cells which have been almost unable to make a bell give even a single tap have been found good again when allowed to remain at rest over night. In setting up a battery cell no liquid should be splashed on the brass terminals or corrosion will take place. Every metal surface where connec- tion is made to allow electric current to pass must be clean and bright, and all screws, or nuts, hold- ing wires must be screwed up tight so that the wires are firmly clamped. Loose or dirty connections are the cause of probably eight out of every ten troubles affecting bells and batteries. When the fluid in a Leclanche cell becomes milky, more sal ammoniac must be added. Or, better still, throw out the old solution, wash the porous jar thoroughly in clean water, scrape the zinc bright, and half fill the cell with fresh solu- tion. The zinc wearing away rapidly or becoming covered with crystals, and a strong smell of am- monia, show generally that the cell is being worked too hard, or that the current is leaking where it should not. A zinc rod in a cell working the average door 4 ELECTRIC BELLS AND ALARMS bell should last for six months, the porous jar for a year. The Dry Cell. The Leclaiiche cell being a cell with much free liquid is liable to dry up if not watched. The dry cell (Fig. 3) is a modern Fig. 3 form of the Leclanche where the liquid is held by an absorbent material, such as blotting paper, or plaster. A typical dry cell* is shown in the figure. An *For full description of this class pf battery see No. 3 Book on “Dry Batteries.” THE BATTERY 5 outside case of zinc is lined with blotting paper dampened with chloride of zinc and sal ammoniac. A carbon rod is then inserted in the centre and packed around with carbon dust and peroxide of manganese. The latter mixture is also somewhat dampened. Molten wax, or a suitable composition, is then poured on top of the contents of the cell to seal it up and prevent the evaporation of the fluid. A Fig. 4 terminal on the carbon rod and another on the zinc case complete the cell. The voltage of both the Leclanche and the dry cell is about 1.45, when it goes below this it in- dicates that the cell is worked out. The two cells described are known as open- circuit cells and are only intended for intermittent working. When a current is needed for a long period at a time a closed circuit cell should be used, such as the gravity Daniell cell. 6 ELECTRIC BELLS AND ALARMS The Gravity Daniell Cell. The gravity cell, Fig. 4, has a zinc block Z suspended from the side of the jar and a number of copper leaves C standing on edge at the bottom. A quantity of bluestone (sulphate of copper) is poured over the copper leaves and the jar filled with water. During the working of this cell, copper is de- posited on the copper plate, and sulphate of zinc formed at the zinc. To hasten the action a small quantity of zinc sulphate can be added to the solution when setting up the cell. The name of this cell comes from the fact that the copper solution being heavier remains at the bottom of the jar. If the cell is not worked enough, all the solution will become blue and the zinc will blacken. If very dirty from this cause, remove the zinc, scrape and wash ‘it thoroughly. Throw out all the solution, add new sulphate and water and replacing the zinc, then put the cell on short circuit by connecting the copper and zinc together for a few hours. E. M. F. The e. m. f. of a gravity cell is within a fraction of one volt, its current nearly one-half ampere. Warmth makes it give a greater current; on no account let a gravity cell freeze. THE BATTERY 7 Resistance of a Cell. The fluids in a cell do not conduct electricity as well as copper does ; they offer more resistance and thus reduce the current output. The internal resistance of a cell may be low- ered by using large zinc plates curled around the porous pot. The Samson cell has a large zinc plate bent in the form of a cylinder, the carbon-manganese combination standing in the centre of it. The dry cell also has a large zinc, the internal resistance being thus much lowered, the current output is increased. This is by reason of Ohm’s law, which teaches that to increase the current flow, either the voltage of the battery must be in- creased, or the resistance decreased. But increased current means lessened life; there is only just so much energy in a cell mainly de- pendent on the quantity of chemicals. Grouping of Cells. Cells may be grouped in a battery to get increased voltage, or increased am- perage. When connected for the former, they are in series, the carbon of one is connected to the zinc of the next, and so on. If all the carbons are connected together and all the zincs, they are in multiple, and will give the 8 ELECTRIC BELLS AND ALARMS same voltage as -of one cell but the combined am- perage of all. In ordinary bell work the series is the general connection, the higher the resistance of the cir- cuit, or the longer the wires, the more voltage is required. CHAPTER II Bells and Pushes Electric Bells. The two main types of house bells are the iron box and the skeleton. The iron box has a cast-iron frame, or base, and a cast- or stamped-iron cover over the mechanism. The skeleton bell has an iron frame but no cover, and is generally better finished and more expensive than the iron box bells. For fire alarm purposes, mechanical bells or gongs are made, in which a clockwork mechan- ism causes the hammer to strike the gong upon being released by electromagnetism. Marine or waterproof bells have an iron cover fitting tight over a rubber gasket; they are for marine, or mining, work. Polarized, or magneto, bells are used in tele- phone work, and are rarely operated by a battery, but have a miniature dynamo generator operated by hand, or power, to supply the actuating cur- rent. Most bells are classed for size by the diameter of the gong, a four-inch bell being one with a gong four inches in diameter; a six-inch bell one with a six-inch gong, and so on. 10 ELECTRIC BELLS AND ALARMS According to the use for which they are in- tended, bells may be vibrating, as before described, single-stroke, shunt or short-circuiting, differen- tial, continuous-ringing, or adapted for circuits of high voltage. The Single-stroke Bell. The bell before de- scribed, and again shown in Fig. 5, is a vibrating, or trembling, bell. It is often desired to have the hammer give only one stroke for each pressure of the push, as in signaling with a code of taps; in this case a single-stroke bell is used. The circuit from the binding posts is then directly through the magnet coils without any break at the contact screw, as in Fig. 6. In adjusting such a bell to give a clear sound, press the armature up against the iron magnet cores and then bend back the hammer until it just clears the gong. The spring of the hammer wire will carry the hammer sufficiently forward to hit the gong. The tone will be clearer than if the hammer dampered the gong by pressing against it when the armature was nearest the core. BELLS AND PUSHES 11 By bringing out a third connection, a vibrating bell may be made both single stroke and vibrating. The Shunt Bell. There is a form of bell, Fig. 7, known as the shunt, or short circuit bell, which is often used when two or more are to be connected in series, as will be seen in the descrip- tion of circuits. In this bell the circuit through the magnets is not broken at the contact screw, but the forward movement of the armature short circuits the coils. As the short, or shunt, circuit is very much lower in resistance than the wire on the magnet coils, the main current flows around the latter and they do not become energized. The sparking at the shunting contact screw is much less than it would be at the ordinary breaking contact screw, and the platinum points last longer. The Differential Bell. Sparking at the break- ing contacts of an electric bell is detrimental to the platinum points, and many remedies have been devised to overcome it. Sparking is due to the self-induction of one turn of the wire coil acting on its neighbor, and this property is utilized in the gas engine, or gas- lighting spark coil, where a fat spark is needed to ignite gas. 12 ELECTRIC BELLS AND ALARMS The differential bell has two windings in oppo- site directions. The action of one would be to produce an N-pole at one end and an S-pole at the other. But the second coil produces poles just the opposite, as the polarity of a magnet depends on the direction in which the current flows around it. Where the current flows around the first wind- ing the armature is attracted and its spring con- tact meets the contact screw and allows the cur- rent to divide, part flowing through the first coil, the other flowing in the reverse direction in the opposite way. One coil would tend to produce an N-pole where the other coil produced an S-pole, and these opposite poles would so neutralize each other that there would be no magnetism. The armature would therefore be pulled back by its spring when both coils were thrown into circuit. In so doing it would cut out one coil and the same series of operations would recom- mence. As a spark is normally produced where mag- netism is lost by a break of circuit,* no spark ap- pears, as magnetism is produced by a break of circuit in this case. *For a full explanation of self-induction see No. I of this series. BELLS AND PUSHES 13 Continuous-ring Bell. In some classes of bell work, such as burglar alarms, it is desired that the bell when once started shall continue to ring until stopped by the person called. In this case a con- tinuous-ringing bell is needed, such as in Fig. 8. When the push P is pressed, the current flows Fig. s in the usual way through contact screw L, arma- ture spring A, magnet coils M M, battery B, back to P, and the bell rings. But on the first forward movement of the armature it releases the spring contact S, which flies forward and makes contact at U. The circuit is now from B, through M M , 14 ELECTRIC BELLS AND ALARMS to A, thence through L and S, to U and back to B. The bell will continue to ring until the spring contact .S' is moved back and caught by the pro- jection on the armature A. A continuous-ring attachment is also made and sold in most electrical supply stores, which is com- plete in itself and can be applied to any bell. Fig. 9 Waterproof Bells. In Fig. 9 is an example of a waterproof bell where the mechanism is almost all entirely encased in a waterproof brass case. The circuit is made and broken inside the case, but the magnet cores project through it and act on a second armature placed outside. This sec- ond armature carries the hammer which strikes the gong and is governed in speed by the contact- breaking armature inside. BELLS AND PUSHES 15 Forms of Bell Gongs. In order to provide a variety of sounds, bells are provided with gongs of various shapes. Fig. 10 shows the ordinary form of gong. Fig. 10 Fig. 11 Fig. 12 Fig. 13 Fig. 11, a tea gong; Fig. 12, a cow gong; and Fig. 13, a sleigh bell. A coil of steel wire is also used, as in Fig. 14, which on being struck by the hammer gives a pleasant but not loud tone. Fig. 14 The Buzzer. The buzzer is the mechanism of a vibrating bell less the hammer and gong. As the armature vibrates it makes a buzzing noise which does not carry as far as the sound from a struck gong. It is used chiefly for a desk call 16 ELECTRIC BELLS AND ALARMS and in telephone exchange work, or any place where general attention is not desired to the signal. Operating Bells at a Distance. When it is desired to ring a bell situated at a considerable distance from the push, the resistance of the line becomes objectionable. Fig. 15 On lines of 500 feet, No. 18 copper wire and upwards, the battery necessary would be very large, two small batteries and a relay would prove more satisfactory. In Fig. 15 the circuit of a simple form of relay is given. An adjustable contact screw C is placed where an extension S' of the armature A can strike BELLS AND PUSHES 17 it. This extension is provided with a platinum contact. The connections are as in the figure. When the push P is depressed, the current from the main battery M energizes the electromagnet E , and the armature A being attracted, contacts 5 and C meet. These contacts close the second cir- cuit containing the bell 3 and the local battery L. The relay resembles a second push near the bell, but controlled by current from a distance instead of being depressed by hand. Its advan- tage consists in it needing but a very weak cur- rent to move the armature A, which is held back by a light spring, or by gravity. The relay may then be set near the bell and the wires from the push may be of a very great length. Battery L, which actually rings the bell, will thus only have to work through a few feet of wire. Reducing Resistance of a Bell. Sometimes it is desired to reduce the resistance the bell coils offer to the current, the bell then working over a very short line with few cells of battery. Or the bell coils may have been wound with fine wire for large battery voltage and a long line. The bell coils may be put in multiple, the cur- rent then dividing and one-half going through each spool. 18 ELECTRIC BELLS AND ALARMS Untwist the joint between the spools near the yoke or iron bar to which the spools are attached. Join one of these ends to the wire at the armature end of the other spool and the second untwisted end to the armature end wire of its neighboring spool. Use short pieces of insulated wire for these extra connections. The current now instead of having to go through one spool and then the other, can branch through both at once. The resistance to the current of one spool is half the resistance of two, the current through one spool will therefore be twice that through the two spools as at first connected. And as there are two paths for it, each one-half the first resistance, the total will be only one-fourth the resistance of the ordinary series arrangement. The same size battery will therefore send four times the current through the spools in multiple than when they are in series. It is to be noted that the wire on one spool is wound in the reverse direction to that on the other. The reason will be apparent if the two spools and yoke are considered as merely one spool bent in a U or horseshoe form. If both spools were wound in the same direc- tion they would be in opposite directions when the U were straightened out, and would cause like BELLS AND PUSHES 19 poles at the same ends. These poles would neu- tralize one another, so that there would be no magnetic attraction. This can be readily proved by joining together the two yoke ends and the two armature ends of the spool wires. Then pass the current through these two joined connections. Fig, 18 Fig. 19 Fig. 17 Fig. 16 The Push Button. Push buttons, or pushes, are made in a variety of forms, with metal, wood, hard rubber, or porcelain bases. Fig. 16 has a metal base, and is suitable for a front door. Fig. 17 is a wooden pear push, and is attached at the end of a cord which has the two conductors braided in it, each, however, having its own in- sulation. Fig. 18 is a plate push for an outside door. 20 ELECTRIC BELLS AND ALARMS Fig. 19 is either of metal, wood, or porcelain, and is the shape most commonly used. A three-point push has three contact springs. One is movable by means of the button, one is below the movable spring, and the third is above it. When the push button is not being depressed, the movable spring makes contact with the upper spring. But when the button is depressed, these two springs part, and the movable spring makes contact with the lower one. This style of push is used for special bell and annunciator work, as will be described later. The form of combination floor and table push in Fig. 20 is the most solidly constructed device of its kind. The lower part is set in a hole bored in the flooring, the metal flange keeping it in place and preventing its slipping through. . BELLS AND PUSHES 21 The floor push attachment works as follows : The central metal rod is divided into two parts B D y by an insulating piece of hard rubber. When depressed against the action of the spiral spring by the foot, the upper part B connects together the contact springs A C , closing the circuit of bell and battery. These contact springs are insulated from each other by a hard rubber block R. From the table push a cord containing two in- sulated wires leads to the two parts of the rod at B and D. When the push centre is pressed down, the push springs come together and practi- cally short circuit B and D , which completes the circuit of bell and battery. At any time the centre rod may be removed, leaving a surface almost flush with the carpet, or floor, over which furni- ture may be moved without injury to the mechan- ism of the push. For a floor push alone a shorter form of the centre rod is also sometimes furnished which is not divided by insulation. The spiral spring keeps it clear of the lower contact A but enables it to always make connection with the upper con- tact B. Pressing this rod down will also short circuit the bell and battery so that the signal is given. A door pull attachment, like Fig. 21, is made so that the ordinary form of lever pull bell may 22 ELECTRIC BELLS AND ALARMS be changed into an electric bell. Being screwed up near the door pull, a wire is run front the lat- ter and fastened to lever L. When the pull is drawn out the lever L turns on a pivot and a projection presses the insulated spring S against the metal base B. The circuit of the bell and battery being thus closed, the bell rings. Indicating Push Button. A push button is made which contains in the base a small electro- magnet in series with the line. An armature on a spring is fixed near the magnet poles. When the push is depressed, the current travels through this electromagnet, and as the circuit is made and broken at the distant bell, it is also interrupted in the electromagnet. The armature vibrates in unison with the bell and thus gives an audible indication that the bell is ringing. CHAPTER III Wiring , Circuits and Troubles The Wire. The size of the copper wire used in bell work is No. 16, or No. 18, B and S gauge, and sometimes smaller, such as No. 20 to 22. But smaller wire than No. 18 has too much re- sistance, and would necessitate a larger battery power, even if its mechanical strength were not too low. The insulating coverings are cotton satu- rated with paraffin wax or compounds. The covered wires are variously known as an- nunciator, office, or weatherproof wire, these terms being mostly for distinction of the coverings and not for the use to which the wire would be put. Annunciator wire has two layers of cotton merely wrapped around the copper and then satu- rated with paraffin. Office wire has the two cotton layers braided, the inside one being filled with a moisture-repel- ling compound. Both office and annunciator wires have their outside coverings filled with paraffin and highly polished. From the ease with which annunciator wire is 24 ELECTRIC BELLS AND ALARMS stripped of its cotton covering, the braided office wire is to be preferred. These coverings are made in a variety of colors. Weatherproof covered wire is mostly used for electric light work, but the sizes given above are good for bell work, although their larger outside diameter makes them harder to conceal. The approximate number of feet to the pound of office and annunciator wire is given in the table. Office Wire. Annunciator Wire. No. Feet per lb. No. Feet per lb. 12 35 18 180 14 55 20 225 16 95 18 135 Joints. Upon the care with which a joint is made much depends, a loose or poorly made joint will offer much resistance to the current. The correct way to start a joint in annunciator, or office, wire is shown in Fig. 22. About three inches of each wire to be joined is bared of its insulation and scraped bright. The ends are then WIRING, CIRCUITS AND TROUBLES 25 bent at right angles to each other, hooked together and one end firmly twisted around the other, as shown in Fig. 23. Any projecting pieces are cut off, and the joints should then be soldered to pre- vent corrosion. Fig. 22 (ZZZZZZZZ zzzzzzzzza Fig. 23 a t t / # f .i jy Ictzxjez la Fig. 24 Adhesive tape (“friction tape”) is wrapped around the joint, Fig. 24, and pressed firmly to- gether so that there is no chance of its unravelling. The tape wrapping should extend across the joint and on to about a half inch of the insulation around each wire. 26 ELECTRIC BELLS AND ALARMS Running the Wires. To detail all the opera- tions of installing a complex system of bell, alarm and annunciator wires would be impossible from the reasons that conditions vary and space is lim- ited. General directions will then only be given to enable the inexperienced to run such wires as may be needed in ordinary domestic work and to guard against the most common causes of failure. Wires may be run in tin tubes to prevent the depredations of rats and mice, or they may be run with simply their own covering for protection ; it is presumed the latter is undertaken. In a case where the building is of frame and in course of erection the task is much simplified. Having first decided upon the plan, number of bells, pushes, etc. and their location, proceed to run the wires first in order that the pushes, bells, etc. may not be injured. But where the house is already occupied, as in the majority of cases likely to be met with by the reader, the bell and battery may be set first. Take the case of an ordinary door bell with the push at the front door, the bell in the kitchen and the battery in the cellar. If possible get the wire on two spools; it will simplify matters if both wires are of different colors. Starting at the push, have a foot of each wire for connection and slack, and fasten each wire lightly to the woodwork with WIRING, CIRCUITS AND TROUBLES 27 staples, or double-pointed tacks, never putting two wires under one staple nor driving in a staple so it cuts the insulation. Some cases will require a staple about every foot, on straight runs some- times every three feet. In many cases the wires can be partly con- cealed in the angle between a moulding and the wall, or even in a groove of the moulding itself. When running along a skirting, the wires may often be pushed out of sight between it and the floor. Do not attempt to draw the wires too tight or the changes of the weather may break the wires when the woodwork shrinks or swells. The wires will be, one from the push to the bell, one from the push to the battery, and one from the bell to the battery. So it is probable that the second wire can be run right through a small hole bored in the flooring under the push, but inside the front door. In this case it will be perhaps easier if the spool be left in the cellar and the end of the wire be pushed up from below and stapled to the woodwork near the push, leav- ing the cellar work to the last. Only one wire will be run then direct to the bell upstairs and it can be better concealed than two. If necessary it may be drawn under a carpet and not stapled, or it can often be forced into the crack between two boards, But if not, run it 28 ELECTRIC BELLS AND ALARMS along the skirting, following the walls until it reaches below the bell. It is often better to go entirely around a room than to cross below a door. If a door must be crossed the wire may either run up one side of the frame and down the other or laid beneath the carpet on the sill. The former is preferable, but takes more wire. In many houses the bell wire as well as the bat- tery wire may be run across the cellar beams (Fig. 25), in which case bore a second hole for it near the push ; do not draw it through the same hole as the push to battery wire. And, of course, here work upwards with the spool in the cellar. Having reached the bell location, run the third wire down into the cellar to the battery. Now connect up the push, baring an inch or so of each wire, push them through the holes provided in the push base, screw down the push base and clamp the wires under the washers through which the connection screws run. Do this neatly, be sure the ends of the wires do not stick out, cut off what is left free of the bared ends. Then con- nect the battery to the wire from the push and the wire from the bell. The last thing is to scrape and fasten the bell wires to the bell binding posts. Do this so that they cannot come loose and that they make good contact. Fig. 25 30 ELECTRIC BELLS AND ALARMS The bell should now ring properly when the push is pressed. To sum up, one wire leads from one spring of the push to the bell, one wire from the other spring of the push to the battery, and another wire from the remaining binding post on the bell to the remaining binding post on the battery. It is im- material whether the zinc terminal or the carbon terminal go to the bell or push. Combinations of Bells and Pushes. One of the wires in a bell circuit may be replaced by the ground (Fig. 26). Connection may be made to a gas or water pipe or to a metal plate buried deep in damp earth. Any wire fastened to such a plate must be thoroughly soldered to it or a voltaic action will be set up, which will eat it away at the point of contact. When one bell is to be rung from two or more points the pushes are to be connected in WIRING, CIRCUITS AND TROUBLES 31 multiple (Fig. 27) as if they were in series; all would have to be closed to complete the circuit. If two bells are to be operated from one push they may be in series (Fig. 28), but in this case one of them must be arranged for single stroke. If both were vibrating bells the armature of one would not vibrate in unison with the other arma- ture and the result would be irregular contact breaking and intermittent ringing. A preferable connection for two or more bells 32 ELECTRIC BELLS AND ALARMS and one push is Fig. 29, where the bells are in multiple. This requires more current than the series method. To ring two bells from either one of two points, the arrangement in Fig 30 will answer. It re- quires only two wires or one wire and ground return, but two batteries. As both bells are in Fig. 31 multiple both will ring, the one nearest the push being depressed ringing the loudest. This is a dis- advantage. If the series arrangement in Fig. 31 WIRING, CIRCUITS AND TROUBLES 33 be selected, one bell must be arranged for single stroke. Both bells will ring with equal power. In Fig. 32 only the distant bell rings, the cir- cuit having only one battery but three wires, or two wires and ground return. A plan where two batteries are needed but only two wires, or one wire and ground is in Fig. 33. Fig. 33 here, making one contact when depressed and a second one when not being touched. In this figure only the distant bell rings. 34 ELECTRIC BELLS AND ALARMS Faults in Bells. On examining many electric bells it will be noted that only one binding post is insulated from the frame when the latter is Fig. 34 of iron (Fig. 34). As the armature spring S' is in electrical connection with the frame F by reason of its metal screws and support, the circuit may run from the insulated post U to the magnet eoils, thence through the insulated contact screw C through the armature spring (when it is making contact) and through the frame to the uninsulated post /. This saves labor, wire and complication, but if the insulation of the post U, the wires W V , or the contact screw C be injured, the current may take a short path back to the frame. If C were thus grounded, the bell would act as a single-stroke bell. If C/ were grounded, the bell would not ring WIRING, CIRCUITS AND TROUBLES 35 at all, as that would be a short circuit on the bat- tery between / and U and the latter would also result if the bare wire were touching the frame at V. If the bare wire touched the frame bevond M M, that is, along W, it would be a single-stroke bell, as if C were grounded. As any one of these faults is likely to occur, they should be looked for when the bell acts im- perfectly, or not at all. A very common fault in a bell is when its arma- ture sticks to the cores and thus does not make contact with the contact screw. This may be from a weak spring or because of the loss of the pieces of brass inserted in the ends of the cores to keep the armature away from actual contact. A piece of a postage stamp stuck over the core end will often help out in the latter case. A high screeching noise from the armature vi- brating too rapidly but with too little play, may be from excessive battery power or the contact screw being too far forward. The former will generally be detected by the violent sparking as well as the rapid vibration. In very cheap bells the platinum contacts may be replaced by German silver or some other metal. Platinum is necessary because the sparking would soon corrode other metals, but it is very 36 ELECTRIC BELLS AND ALARMS expensive. To test for platinum put a tiny drop of nitric acid on the suspected metal. If bubbles or smoke appear it is not platinum. After apply- ing this test in any case however, carefully wash off and remove all traces of the acid, as it will cor- rode the metal into which the platinum is riveted. Dirty contacts will decrease the current in the bell coils and it will not work well, if at all. Loose contact screws and wires also give trouble. The adjusting of the contact screw is of the utmost importance, and should never be at- tempted 'unless it is clearly necessary. Faults in Line. In looking for a fault in a bell circuit make sure the battery is working; if only one or two cells, put the ends of two wires attached to the terminals on the tongue : a metallic taste will indicate current. Then see that the circuit wires are firmly clamped in the terminals and no dirt or corrosion on the connections. Next examine the push button and see that the wire connections at the springs are perfect. If there is no movement of the bell at all when the push is pressed in, take a pocket knife or screw driver, and touch the blade across the push springs. If there is current flowing sparks will be seen when the blade breaks contact between WIRING, CIRCUITS AND TROUBLES 37 the springs. If there are no sparks, detach the wires from the bell and twist the bare ends to- gether. Then try again for sparks — they may now be very minute. The tongue test is good here. If current is detected, examine the bell for the defects first mentioned. But if no current is found at the push now the wires are broken somewhere. First short circuit the push springs by insert- ing a knife blade or piece of wire so as to touch both of them. Then touch the two wires at the bell, one to each side wire coming from the mag- net coils. If current is up to the bell and the coils are all right, a single stroke should result. Replace the wires in the binding posts, clean the platinum on both contact screw and armature spring and try the adjustment. Troubles in the bell will be mostly similar to those before men- tioned. If no current has been obtained at either bell or push, and the battery is in good working order, the line must be tested for a cross or break. If the wires are touching each other (Fig. 35) at some bare spot S' between the bell and the bat- tery, it will be shown by the metallic taste upon detaching one wire from the battery and laying it on the tongue T, together with another wire W from the disconnected terminal of the battery. The 38 ELECTRIC BELLS AND ALARMS current will travel from the battery to the cross at S, then back along the second circuit wire to the tongue and through the short wire to the battery. able that the wire is broken. The easiest way to find this is to take a bell to the battery and connect it between the circuit wires and the battery (Fig. 36). Then with a sharp knife carefully cut away a WIRING, CIRCUITS AND TROUBLES 89 little piece of the insulation from each wire beyond the bell and battery and short circuit the bared spots with the knife blade K. Keep working towards the push. The bell will ring each time at K K until the break D is passed, at C it will not. It becomes an easy matter then to locate it If the bell and push are far apart, as in Fig. 37, a break between the push and the bell may be found as shown. With the knife blade K at differ- ent points the bell will ring, but after passing the break D it will not ring. Such simple tests as are here given can be car- ried out by any one, but far better results will be obtained if the reason for each is first learned. This can be readily done by a careful study of the diagrams and text. CHAPTER IV Alarms Fire Alarms. Thermostats, heat alarms and fire alarms are all practically the same, the term thermostat being applied principally to the appa- ratus which closes the electrical circuit. i i i I i i Fig. 38 Thermostats act on the principle that heat causes expansion whether of substances, liquids, or gases. The degree in which different substances ex- pand varies for the same increase in temperature. This fact is used in a common form of thermo- stat shown in Fig. 38. A strip of wood or hard rubber R has a strip of thin sheet metal S riveted to it. This compound strip is held at one end by ALARMS 41 a lug L screwed fast to a baseboard. Upon an increase of temperature the hard rubber expands more than the metal strip and the compound strip bends towards the adjustable contact screw A. Upon touching the latter, the circuit through the bell B, battery C and the metal strip 5" is com- pleted, and the bell rings. A contact screw can be arranged at the other side of S R, which will give warning of a decrease in temperature, as the rubber contracts more than the metal strip. In some thermostats of this character two metals having different coefficients of expansion, such as steel and brass, are used instead of metal and hard rubber. Thermostats of this nature are much used in incubators, and they can readily be combined with electric apparatus to open or close hot-air valves, 42 ELECTRIC BELLS AND ALARMS dampers, etc., and thus regulate the supply of hot air, hot water, or gas. A thermostat much used in fire alarm work has a thin metal chamber which is air tight. An in- crease of temperature causes' the air to expand, which swells out the walls of the chamber and closes an electric circuit. A 0 ^ B <0 Q- J0 cp i i (k c ■(S) •fl 1, 1 L_ f L ~'0 — o c FIG. 69 The annunciator bell is at /, an auxiliary bell being added in multiple with it when necessary. ’ 3 f 9 9 0 ( 3 .( 3 < FIG. 70 fiHMW FIRE ALARM SYSTEMS 83 Fire Alarm System for Considerable Areas. Where the area is more extensive and the number of stations considerable, the system illustrated in Fig. 70 is very suitable. It consists of the requisite number of break-glass boxes, bells and a more elaborate annunciator system. In general details it resembles the last system, but uses a relay to send out the current for ringing the alarm bells. When a box operates, the current impulses sent on the line act on the relay instead of directly on the bells. Each stroke of the relay closes a local circuit which includes the bells and the battery. This system does away .with large batteries and is very enconomical of wire. The current needed for the relay is very small, whereas in a direct sys- tem of any size, the current and voltage to ring a number of bells located at wide intervals would be prohibitive. The reference letters are as follows: AA are the alarm bells, BB the break-glass alarm boxes, C is the annunciator bell, D is the relay which re- mains closed when an alarm comes in keeping the bells constantly ringing until shut off. £ is a re- sistance coil and F is the battery. A system cut-out switch G and JJ switches on the annunciator for controlling individual circuits are also provided. HH are the annunciator drops and K is a constant-ring switch which can also be used for a general alarm to ring all the bells at once. SELENIUM CELLS THE Construction, Care and Use of Selenium Cells with Special Reference to the Fritts Cell By ' Thomas W. Benson The lack of definite information relative to the construction of Selenium Cells has led the writer to record the results of some of his experiments and to fully describe the apparatus as developed by him. Contents of Chapters 1. Selenium The Element 2. Consideration of Cell types and their Characteristics; The Bildwell Cell; The Ruhmer Cell; The Mercadier Cell; The Bell and Taintor Cell; The Gripenberg Cell 3. Construction of Fritts Selenium Cells 4. Testing and Maturing Selenium Cells 5. Applications of Selenium Cells 6. The Care of Selenium Cells 73 pages, 15 diagrams and 3 halftone page plates, 734 x 534 inches. Cloth, $1.50 Everybody Wants This Book. 0) j j iii £ I 0 o u z oc H E— pj >- cn < pa >- a < UJ 0£ -J < a < I CO < I >“ CQ Z £ 0 X co co < X f— ■ ft! 1 b CO W -J ~ < Q W “ UJ > u O cd a: < o- j ^ H X H tn h z UJ h z 0 o "TD d fa J 0 d ~ 3^ a » H 0 >, © m y 5- 41 s a 0 = • N S 6 see C 9 B <$• 1 i z • a 'S s *g « 0 s w * 13 NEW DESIGNS